WIP: functional checkpoint!

src/board/heltec_v3.rs

@@ -37,8 +37,7 @@ impl Board {
         core::mem::forget(vext); // hold pin low permanently; drop would reset it
 
         let radio = esp32s3::init_radio(
-            p.SPI2, p.DMA_CH0, p.GPIO9, p.GPIO10, p.GPIO11, p.GPIO8, p.GPIO12, p.GPIO14,
-            p.GPIO13,
+            p.SPI2, p.DMA_CH0, p.GPIO9, p.GPIO10, p.GPIO11, p.GPIO8, p.GPIO12, p.GPIO14, p.GPIO13,
         );
         let usb = esp32s3::init_usb(p.USB0, p.GPIO20, p.GPIO19);
         let i2c = esp32s3::init_display_i2c(p.I2C0, p.GPIO17, p.GPIO18);

src/board/heltec_v4.rs

@@ -37,8 +37,7 @@ impl Board {
         core::mem::forget(vext); // hold pin low permanently; drop would reset it
 
         let radio = esp32s3::init_radio(
-            p.SPI2, p.DMA_CH0, p.GPIO9, p.GPIO10, p.GPIO11, p.GPIO8, p.GPIO12, p.GPIO14,
-            p.GPIO13,
+            p.SPI2, p.DMA_CH0, p.GPIO9, p.GPIO10, p.GPIO11, p.GPIO8, p.GPIO12, p.GPIO14, p.GPIO13,
         );
 
         // Note: switches internal USB PHY from Serial-JTAG to OTG.

src/board/rak_wisblock_4631.rs

@@ -87,7 +87,6 @@ impl super::traits::LoRaBoard for Board {
 }
 
 impl Board {
-
     pub fn into_parts(self) -> (RadioParts, UsbParts, Option<DisplayParts>) {
         let p = self.p;
 
@@ -108,7 +107,8 @@ impl Board {
         let dio1 = Input::new(p.P1_15, Pull::Down);
         let busy = Input::new(p.P1_14, Pull::Down);
 
-        let iv = GenericSx126xInterfaceVariant::new(reset, dio1, busy, None, None).expect("SX1262 interface init");
+        let iv = GenericSx126xInterfaceVariant::new(reset, dio1, busy, None, None)
+            .expect("SX1262 interface init");
 
         let sx_config = sx126x::Config {
             chip: Sx1262,
@@ -125,7 +125,9 @@ impl Board {
         // ── USB ──────────────────────────────────────────────────
         static VBUS: StaticCell<embassy_nrf::usb::vbus_detect::SoftwareVbusDetect> =
             StaticCell::new();
-        let vbus = VBUS.init(embassy_nrf::usb::vbus_detect::SoftwareVbusDetect::new(true, false));
+        let vbus = VBUS.init(embassy_nrf::usb::vbus_detect::SoftwareVbusDetect::new(
+            true, false,
+        ));
         let usb = UsbParts {
             driver: Driver::new(p.USBD, Irqs, vbus),
         };

src/board/wio_tracker_l1.rs

@@ -0,0 +1,154 @@
+use embassy_embedded_hal::shared_bus::asynch::spi::SpiDevice;
+use embassy_nrf::gpio::{Input, Level, Output, OutputDrive, Pull};
+use embassy_nrf::spim::{self, Spim};
+use embassy_nrf::twim::{self, Twim};
+use embassy_nrf::usb::Driver;
+use embassy_nrf::{bind_interrupts, Peripherals};
+use embassy_sync::blocking_mutex::raw::NoopRawMutex;
+use embassy_time::Delay;
+use static_cell::StaticCell;
+
+use lora_phy::iv::GenericSx126xInterfaceVariant;
+use lora_phy::sx126x::{self, Sx1262, Sx126x};
+
+use super::traits::LoRaBoard;
+
+bind_interrupts!(struct Irqs {
+    USBD => embassy_nrf::usb::InterruptHandler<embassy_nrf::peripherals::USBD>;
+    SPIM3 => embassy_nrf::spim::InterruptHandler<embassy_nrf::peripherals::SPI3>;
+    TWISPI0 => embassy_nrf::twim::InterruptHandler<embassy_nrf::peripherals::TWISPI0>;
+});
+
+// ── Concrete peripheral types ────────────────────────────────────────
+
+type SpiBus = Spim<'static>;
+type Nss = Output<'static>;
+type Iv = GenericSx126xInterfaceVariant<Output<'static>, Input<'static>>;
+type RadioSpiDevice = SpiDevice<'static, NoopRawMutex, SpiBus, Nss>;
+/// SX126x driver (pre-LoRa construction — LoRa::new is async).
+pub type RadioDriver = Sx126x<RadioSpiDevice, Iv, Sx1262>;
+
+/// USB driver for CDC-ACM.
+pub type UsbDriver = Driver<'static, &'static embassy_nrf::usb::vbus_detect::SoftwareVbusDetect>;
+
+/// I2C bus for SH1106 OLED.
+pub type DisplayI2c = Twim<'static>;
+
+// ── Peripheral bundles ───────────────────────────────────────────────
+
+pub struct RadioParts {
+    pub driver: RadioDriver,
+    pub delay: Delay,
+}
+
+pub struct UsbParts {
+    pub driver: UsbDriver,
+}
+
+pub struct DisplayParts {
+    pub i2c: DisplayI2c,
+    pub mac: [u8; 6],
+}
+
+// ── Board init ───────────────────────────────────────────────────────
+
+pub struct Board {
+    p: Peripherals,
+}
+
+impl super::traits::LoRaBoard for Board {
+    const NAME: &'static str = "Wio Tracker L1";
+    const TX_POWER_RANGE: (i8, i8) = (-9, 22);
+
+    fn init() -> Self {
+        let mut config = embassy_nrf::config::Config::default();
+        config.hfclk_source = embassy_nrf::config::HfclkSource::ExternalXtal;
+        config.lfclk_source = embassy_nrf::config::LfclkSource::ExternalXtal;
+        let p = embassy_nrf::init(config);
+        Self { p }
+    }
+
+    fn mac_address() -> [u8; 6] {
+        // SAFETY: 0x10000000 is the nRF52840 FICR (Factory Information Configuration
+        // Registers) base address. Offsets 0x0A4 and 0x0A8 are the DEVICEADDR[0] and
+        // DEVICEADDR[1] registers containing the factory-programmed device address.
+        // read_volatile is correct for memory-mapped hardware registers.
+        unsafe {
+            let ficr = 0x10000000 as *const u32;
+            let addr0 = core::ptr::read_volatile(ficr.byte_add(0x0A4));
+            let addr1 = core::ptr::read_volatile(ficr.byte_add(0x0A8));
+            [
+                addr0 as u8,
+                (addr0 >> 8) as u8,
+                (addr0 >> 16) as u8,
+                (addr0 >> 24) as u8,
+                addr1 as u8,
+                (addr1 >> 8) as u8,
+            ]
+        }
+    }
+}
+
+impl Board {
+    pub fn into_parts(self) -> (RadioParts, UsbParts, Option<DisplayParts>) {
+        let p = self.p;
+
+        // ── SPI bus for SX1262 ───────────────────────────────────
+        let mut spi_cfg = spim::Config::default();
+        spi_cfg.frequency = spim::Frequency::M1;
+        let spi = Spim::new(p.SPI3, Irqs, p.P0_30, p.P0_03, p.P0_28, spi_cfg);
+
+        static SPI_BUS: StaticCell<embassy_sync::mutex::Mutex<NoopRawMutex, SpiBus>> =
+            StaticCell::new();
+        let spi_bus = SPI_BUS.init(embassy_sync::mutex::Mutex::new(spi));
+
+        let nss = Output::new(p.P1_14, Level::High, OutputDrive::Standard);
+        let spi_device = SpiDevice::new(spi_bus, nss);
+
+        // ── SX1262 control pins ──────────────────────────────────
+        let reset = Output::new(p.P1_07, Level::High, OutputDrive::Standard);
+        let dio1 = Input::new(p.P0_07, Pull::Down);
+        let busy = Input::new(p.P1_10, Pull::Down);
+
+        // RF switch: RXEN on P1.08 (GPIO, toggled by lora_phy), TX via DIO2 (SX1262 internal).
+        let rx_enable = Output::new(p.P1_08, Level::Low, OutputDrive::Standard);
+        let iv = GenericSx126xInterfaceVariant::new(reset, dio1, busy, Some(rx_enable), None)
+            .expect("SX1262 interface init");
+
+        let sx_config = sx126x::Config {
+            chip: Sx1262,
+            tcxo_ctrl: Some(sx126x::TcxoCtrlVoltage::Ctrl1V8),
+            use_dcdc: true,
+            rx_boost: false,
+        };
+
+        let radio = RadioParts {
+            driver: Sx126x::new(spi_device, iv, sx_config),
+            delay: Delay,
+        };
+
+        // ── USB ──────────────────────────────────────────────────
+        static VBUS: StaticCell<embassy_nrf::usb::vbus_detect::SoftwareVbusDetect> =
+            StaticCell::new();
+        let vbus = VBUS.init(embassy_nrf::usb::vbus_detect::SoftwareVbusDetect::new(
+            true, true,
+        ));
+        let usb = UsbParts {
+            driver: Driver::new(p.USBD, Irqs, vbus),
+        };
+
+        // ── BAT_CTL: P0.04, active HIGH — enables power to OLED and battery sense
+        let bat_ctl = Output::new(p.P0_04, Level::High, OutputDrive::Standard);
+        core::mem::forget(bat_ctl);
+
+        // ── Display (SH1106 OLED on I2C) ─────────────────────────
+        static TWIM_BUF: StaticCell<[u8; 256]> = StaticCell::new();
+        let twim_buf = TWIM_BUF.init([0u8; 256]);
+        let i2c_cfg = twim::Config::default();
+        let i2c = Twim::new(p.TWISPI0, Irqs, p.P0_06, p.P0_05, i2c_cfg, twim_buf);
+        let mac = Self::mac_address();
+        let display = Some(DisplayParts { i2c, mac });
+
+        (radio, usb, display)
+    }
+}