feat(boards): LilyGo T-Beam (classic) support

First classic-ESP32 (non-S3) board in the firmware, and first SX127x
radio. ESP32 + SX1276 + SSD1306 OLED + AXP192 PMIC, CP2102 USB-UART
bridge. Pin map verified from MeshCore variants/lilygo_tbeam_SX1276.

The AXP192 gates power to the LoRa chip and OLED. Its I²C bus is
shared with the display, so the firmware builds I²C0 in blocking mode
first for the PMIC init, then converts the same handle to async and
hands it to the display task — avoids double-consuming the peripheral.

Lora-phy's Sx127x support drives DIO0 as the sole IRQ (SX127x has no
BUSY line); the chip runs from a crystal, tx_boost routes +20 dBm
through PA_BOOST.

The `esp-hal` / `esp-rtos` / `esp-backtrace` / `esp-println` deps have
been restructured so the chip flavour (esp32 vs esp32s3) is selected
at the per-board feature level instead of baked into the dep lines.
This keeps the existing S3 boards building on esp32s3 while the new
T-Beam feature selects classic esp32 via the same dependency set.

LoRaBoard gains supported_sf_bitmap() / supported_bw_bitmap() methods
(with SX126x defaults) so the T-Beam can report SF6–SF12 via GET_INFO
— the SX1276 has no SF5. radio_chip_id() reports 0x0011 per
donglora-protocol RadioChipId::Sx1276. freq_range_hz widens to the
SX1276 datasheet span of 137 MHz–1020 MHz.

New modules:
- src/hal/esp32.rs           — classic-ESP32 MCU primitives
- src/board/esp32.rs         — Sx127x radio + SSD1306 display pipe
- src/board/lilygo_tbeam.rs  — the board file
- src/driver/axp.rs          — AXP192 init added alongside AXP2101

src/hal/esp32.rs

@@ -0,0 +1,80 @@
+//! ESP32 (classic / non-S3) MCU initialization primitives.
+//!
+//! Mirror of `hal::esp32s3` with a single delta: the classic ESP32 uses a
+//! peripheral-bound DMA (`DMA_SPI2`) rather than the S3's channel-addressed
+//! GDMA (`DMA_CH0`). Timer, I²C, and eFuse access are otherwise identical
+//! between the two Xtensa parts in this esp-hal vintage.
+
+use embassy_sync::blocking_mutex::raw::NoopRawMutex;
+use esp_hal::dma::{DmaRxBuf, DmaTxBuf};
+use esp_hal::gpio::interconnect::{PeripheralInput, PeripheralOutput};
+use esp_hal::i2c::master::I2c;
+use esp_hal::spi::master::{Config as SpiConfig, Spi, SpiDmaBus};
+use esp_hal::spi::Mode as SpiMode;
+use esp_hal::time::Rate;
+use esp_hal::timer::timg::TimerGroup;
+use static_cell::StaticCell;
+
+// ── MCU-level types ─────────────────────────────────────────────────
+
+pub type SpiBus = SpiDmaBus<'static, esp_hal::Async>;
+pub type I2cBus = I2c<'static, esp_hal::Async>;
+
+// ── Timer ───────────────────────────────────────────────────────────
+
+/// Start the ESP-RTOS scheduler and Embassy time driver.
+pub fn start_timer(
+    timg0: esp_hal::peripherals::TIMG0<'static>,
+    sw_int: esp_hal::peripherals::SW_INTERRUPT<'static>,
+) {
+    let timg0 = TimerGroup::new(timg0);
+    let sw_ints = esp_hal::interrupt::software::SoftwareInterruptControl::new(sw_int);
+    esp_rtos::start(timg0.timer0, sw_ints.software_interrupt0);
+}
+
+// ── SPI bus ─────────────────────────────────────────────────────────
+
+/// Initialize SPI2 with peripheral-bound DMA and wrap in a shared bus
+/// (`StaticCell` + `Mutex`).
+///
+/// Generic over pin type. The classic ESP32's matrix of GPIO → peripheral
+/// routes lets any GPIO serve as any SPI signal — same as the S3.
+pub fn init_spi(
+    spi2: esp_hal::peripherals::SPI2<'static>,
+    dma_spi2: esp_hal::peripherals::DMA_SPI2<'static>,
+    sck: impl PeripheralOutput<'static>,
+    mosi: impl PeripheralOutput<'static>,
+    miso: impl PeripheralInput<'static>,
+) -> &'static embassy_sync::mutex::Mutex<NoopRawMutex, SpiBus> {
+    let spi = Spi::new(
+        spi2,
+        SpiConfig::default()
+            .with_frequency(Rate::from_mhz(1))
+            .with_mode(SpiMode::_0),
+    )
+    .expect("SPI init")
+    .with_sck(sck)
+    .with_mosi(mosi)
+    .with_miso(miso)
+    .with_dma(dma_spi2);
+
+    let (rx_buf, rx_desc, tx_buf, tx_desc) = esp_hal::dma_buffers!(256);
+    let dma_rx = DmaRxBuf::new(rx_desc, rx_buf).expect("DMA RX buf");
+    let dma_tx = DmaTxBuf::new(tx_desc, tx_buf).expect("DMA TX buf");
+
+    let spi = spi.with_buffers(dma_rx, dma_tx).into_async();
+
+    static SPI_BUS: StaticCell<embassy_sync::mutex::Mutex<NoopRawMutex, SpiBus>> =
+        StaticCell::new();
+    SPI_BUS.init(embassy_sync::mutex::Mutex::new(spi))
+}
+
+// ── MAC address ─────────────────────────────────────────────────────
+
+/// Read the factory-programmed MAC address from eFuse.
+pub fn mac_address() -> [u8; 6] {
+    esp_hal::efuse::base_mac_address()
+        .as_bytes()
+        .try_into()
+        .expect("MAC is 6 bytes")
+}

src/hal/mod.rs

@@ -12,6 +12,9 @@
 ))]
 pub mod esp32s3;
 
+#[cfg(feature = "lilygo_tbeam")]
+pub mod esp32;
+
 #[cfg(any(feature = "rak_wisblock_4631", feature = "wio_tracker_l1"))]
 pub mod nrf52840;