firmware/CHANGELOG.md

Changelog

All notable changes to this project will be documented in this file.

The format is based on Keep a Changelog, and this project adheres to Semantic Versioning.

[Unreleased]

[1.5.0] - 2026-04-30

Added

• Heltec Mesh Node T114 board support (nRF52840 + SX1262 + 1.14" 240×135 ST7789 color TFT). The first color display board in the project, and the third nRF52840 + SX1262 board alongside the RAK4631 and Wio Tracker L1.

  • VEXT_ENABLE (P0.21) driven HIGH at boot to power the SX1262 + TFT rail. Without this, lora-phy init succeeds at the SPI level but TX_DONE never fires.
  • VTFT_CTRL on P0.03 (active-LOW); PWM backlight on P0.15 (active-LOW, inverted) for smooth dim/bright transitions.
  • TFT SPI2 (SCK P1.08 / MOSI P1.09) at 8 MHz over EasyDMA, async ExclusiveDevice from embedded-hal-bus.
  • Linker uses the shared ld/nrf52840-memory.x so the S140 SoftDevice region (0x01000–0x26000) is preserved per project policy.

• BoardDisplay trait (src/display.rs) bundles render_*, present(), set_bright(), and set_dim(). Replaces the previous DrawTarget<Color = BinaryColor> + DisplayBrightness combo as the LoRaBoard::DisplayDriver bound, so each board renders in its native pixel format and resolution without aliasing or color-quantization round-trips. Existing mono OLED drivers (Sh1106, Ssd1306Async) get adapter impls that delegate to the existing display::render module — no behavior change for any previously supported board.

• Async ST7789 driver (src/driver/st7789.rs) wrapping lcd-async (async fork of mipidsi) with a 64,800-byte raw-byte framebuffer in .bss. Renders via lcd_async::raw_framebuf::RawFrameBuf<Rgb565, _> and presents via a single async DMA blit (panel.show_raw_data(...).await); the await yields the executor for the ~65 ms SPI transfer so the radio task isn't starved during repaints.

• Native 240×135 RGB565 renderer (src/display/render_color.rs) with splash, dashboard, and sparkline parity with the mono path, plus a shared QR-code blit (src/display/qr.rs) generic over PixelColor. The blit re-centers the 64×64 bitmap (cells in cols 0..50 with ~14 px right-side padding), so both mono and color splash now show the QR with 7 px quiet zones on all four sides (was visibly left-shifted on mono).

• Shared content types (BoardInfo, DashboardCtx) decouple what to draw from how each board renders it. create_display() now takes the board's full DisplayParts bundle (was just the I2C bus), so non-I2C displays can carry SPI + control pins through.

• IDF app descriptor on every ESP image. New esp-bootloader-esp-idf 0.5 dependency (chip-feature-gated like the rest of the esp-* stack) plus esp_app_desc!() in src/main.rs, which emits the .flash.appdesc section that espflash v4 requires in every ESP binary.

Changed

• ESP build modernized to upstream crates.io. Removed the [patch.crates-io] block that pinned esp-hal, esp-rtos, esp-backtrace, and esp-println to esp-rs/esp-hal#main. The versions tracked there (esp-hal 1.1, esp-rtos 0.3, esp-backtrace 0.19, esp-println 0.17) have all reached crates.io with the embassy-executor 0.10 compatibility we needed, so the local fork pins are no longer required. cargo:espflash bumped to v4 in mise.toml to match.

• hsmc 0.5.0 → 0.5.1. Patch bump pulled in transparently with the lockfile refresh; no behavior change.

• Documentation consolidated. PROTOCOL.md removed from the firmware repo (it now lives canonically in the spec repo, linked from README.md). BLE_MUX_DESIGN_DOC.md moved to docs/ble_mux_design.md so all firmware design docs sit under docs/.

[1.4.1] - 2026-04-29

Fixed

• Major LoRa reliability boost across every radio family. Switched lora-phy from crates.io to the swaits/lora-rs#fixed fork branch — a merge of three fixes awaiting upstream PR acceptance, pinned at e8a52ebd via Cargo.lock:

  • #428 — sx126x: pre-command BUSY check + standby/IRQ-clear hygiene around CAD.
  • #431 — sx127x: clear stale IRQ flags in do_rx before mode change.
  • #432 — sx127x: clear stale IRQ flags before reconfiguring DIO mapping in set_irq_params.

  Stability gain across the fleet: the sx126x BUSY-race fix lands on every nRF / RP2040 board, and the sx127x IRQ-clear fixes unblock the LilyGo T-Beam (classic) in particular.

• UART host RX delivery on UART-only boards. RADIO_THROTTLED was never cleared on UART (heltec_v3_uart, elecrow_thinknode_m2, lilygo_tbeam) — the throttle gate added in v1.3.0's chart-first restructure silently dropped every async RX from boot. Mirrored the USB pattern: clear the throttle on successful tx.write_all, re-arm on failure.

• UART host watchdog spurious-trip under saturated bidirectional load. The select3-based loop serialised read and write; tx.write_all (~25 ms per max frame at 115200 baud) blocked the read poll long enough for last_frame_at to age past 1000 ms, cascading a Reset to radio (Unconfigured) and display (splash) and leaving subsequent host TX commands timing out. Restructured host_task into two sub-loops joined in the same task: read_loop owns rx + watchdog, write_loop owns tx + throttle. Same executor, disjoint borrows on the split rx/tx halves, no Mutex needed. Also reset the FrameDecoder on watchdog fire so a host that resumes mid-frame resyncs cleanly on the next 0x00 sentinel (USB gets this for free via DTR-drop reset; UART has no DTR).

• Splash board-name overflow on long names. Names that don't fit FONT_6X10 (21 ASCII chars on a 128 px-wide OLED) now fall back to FONT_5X8 (25 chars). A const_assert at the BOARD_NAME definition rejects names that overflow even the fallback, so the board porter shortens NAME at compile time rather than getting silent overflow at runtime. Also dropped the URL-line font on the "learn more" screen from FONT_5X8 to FONT_4X6 so donglora.com sits inside the 64 px column with breathing room instead of touching both edges.

Changed

• hsmc 0.4 → 0.5. default(...) is optional on every state in 0.5; collapsed the WaitingForFirstFrame substate that existed only because 0.4 required Connected to declare a default child. Connected itself is now the resting "DTR up, no traffic yet" state, with on(FrameReceived) => Active descending into the inactivity-timer state on the first byte. Behavior is identical (entry/exit chain math unchanged); the host/usb chart has one fewer state and one fewer default(). Display and Radio charts left as-is — their defaults serve real grouping/lifecycle purposes, not 0.4 artifacts.
• ESP cross-toolchain pinned in mise.toml. [env] now owns the PATH (xtensa-esp-elf-gcc bin) and LIBCLANG_PATH, so any mise exec resolves the linker without sourcing espup's stray ~/export-esp.sh. New [tasks.esp-install] invokes espup with the matching crosstool version pin. cargo:espup pinned to 0.17.1 to match the [env] paths. Triggered by a real failure where ~/export-esp.sh was moved to Trash and the ESP build broke with linker xtensa-esp32s3-elf-gcc not found. Bumping ESP versions remains a two-touch change: edit version dirs in BOTH [tasks.esp-install] and [env].
• ESP dependency requirements bumped to track the upstream esp-rs/esp-hal main branch: esp-hal 1.0 → 1.1, esp-rtos 0.2 → 0.3, esp-backtrace 0.18 → 0.19, esp-println 0.16 → 0.17. cargo update had silently invalidated the [patch.crates-io] entries (the patched versions were no longer semver-compatible with the old top-level requirements), dropping the patches and falling back to crates.io releases that pin embassy-executor 0.9 — mismatched with our 0.10. Catching this keeps the patch suite consistent until the planned [patch.crates-io]-removal pass.

[1.4.0] - 2026-04-25

Added

• RAK4631 WisBlock board support (nRF52840 + SX1262, RAK19007 base

  • RAK4631 Core + RAK1921 OLED). The second nRF52840 + SX1262 board alongside the Wio Tracker L1.
  • SX126X_POWER_EN (P1.05) driven HIGH at init — the radio is power-gated on this module; without this the chip has no power and SPI hangs.
  • HFXO + LFXO external crystals selected in embassy_nrf::Config. USB CDC-ACM needs ±500 ppm which the internal RC oscillator can't provide.
  • SoftwareVbusDetect(true, true) so USB enumerates without a CLOCK_POWER interrupt handler.
  • Green LED on P1.03 (RAK19007 Base LED1, active-HIGH) via SimpleLed.
  • Hardware-validated end-to-end: ADVERT round-trip with an external receiver on US915.
  • Added debug-checkpoint blink-map coverage at every TX-phase boundary in radio.rs, including a new checkpoint between prepare_for_cad and cad() so future bring-ups can distinguish a modem-setup hang from a DIO1-wait hang.

• Adaptive listen-before-talk. The CAD pre-TX retry loop scales to the active LoRa config instead of running a fixed 10 retries × 10 ms (which was roughly one max-length packet at SF7/BW500 and a no-op at SF12/BW125).

  • Per-retry sleep is sized to the time-on-air of an assumed-peer 80-byte packet under the current SF/BW/CR — cached on RadioContext, recomputed on every SET_CONFIG.
  • Retry count = clamp(floor(BUDGET/T)+1, 1, 10) with BUDGET = 2.5 s. Fast configs still get up to 10 retries; SF11/12 degrade to single-CAD-and-bail (logged at config-apply).
  • Sleeps jittered ±20% per iteration to decorrelate simultaneously-backing-off contenders.
  • ToA math, CR→{1..4} mapping, retry-count derivation, and jitter helper live in a pure src/lbt.rs module — host-testable via DONGLORA_HOST_TEST=1 cargo test (13 tests).
  • Validated on-device: 20 iterations of the AI Bot test flow that previously saw ~2 ChannelBusy errors now sees zero at the same SF/BW.

Fixed

• First-TX-after-boot reliability on SX1262 boards. Picked up the upstream lora-phy fix that moves the BUSY-handshake check from after to before each SPI op, per Semtech SX1261/2 §8.3.1, LR1121 UM §3, and LR1110 DS §1.2.5. The existing post-op wait is preserved as the belt that closes the BUSY-assertion latency window (T_SW ≤ 600 ns) that a single level-poll can miss. Consumed via [patch.crates-io] against swaits/lora-rs#fix/sx126x-busy-race until the upstream PR merges.
  • Hardware-verified on Seeed Wio Tracker L1: 20/20 clean-boot TX (vs ~50% before).
  • Renames InterfaceVariant::wait_on_busy → wait_until_ready to match the new semantics.
• BUSY pin pull-down → none on nRF SX1262 boards. SX1262's BUSY pin has an internal 20 kΩ pull-up (datasheet p. 53); our Input::new(..., Pull::Down) was contending with it, leaving BUSY at an indeterminate voltage and intermittently mis-reading the chip's ready state. Per lora-rs/lora-rs#260, switched to Pull::None on both Wio Tracker L1 and RAK4631. The RAK4631 appeared to work before, but was affected by the same class of bug per the upstream issue — now deterministically correct rather than "happens to work".

Changed

• Build-system DX. just flash, just flash-probe, and just build accept an optional comma-separated extra_features argument that is appended to the board feature, e.g. just flash wio_tracker_l1 debug-checkpoint. No more dropping to raw cargo + rust-objcopy + uf2 cp for iteration loops.
• just recipes now resolve all tools through mise via set shell := ["mise", "exec", "--", "sh", "-c"]. cargo, espflash, rust-objcopy, cargo-hex-to-uf2 etc. always pick up the versions pinned in mise.toml regardless of PATH ordering.
• mise.toml rust pins now carry ARM targets + clippy, so a fresh mise install is sufficient bootstrapping — no manual rustup target add for thumbv6m-none-eabi / thumbv7em-none-eabihf and no separate clippy install.
• New just flash-dfu recipe for the Adafruit nRF52 bootloader (VID:PID 239a:0029) via adafruit-nrfutil under uvx, with port autodetect.
• Per-board _info chain in the justfile collapsed from a long per-board if/elif ladder + per-board := variables into a single case statement — one place per board, two lists (names + metadata).

[1.3.1] - 2026-04-23

Fixed

• LilyGo T-Beam (classic) red LED now flashes on TX/RX instead of dimming off. The red LED under the OLED is wired active-LOW on this board (anode to V+, cathode to GPIO4); v1.3.0 drove it as active-HIGH, so the LED sat lit at idle and briefly dimmed during activity.
  • Empirically verified on hardware against both T-Beam variants.
  • Introduces src/driver/inverted_pin.rs::InvertedPin<P>, a generic OutputPin wrapper that swaps set_high/set_low. Polarity is expressed at the pin (where the physical wiring lives), so SimpleLed stays polarity-agnostic and every other board's code path is byte-for-byte unchanged.
  • Classic T-Beam now constructs its LED as SimpleLed(InvertedPin(led_pin)) with pin init at Level::High (dark at boot).

[1.3.0] - 2026-04-23

Added

• LilyGo T-Beam S3 Supreme board support (ESP32-S3 + SX1262 + SH1106 OLED + AXP2101 PMIC, native USB-C).
  • Pin map verified against MeshCore's variants/lilygo_tbeam_supreme_SX1262.
  • New src/driver/axp.rs module with an AXP2101 init sequence (ALDO3 = 3.3 V LoRa, ALDO1 = 3.3 V OLED). The PMIC gates LoRa and display power — without it the SX1262 never responds on SPI.
  • PMIC lives on a dedicated I²C1 bus (SDA=42, SCL=41), separate from the SH1106 on I²C0 (SDA=17, SCL=18). I²C1 is used blocking for a one-shot init and then dropped.
  • TCXO driven at 1.6 V via DIO3 (MeshCore uses the same).
• LilyGo T-Beam (classic) board support (ESP32 + SX1276 + SSD1306 OLED + AXP192 PMIC, CP2102 USB-UART bridge). This is the first board in the firmware on classic ESP32 (non-S3) and the first on the SX127x radio family.
  • Pin map verified against MeshCore's variants/lilygo_tbeam_SX1276.
  • New src/hal/esp32.rs (classic-ESP32 MCU primitives, peripheral DMA via DMA_SPI2) and src/board/esp32.rs (SX1276 radio helper
    • SSD1306 display pipe).
  • AXP192 init added to src/driver/axp.rs: DCDC1 = 3.3 V for the OLED, LDO2 = 3.3 V for the SX1276 PA_BOOST rail. Shares the OLED I²C bus (SDA=21, SCL=22); the I²C instance is built in blocking mode for PMIC init and converted to async for the display task.
  • SX127x support via lora-phy 3's Sx127x<Sx1276> + GenericSx127xInterfaceVariant (DIO0 as the sole IRQ; no BUSY line on SX127x). XTAL clocked (no TCXO), tx_boost = true for the PA_BOOST path.
  • LoRaBoard trait gains supported_sf_bitmap() and supported_bw_bitmap() methods with SX126x defaults (0x1FE0, 0x03FF). T-Beam classic overrides SF to 0x1FC0 (SF6–SF12) — the SX1276 has no SF5.
  • radio_chip_id() reports 0x0011 (RadioChipId::Sx1276) and freq_range_hz() widens to 137 MHz–1020 MHz per the SX1276 datasheet.

Changed

• Cargo.toml: the esp32s3 chip feature has been moved out of the esp-hal / esp-rtos / esp-backtrace / esp-println dependency lines and into each ESP board's feature list (as esp-hal/esp32s3, etc.). This lets lilygo_tbeam select the classic esp32 chip flavour from the same dependency set.

[1.2.1] - 2026-04-23

Fixed

• Radio no longer drops to Idle mid-RX-session on transient failures. Extends the v1.1.0 invariant ("SET_CONFIG during RX auto-re-arms") to all failure paths that can occur while a client has RX active:

  • Receiving.on(RxFailed) => Idle now transitions to ResumingRx instead of Idle. A transient next_packet error re-arms the chip rather than ending the RX session.
  • TransmittingFromRx.on(TransmitFailed) => Idle now transitions to ResumingRx. TX failure during an active RX session returns TX_FAILED to the caller and resumes RX, matching the shape of the adjacent ChannelBusy handler.
  • ResumingRx.on(StartRxFailed) => Idle is now a bounded retry (5 × 25 ms backoff via a new bump_resume_retries action and a ResumeRxRetry / ResumeRxExhausted pair of internal events). The chip only lands in Idle after exhausting the retry budget — which means it's genuinely wedged and needs reconfiguring.

  Visible effect: the OLED dashboard no longer bounces to Splash when ai-bot (or any other client that TXes while RX is running) sends a packet. Previously any of the three transitions above would fire RadioEvent::Idle, which the display uses as its Dashboard → Splash trigger; the radio would land in Idle with no client aware enough to re-send RX_START, stranding the dashboard until the session was manually torn down and restarted.

• Removed announce_rx_failed helper action: its only purpose was emitting RadioEvent::Idle on the now-deleted Receiving.on(RxFailed) => Idle edge. No replacement needed — ResumingRx handles recovery silently.

[1.2.0] - 2026-04-22

Added

• OLED auto-dim after inactivity. The display is bright on any activity — splash entry, mode change into a dashboard leaf, packet RX/TX — and dims after a short idle window. Splash holds bright for 10 s, then drops to dim while the LearnMore / Info carousel keeps alternating. The dashboard stays bright for 3 s after the last packet or mode change, then dims in place without changing Listening/Transmitting state. Cross-leaf TX↔RX hops transition bright→bright with no intermediate dim — set_dim is fired as an action by the 3 s timer handler rather than as a sibling exit: action, so mode-change leaf-crossings never see a flash.
• DisplayBrightness trait in src/driver/mod.rs unifies the two-level backlight API across the ssd1306 crate's Ssd1306Async and the in-tree Sh1106 driver. Contrast values centralized as CONTRAST_BRIGHT (0xFF) and CONTRAST_DIM (0x08) constants so the two levels can be tuned in one place.

Changed

• src/display.rs statechart restructured:
  • Splash gains entry: set_bright plus an action-only on(after 10s) => set_dim handler so the splash bright window is time-scoped without disturbing the LM↔Info alternation.
  • Dashboard Listening and Transmitting each gain a nested *Bright substate owning the entry: set_bright action. Packet handlers moved into the leaves and target the leaf's *Bright — sibling-to-sibling within the leaf restarts the 3 s timer without re-entering the leaf itself (paint / 1 s sparkline timer preserved). The 3 s timeout handler fires set_dim as an action and up-transitions to the leaf, parking the machine at the leaf with no active child.
• On.on(CmdReset) now targets LearnMore directly rather than Splash. Under hsmc 0.2 up-transition semantics, targeting Splash from within Splash.LearnMore (USB-disconnect race path) would only unwind below Splash and park with no active child, leaving the LM↔Info alternation timer dead and the QR frozen on screen.
• LoRaBoard::DisplayDriver trait bound extended with + DisplayBrightness so brightness is part of the board contract alongside DrawTarget<Color = BinaryColor>.

Fixed

• Elecrow ThinkNode-M2 board doc corrected: the shipping revision carries a WCH CH340K USB-UART bridge (USB 1a86:7522), not a Silicon Labs CP2102. just flash elecrow_thinknode_m2 now matches the CH340K / CH340 VID:PIDs directly instead of falling through to espflash auto-detect.

Dependencies

• hsmc bumped to 0.2 to pick up the up-transition fix (transition to an already-active ancestor unwinds only the subtree strictly below the target; no exit/entry on the target; no default descent).

[1.1.0] - 2026-04-22

Small but high-value behavior change: SET_CONFIG issued while the radio is in continuous RX no longer drops the radio (and the OLED) back to idle. The radio now auto-re-arms RX with the new modulation once reconfiguration completes, matching DongLoRa Protocol 1.1's §3.5 / §6.3 amendments.

Changed

• src/radio.rs: inside state Receiving, add on(ConfigApplied) => ResumingRx to shadow the parent Configured state's on(ConfigApplied) => Idle handler. The reconfigure path now runs apply_set_config → ConfigApplied → ResumingRx.entry: try_start_rx_hw → StartRxOk → Receiving without ever entering Idle.
• The OLED's Dashboard → Splash transition was previously driven by RadioEvent::Idle firing on Configured.Idle.entry. That event no longer fires during a SET_CONFIG-from-Receiving sequence, so the display stays on Dashboard.

Dependencies

• donglora-protocol bumped to 1.1.0 (spec-only change; matches the new normative text the firmware now implements).

Use-case unlock

• Scanner / time-division / dynamic-modulation workflows that rotate LoRa parameters mid-RX no longer need to re-issue RX_START after every SET_CONFIG. One call, radio continues to receive.

[1.0.0] - 2026-04-22

The 1.0 release. Firmware now speaks DongLoRa Protocol v2 end to end, depends on the freshly-published donglora-protocol 1.0.0 and hsmc 0.1.0 from crates.io, and ships GitHub Release binaries for every supported board.

Breaking

• DongLoRa Protocol v2 wire format (wire-incompatible with 0.x clients and firmware). Every type_id, tag-correlation rule, and field layout follows PROTOCOL.md v1.0.
• Host framing replaced. src/host/framing.rs now drives a streaming FrameDecoder from donglora-protocol and emits (type_id, tag, payload) frames; the 0.x COBS-per-response shim is gone.
• Radio task reshape. src/radio.rs emits v2 TX_DONE / SetConfigResult / RxPayload / RxOrigin shapes directly; no 0.x translation layer remains.

Changed

• hsmc switched from path-dep on the local workspace to version = "0.1.0" from crates.io.
• donglora-protocol switched from path-dep on ../protocol to version = "1.0.0" from crates.io; firmware builds are now reproducible from a clean checkout with no sibling repo required.
• PROTOCOL.md updated to the DongLoRa Protocol v2 normative spec, kept byte-for-byte in sync with the donglora-protocol crate's copy.

Infrastructure

• Cargo.toml repository + homepage now point at the canonical https://github.com/donglora/firmware (the swaits/donglora repo is archived).

[0.5.0] - 2026-04-16

Added

• BLE soft-mesh multiplexer design document (BLE_MUX_DESIGN_DOC.md) — specification for turning a dongle from a 1:1 USB device into a shared near-field radio gateway for multiple BLE-attached phones. Three-phase rollout (v1 MVP, v2 hardening, v3 multi-dongle mesh) with regulatory duty-cycle and TX-access-control enforcement from v1. Targets nRF52840 first; ESP32-S3 reserved for v2.
• debug-checkpoint cargo feature with a dedicated debug_blink task and a latching atomic checkpoint — LED-pattern diagnostic for UART-only boards where defmt output would corrupt the host protocol. Zero footprint when the feature is off.

Changed

• Radio task rewritten as an hsmc statechart (Unconfigured / Configured.{Idle, StartingRx, Receiving, ResumingRx, Transmitting.{FromIdle, FromRx}}). The main loop is now a single machine.run().await; command reading, packet RX, and TX are state-scoped during: activities. Post-TX RX re-arm is modeled as state identity (TransmittingFromRx → ResumingRx) instead of a was_receiving flag.
• Display task rewritten as an hsmc statechart (Off / On.{Splash.{LearnMore, Info}, Dashboard.{Listening, Transmitting}}). The 5 s splash alternation and 1 s sparkline tick use on(after …) / on(every …) transitions — no external timer task.
• USB host task now carries a small hsmc statechart (Disconnected / Connected) whose entry/exit actions handle display wake, radio StopRx, and display reset — replacing the open-coded was_connected edge detector.
• Radio → Display channel switched from a RadioStatus watch to a typed RadioEvent queue. The radio emits discrete EnteredRx / EnteredTx / Idle / PacketRx / PacketTx / ConfigChanged events; downstream consumers observe transitions directly rather than diffing snapshots.
• Wire protocol types and COBS framing moved out of firmware into the shared donglora-protocol crate (path dep on ../protocol). Firmware src/protocol.rs is now a re-export shim preserving every call site; src/host/framing.rs keeps only the embassy-specific route_command.

Fixed

• USB disconnect recovery: on a read error the DTR-edge-detect branch now runs unconditionally (was early-continuing in some paths, starving the display-reset / radio-stop handoff).

[0.4.0] - 2026-04-11

Added

• ELECROW ThinkNode-M2 board support (ESP32-S3 + SX1262 + 1.3" SH1106 OLED via CP2102 UART bridge, 1000 mAh Li-Po handheld)
  • Pin map verified against Meshtastic's variants/esp32s3/ELECROW-ThinkNode-M2
  • DIO3 TCXO driven at 3.3 V (not 1.8 V like Heltec)
  • Dedicated LORA_POWER_EN (GPIO48) sequenced HIGH before SPI init
  • VEXT_ENABLE (GPIO46) is active HIGH — opposite polarity from Heltec
  • Reuses the existing async SH1106 driver at I2C address 0x3C

Changed

• hal::esp32s3::{init_spi, init_i2c} and board::esp32s3::init_radio are now generic over GPIO type, so ESP32-S3 boards with different pin assignments can share the helpers.
• board::esp32s3::init_radio takes a TcxoCtrlVoltage parameter instead of hardcoding Ctrl1V8 — needed for ThinkNode-M2's 3.3 V TCXO.
• SSD1306 display items in board::esp32s3 are now cfg-gated to Heltec boards (ThinkNode-M2 supplies its own SH1106 create_display).
• justfile uses cargo +esp for Xtensa targets instead of cargo +nightly with a RUSTC=esp override — the self-contained esp toolchain keeps its cargo, rustc, and rust-src versions aligned. Public nightly's rust-src had drifted ahead of the esp fork, breaking -Zbuild-std.
• Migrated to embassy-executor 0.10 and embassy-rp 0.10
• ESP crates (esp-hal, esp-rtos, esp-backtrace, esp-println) patched from esp-rs/esp-hal main branch until esp-rtos publishes with 0.10 support
• Adapted to embassy-executor 0.10 SpawnToken API (task functions now return Result<SpawnToken, SpawnError>, Spawner::spawn no longer returns Result)
• Adapted to esp-hal main branch API changes: efuse::base_mac_address(), esp_rtos::start now requires SoftwareInterrupt, embassy-rp SPI constructor now requires DMA interrupt bindings
• just check now runs clippy with -D warnings instead of plain cargo check
• Rust toolchain bumped to 1.94 in mise.toml

Fixed

• core::mem::forget(output) pattern in ESP32-S3 board files is now let _vext = Output::new(...) — current esp-hal makes Output non-Drop, which made forget a no-op and tripped clippy's forget_non_drop lint.
• UART boards (heltec_v3_uart) display stuck on splash screen after boot. Host task sent DisplayCommand::Reset (which sets disconnected=true) instead of DisplayCommand::On. UART has no DTR, so nothing ever cleared it.

[0.3.0] - 2026-04-10

Added

• Waveshare RP2040-LoRa board support (RP2040 + SX1262, no OLED, LED on GPIO25)
  • First RP2040 board — third MCU family after ESP32-S3 and nRF52840
  • New hal/rp2040.rs module with MCU primitives (SPI, USB, flash unique ID)
  • USB-C via FPC ribbon cable to adapter board
  • PE4259 antenna switch on GPIO17, 850-930 MHz (HF)

Changed

• cortex-m-rt/set-vtor moved from global dependency to per-board feature (Cortex-M0+ has no VTOR register)
• build.rs memory.x selection is now target-aware (thumbv6m vs thumbv7em)

[0.2.1] - 2026-04-07

Fixed

• Display stuck on status screen after USB disconnect (stale radio status updates re-rendered dashboard over splash because disconnected flag was not set in the Reset handler)
• Radio left running after host disconnect, now sends StopRx when DTR drops
• System deadlock when host app closes serial port while radio is receiving (unsolicited responses in radio task now use try_send to avoid blocking on a full response channel)
• LED orphaned if OLED display initialization fails (display task now falls back to a LED-only event loop instead of returning early)

[0.2.0] - 2026-04-07

Added

• Wio Tracker L1 board support (nRF52840 + SX1262, SH1106 OLED)
• LED blink on packet activity: brief flash on RX and TX when display is on
  • RX brightness scales with SNR (stronger signal = brighter)
  • Works on all boards with a user LED (Heltec V3/V4, Wio Tracker)
• Native USB CDC-ACM support for Heltec V3 (requires hardware mod: solder R29/R3)
• heltec_v3_uart feature for stock (unmodified) V3 boards via CP2102 bridge
• RgbLed trait and SimpleLed driver for GPIO-based LEDs
• LoRaBoard trait with full associated types (RadioParts, CommParts, DisplayParts, DisplayDriver, LedDriver) and BoardParts<R, C, D, L> struct

Changed

• Major firmware architecture reorganization:
  • hal/ module for MCU-specific primitives (ESP32-S3, nRF52840)
  • driver/ module for hardware peripheral drivers (SH1106, SimpleLed)
  • host/ module for unified USB/UART communication with internal cfg dispatch
  • board/ contains only board definitions — no MCU helpers or drivers mixed in
  • Board files are declarative wiring diagrams calling hal primitives
• run() function has zero board-specific conditional compilation
• Display init moved to board layer (create_display()) — display task has no cfg
• Flattened radio/ and display/ directories (no single-file directories)
• build.rs auto-discovers boards by content (implements LoRaBoard) and helper modules by use super:: imports — no exclusion lists
• check and clippy commands now use --release profile
• Deduplicated USB/UART protocol framing (shared CobsDecoder + route_command)
• Removed ErrorCode::CrcError (SX1262 silently drops bad-CRC packets)

Fixed

• Display stuck on splash screen for UART boards (disconnected flag started true)

[0.1.0] - 2026-03-15

Added

• Transparent LoRa radio over USB CDC-ACM (VID 1209, PID 5741)
• COBS-framed fixed-size LE binary protocol (9 commands, 7 responses)
• Radio configuration: frequency, bandwidth, spreading factor, coding rate, TX power
• Continuous RX mode with RSSI/SNR per packet
• Single-shot TX with optional per-packet config override
• SSD1306 OLED display support with status dashboard
  • Radio state, frequency, modulation parameters
  • Packet counters (RX/TX)
  • RSSI sparkline (1-minute history, TX shown as dotted bars)
  • Combined splash/waiting screen on disconnect
• Auto-detect USB host connect/disconnect via DTR
• Config validation against per-board hardware limits
• TX_POWER_MAX sentinel (-128): auto-use the board's maximum TX power
• Board support: Heltec V3, Heltec V4, RAK WisBlock 4631
• Python host library (donglora on PyPI) with pip install and donglora-mux CLI
• USB multiplexer for sharing one dongle with multiple applications
• Two-way LoRa bridge over TCP (examples/lora_bridge.py)

Technical

• Embassy async runtime (no threads, CPU sleeps when idle)
• Zero-config: boots and waits for host commands
• Protocol-agnostic: firmware has no opinion about what you transmit
• Tasks never panic: all errors reported to host or logged
• Board abstraction: one .rs file + one Cargo feature per board