feat(t114): add Heltec Mesh Node T114 board support

Adds nRF52840 + SX1262 + 1.14" 240×135 ST7789 color TFT support. First
color display board in the project; introduces a BoardDisplay trait so
each board renders to its native pixel format and resolution without
aliasing or color-quantization round-trips.

Architecture:
- New BoardDisplay trait (src/display.rs) bundles render_*, present(),
  set_bright/set_dim. Replaces the old DrawTarget<Color=BinaryColor>
  + DisplayBrightness combo as the LoRaBoard::DisplayDriver bound.
- Mono OLED drivers (Sh1106, Ssd1306Async) get adapter impls that
  delegate to the existing display::render module — no behavior change
  for any existing board.
- T114 ST7789 driver (src/driver/st7789.rs) wraps lcd-async (async fork
  of mipidsi) with a 64,800-byte raw byte framebuffer in .bss. Renders
  via lcd_async::raw_framebuf::RawFrameBuf<Rgb565, _>, presents via a
  single async DMA blit (panel.show_raw_data(...).await) — the await
  yields the executor for the ~65 ms SPI transfer so the radio task
  isn't starved during repaints.
- PWM backlight on PWM0 / P0.15 (active-LOW, inverted polarity) for
  smooth dim/bright transitions instead of GPIO toggle.
- Native 240×135 Rgb565 renderer (src/display/render_color.rs) with
  splash + dashboard + sparkline.
- Shared QR-code blit (src/display/qr.rs), generic over PixelColor,
  re-centers the 64×64 bitmap which has cells in cols 0..50 and ~14 px
  of right-side padding — both mono and color splash now show the QR
  with 7 px quiet zones on all four sides (was visibly left-shifted).
- Shared content types (BoardInfo, DashboardCtx) decouple what to draw
  from how each board renders it.
- create_display() now takes the board's full DisplayParts bundle
  (was just the I2C bus) so non-I2C displays can carry SPI + control
  pins through.

Hardware:
- VEXT_ENABLE on P0.21 driven HIGH at boot — powers the SX1262 + TFT
  rail. Without this, lora-phy init succeeds at the SPI level but
  TX_DONE never fires.
- VTFT_CTRL on P0.03, active LOW; backlight on P0.15, active LOW.
- TFT SPI2 (SCK P1.08 / MOSI P1.09) at 8 MHz over EasyDMA. Async
  ExclusiveDevice from embedded-hal-bus (with the 'async' feature).
- lcd-async builder at display_size(135, 240), display_offset(52, 40),
  Deg90 rotation, ColorInversion::Inverted — standard 1.14" ST7789
  die mapping.
- Linker: shared ld/nrf52840-memory.x (S140 SoftDevice preserved at
  0x01000-0x26000 per project policy).

src/board/traits.rs

@@ -6,10 +6,7 @@
 //!
 //! See `src/board/PORTING.md` for a step-by-step guide to adding a new board.
 
-use embedded_graphics::draw_target::DrawTarget;
-use embedded_graphics::pixelcolor::BinaryColor;
-
-use crate::driver::DisplayBrightness;
+use crate::display::BoardDisplay;
 
 /// Async RGB LED control. Boards without an LED use `()` which is a no-op.
 pub trait RgbLed {
@@ -37,9 +34,10 @@ pub trait LoRaBoard: Sized {
     /// Display peripheral bundle (I2C bus for display init).
     type DisplayParts;
 
-    /// Concrete display driver type (must implement DrawTarget for rendering
-    /// and DisplayBrightness for the two-level dim control).
-    type DisplayDriver: DrawTarget<Color = BinaryColor> + DisplayBrightness;
+    /// Concrete display driver type. Each board's driver implements
+    /// [`BoardDisplay`] to render the splash + dashboard content into its
+    /// native pixel format and resolution and to flush / dim the panel.
+    type DisplayDriver: BoardDisplay;
 
     /// RGB LED driver. Boards without an LED use `()`.
     type LedDriver: RgbLed;