feat(boards): LilyGo T-Beam (classic) support

First classic-ESP32 (non-S3) board in the firmware, and first SX127x
radio. ESP32 + SX1276 + SSD1306 OLED + AXP192 PMIC, CP2102 USB-UART
bridge. Pin map verified from MeshCore variants/lilygo_tbeam_SX1276.

The AXP192 gates power to the LoRa chip and OLED. Its I²C bus is
shared with the display, so the firmware builds I²C0 in blocking mode
first for the PMIC init, then converts the same handle to async and
hands it to the display task — avoids double-consuming the peripheral.

Lora-phy's Sx127x support drives DIO0 as the sole IRQ (SX127x has no
BUSY line); the chip runs from a crystal, tx_boost routes +20 dBm
through PA_BOOST.

The `esp-hal` / `esp-rtos` / `esp-backtrace` / `esp-println` deps have
been restructured so the chip flavour (esp32 vs esp32s3) is selected
at the per-board feature level instead of baked into the dep lines.
This keeps the existing S3 boards building on esp32s3 while the new
T-Beam feature selects classic esp32 via the same dependency set.

LoRaBoard gains supported_sf_bitmap() / supported_bw_bitmap() methods
(with SX126x defaults) so the T-Beam can report SF6–SF12 via GET_INFO
— the SX1276 has no SF5. radio_chip_id() reports 0x0011 per
donglora-protocol RadioChipId::Sx1276. freq_range_hz widens to the
SX1276 datasheet span of 137 MHz–1020 MHz.

New modules:
- src/hal/esp32.rs           — classic-ESP32 MCU primitives
- src/board/esp32.rs         — Sx127x radio + SSD1306 display pipe
- src/board/lilygo_tbeam.rs  — the board file
- src/driver/axp.rs          — AXP192 init added alongside AXP2101

CHANGELOG.md

@@ -20,6 +20,38 @@ and this project adheres to [Semantic Versioning](https://semver.org/).
     from the SH1106 on I²C0 (SDA=17, SCL=18). I²C1 is used blocking
     for a one-shot init and then dropped.
   - TCXO driven at 1.6 V via DIO3 (MeshCore uses the same).
+- LilyGo T-Beam (classic) board support (ESP32 + SX1276 + SSD1306
+  OLED + AXP192 PMIC, CP2102 USB-UART bridge). This is the first
+  board in the firmware on classic ESP32 (non-S3) and the first on
+  the SX127x radio family.
+  - Pin map verified against MeshCore's `variants/lilygo_tbeam_SX1276`.
+  - New `src/hal/esp32.rs` (classic-ESP32 MCU primitives, peripheral
+    DMA via `DMA_SPI2`) and `src/board/esp32.rs` (SX1276 radio helper
+    + SSD1306 display pipe).
+  - AXP192 init added to `src/driver/axp.rs`: DCDC1 = 3.3 V for the
+    OLED, LDO2 = 3.3 V for the SX1276 PA_BOOST rail. Shares the
+    OLED I²C bus (SDA=21, SCL=22); the I²C instance is built in
+    blocking mode for PMIC init and converted to async for the
+    display task.
+  - SX127x support via lora-phy 3's `Sx127x<Sx1276>` +
+    `GenericSx127xInterfaceVariant` (DIO0 as the sole IRQ; no
+    BUSY line on SX127x). XTAL clocked (no TCXO), `tx_boost = true`
+    for the PA_BOOST path.
+  - `LoRaBoard` trait gains `supported_sf_bitmap()` and
+    `supported_bw_bitmap()` methods with SX126x defaults
+    (`0x1FE0`, `0x03FF`). T-Beam classic overrides SF to `0x1FC0`
+    (SF6–SF12) — the SX1276 has no SF5.
+  - `radio_chip_id()` reports `0x0011` (`RadioChipId::Sx1276`) and
+    `freq_range_hz()` widens to 137 MHz–1020 MHz per the SX1276
+    datasheet.
+
+### Changed
+
+- `Cargo.toml`: the `esp32s3` chip feature has been moved out of
+  the `esp-hal` / `esp-rtos` / `esp-backtrace` / `esp-println`
+  dependency lines and into each ESP board's feature list (as
+  `esp-hal/esp32s3`, etc.). This lets `lilygo_tbeam` select the
+  classic `esp32` chip flavour from the same dependency set.
 
 ## [1.2.1] - 2026-04-23