Per the Wio Tracker L1 schematic, it has a green LED on P1.01.
Moved SimpleLed from driver/ to board layer (esp32s3.rs and
wio_tracker_l1.rs) since the impl needs HAL-specific Output types.
Removed driver/simple_led.rs — each board layer defines its own.
RAK WisBlock remains LedDriver=() (no user LED on the core module).
- heltec_v3 now uses USB OTG (requires hardware mod: solder R29/R3)
- heltec_v3_uart added as fallback for stock boards
- Removed every #[allow(dead_code)] — fixed root causes instead:
- Comm types (UsbParts/UartParts) moved to individual board files
- USB/UART init removed from hal (boards call esp-hal directly)
- SH1106 driver gated on boards that use it
- UART task sends DisplayCommand::Reset at startup (variant now used)
- ErrorCode::CrcError removed (SX1262 drops bad-CRC silently)
- check/clippy now use --release (no more Xtensa dev-mode warnings)
- Updated README with hardware mod docs and board table
The default heltec_v3 feature now uses native USB OTG (same as V4),
appearing as /dev/ttyACM0 with the DongLoRa VID:PID (1209:5741).
This requires a hardware mod: solder R29/R3 and disconnect the CP2102
from the USB data lines.
Stock (unmodified) V3 boards should use the new heltec_v3_uart feature
which preserves the original UART-over-CP2102 behavior (/dev/ttyUSB0).
- heltec_v3: switched from UART to USB OTG
- heltec_v3_uart: new feature, UART fallback for stock boards
- Removed #[cfg] gates on UsbParts/UartParts (both always defined)
- Updated README with hardware mod instructions and board table
- Updated justfile with heltec_v3_uart board definition
- LoRaBoard trait now has associated types: RadioParts, CommParts, DisplayParts, DisplayDriver
- into_parts() is on the trait (enforced by compiler, not implicit convention)
- BoardParts<R, C, D> struct replaces tuple return from into_parts()
- mac_address() stays on trait, MAC also in BoardParts for convenience
- Removed mac field from DisplayParts (display task calls Board::mac_address())
- DisplayDriver associated type requires DrawTarget<Color = BinaryColor>
- Each board now exports DisplayDriver type and create_display() async fn
- ESP32-S3 boards share SSD1306 create_display in board/esp32s3.rs
- RAK WisBlock has its own SSD1306 create_display (different I2C type)
- Wio Tracker has SH1106 create_display (different display IC)
- Removed all cfg_if from display.rs — calls board::create_display()
- Removed display init retry logic (single attempt, return None on failure)
- ZERO board-specific #[cfg(feature)] outside board/, host/mod.rs, and hal/
- Flattened radio/ directory to radio.rs (was just one file)
- Flattened display/ to display.rs (combined task + rendering as inline module)
- Moved SH1106 display driver reference from display/ to driver/ (done in Phase 2)
- Suppressed dead_code warnings for conditional USB/UART types in hal
- All boards: zero warnings, zero cfg in application code
- Created hal/esp32s3.rs with MCU primitives (SPI, I2C, USB, UART, timer, MAC)
- Created hal/nrf52840.rs with shared nRF boilerplate (interrupts, bus wrapping, VBUS, MAC)
- Moved SH1106 OLED driver from display/ to driver/ (clear separation from app code)
- Board esp32s3.rs now delegates MCU init to hal, keeps only peripheral wiring (RadioParts)
- nRF board files use hal for shared StaticCell patterns, mac_address, interrupt bindings
- Board files still own pin assignments and peripheral construction
swaits