diff --git a/clients/rust/CLAUDE_TODO.md b/clients/rust/CLAUDE_TODO.md
new file mode 100644
index 00000000..7fa5ebc3
--- /dev/null
+++ b/clients/rust/CLAUDE_TODO.md
@@ -0,0 +1,86 @@
+# Add non-blocking `connect` variant
+
+## Problem
+
+`connect(None, timeout)` in `src/connect.rs` has a three-step fallback:
+
+1. `DONGLORA_MUX_TCP` env var -> TCP mux
+2. Unix socket mux (if socket file exists)
+3. Direct USB serial via `find_port().unwrap_or_else(wait_for_device)`
+
+Step 3 calls `wait_for_device()` which polls `find_port()` every 500ms
+**indefinitely** until a USB device appears. This makes `connect(None, ...)`
+unsuitable for callers that need to retry with backoff or report disconnected
+status (e.g. donglora-bridge's reconnect loop).
+
+Today, donglora-bridge works around this by manually reimplementing the
+fallback chain:
+
+```rust
+if let Ok(c) = connect_mux_auto(timeout) {
+    (c, "mux".to_string())
+} else {
+    let port_path = find_port()
+        .ok_or_else(|| anyhow!("no mux or USB dongle found"))?;
+    let c = connect(Some(&port_path), timeout)?;
+    (c, shorten_path(&port_path))
+}
+```
+
+This duplicates logic from `connect()` (steps 1-2 via `connect_mux_auto`, step
+3 minus the blocking wait) and won't pick up any future changes to the
+`connect()` fallback order.
+
+## Proposed solution
+
+Add a `try_connect` (or similar) that runs the same mux -> serial fallback as
+`connect(None, timeout)` but replaces `wait_for_device()` with a single
+`find_port()` call, returning an error immediately if no device is found:
+
+```rust
+/// Like [`connect`] but returns an error instead of blocking when no USB
+/// device is present. Suitable for callers with their own retry logic.
+pub fn try_connect(timeout: Duration) -> Result<Client<AnyTransport>> {
+    // Steps 1-2: identical to connect() — try TCP mux, then Unix socket mux
+
+    // Step 3: non-blocking USB scan
+    let port_path = discovery::find_port()
+        .ok_or_else(|| anyhow!("no DongLoRa device found (no mux, no USB device)"))?;
+    let transport = SerialTransport::open(&port_path, timeout)?;
+    Ok(Client::new(AnyTransport::Serial(transport)))
+}
+```
+
+This would let donglora-bridge collapse its connection code to:
+
+```rust
+let (mut client, device) = if let Some(port) = port {
+    let c = connect(Some(port), timeout)?;
+    (c, shorten_path(port))
+} else {
+    let c = try_connect(timeout)?;
+    let device = match c.transport() {
+        AnyTransport::Mux(_) => "mux".to_string(),
+        AnyTransport::Serial(_) => find_port()
+            .map(|p| shorten_path(&p))
+            .unwrap_or_else(|| "serial".to_string()),
+    };
+    (c, device)
+};
+```
+
+### Device name from transport
+
+The bridge also needs to know *what* it connected to for display purposes. Two
+options:
+
+1. Match on `AnyTransport` variant after connecting (shown above) -- works but
+   requires a redundant `find_port()` call for the display name since
+   `SerialTransport` has private fields.
+2. Have `try_connect` return the port path alongside the client, e.g.
+   `-> Result<(Client<AnyTransport>, ConnectionInfo)>` where `ConnectionInfo`
+   is an enum like `Mux { socket_path }` | `Serial { port_path }`. Cleaner
+   but a larger API change.
+
+Either works. Option 2 would also benefit `connect()` callers who want to log
+what they connected to.
diff --git a/firmware/.cargo/config.toml b/firmware/.cargo/config.toml
index 0ed53177..67b24524 100644
--- a/firmware/.cargo/config.toml
+++ b/firmware/.cargo/config.toml
@@ -4,3 +4,9 @@ rustflags = [
     "-C", "link-arg=-Wl,-Tdefmt.x",
     "-C", "link-arg=-nostartfiles",
 ]
+
+[target.thumbv7em-none-eabihf]
+rustflags = [
+    "-C", "link-arg=-Tlink.x",
+    "-C", "link-arg=-Tdefmt.x",
+]
diff --git a/firmware/Cargo.lock b/firmware/Cargo.lock
index 2b818bdb..ddb4ae30 100644
--- a/firmware/Cargo.lock
+++ b/firmware/Cargo.lock
@@ -111,6 +111,7 @@ checksum = "8ec610d8f49840a5b376c69663b6369e71f4b34484b9b2eb29fb918d92516cb9"
 dependencies = [
  "bare-metal",
  "bitfield 0.13.2",
+ "critical-section",
  "embedded-hal 0.2.7",
  "volatile-register",
 ]
@@ -301,6 +302,16 @@ dependencies = [
  "thiserror",
 ]
 
+[[package]]
+name = "defmt-rtt"
+version = "1.1.0"
+source = "registry+https://github.com/rust-lang/crates.io-index"
+checksum = "93d5a25c99d89c40f5676bec8cefe0614f17f0f40e916f98e345dae941807f9e"
+dependencies = [
+ "critical-section",
+ "defmt 1.0.1",
+]
+
 [[package]]
 name = "delegate"
 version = "0.13.5"
@@ -364,9 +375,11 @@ name = "donglora"
 version = "0.1.0"
 dependencies = [
  "cfg-if",
+ "cortex-m",
  "cortex-m-rt",
  "critical-section",
  "defmt 1.0.1",
+ "defmt-rtt",
  "display-interface",
  "embassy-embedded-hal 0.6.0",
  "embassy-executor",
diff --git a/firmware/Cargo.toml b/firmware/Cargo.toml
index c282f688..557ecfe3 100644
--- a/firmware/Cargo.toml
+++ b/firmware/Cargo.toml
@@ -62,7 +62,9 @@ esp-rtos = { version = "0.2", optional = true, features = [
 ] }
 
 # nRF52840 (RAK 4631)
-cortex-m-rt = { version = "0.7", optional = true }
+cortex-m = { version = "0.7", optional = true, features = ["critical-section-single-core"] }
+cortex-m-rt = { version = "0.7", optional = true, features = ["set-vtor"] }
+defmt-rtt = { version = "1.0", optional = true }
 embassy-nrf = { version = "0.10", optional = true, features = [
   "nrf52840",
   "gpiote",
@@ -89,7 +91,18 @@ heltec_v4 = [
   "dep:esp-rtos",
 ]
 rak_wisblock_4631 = [
+  "dep:cortex-m",
   "dep:cortex-m-rt",
+  "dep:defmt-rtt",
+  "dep:embassy-nrf",
+  "dep:panic-probe",
+  "embassy-executor/arch-cortex-m",
+  "embassy-executor/executor-thread",
+]
+wio_tracker_l1 = [
+  "dep:cortex-m",
+  "dep:cortex-m-rt",
+  "dep:defmt-rtt",
   "dep:embassy-nrf",
   "dep:panic-probe",
   "embassy-executor/arch-cortex-m",
diff --git a/firmware/build.rs b/firmware/build.rs
index 87bdc4c8..3d94ff8f 100644
--- a/firmware/build.rs
+++ b/firmware/build.rs
@@ -50,8 +50,7 @@ fn main() {
     }
 
     let mut env = Environment::new();
-    let template =
-        fs::read_to_string("src/board/mod.rs.j2").expect("missing src/board/mod.rs.j2");
+    let template = fs::read_to_string("src/board/mod.rs.j2").expect("missing src/board/mod.rs.j2");
     env.add_template("mod", &template)
         .expect("failed to parse board template");
     let rendered = env
@@ -63,4 +62,17 @@ fn main() {
 
     println!("cargo:rerun-if-changed=src/board/mod.rs.j2");
     println!("cargo:rerun-if-changed={}", board_dir);
+
+    // cortex-m-rt's link.x does `INCLUDE memory.x`. Copy our nRF layout into
+    // OUT_DIR (which cortex-m-rt already adds to the linker search path) so it's
+    // only visible to ARM builds. Keeping it out of the project root prevents
+    // the linker from shadowing esp-hal's generated memory.x on Xtensa builds.
+    let target = std::env::var("TARGET").unwrap_or_default();
+    if !target.starts_with("xtensa") {
+        let out_dir = std::env::var("OUT_DIR").unwrap();
+        fs::copy("ld/nrf52840-memory.x", format!("{out_dir}/memory.x"))
+            .expect("failed to copy ld/nrf52840-memory.x");
+        println!("cargo:rustc-link-search={out_dir}");
+    }
+    println!("cargo:rerun-if-changed=ld/nrf52840-memory.x");
 }
diff --git a/firmware/justfile b/firmware/justfile
index 3f2e1b37..24e3d855 100644
--- a/firmware/justfile
+++ b/firmware/justfile
@@ -6,11 +6,12 @@ set shell := ["bash", "-c"]
 heltec_v3 := "heltec_v3 xtensa-esp32s3-none-elf esp32s3"
 heltec_v4 := "heltec_v4 xtensa-esp32s3-none-elf esp32s3"
 rak_wisblock_4631  := "rak_wisblock_4631 thumbv7em-none-eabihf nRF52840_xxAA"
+wio_tracker_l1     := "wio_tracker_l1 thumbv7em-none-eabihf nRF52840_xxAA"
 
 builds_dir := "builds"
 
 # All known boards
-boards := "heltec_v3 heltec_v4 rak_wisblock_4631"
+boards := "heltec_v3 heltec_v4 rak_wisblock_4631 wio_tracker_l1"
 
 # Install all required tools and toolchains
 setup:
@@ -65,7 +66,7 @@ build board profile="release":
     @just _cargo {{board}} "build --{{profile}}"
     @just _copy_firmware {{board}} {{profile}}
 
-# Build and flash a board (espflash for Xtensa, probe-rs for ARM)
+# Build and flash a board (espflash for Xtensa, UF2 DFU for ARM)
 flash board:
     @just _ensure_tools
     @just build {{board}} release
@@ -80,9 +81,16 @@ flash board:
                 echo "No port found, falling back to espflash auto-detection..." >&2; \
                 espflash flash "{{builds_dir}}/donglora-{{board}}-release.elf"; \
             fi ;; \
-        *) probe-rs run --chip $chip "{{builds_dir}}/donglora-{{board}}-release.elf" ;; \
+        *) just _flash_uf2 {{board}} ;; \
     esac
 
+# Flash ARM board via debug probe (requires J-Link or similar)
+flash-probe board:
+    @just _ensure_tools
+    @just build {{board}} release
+    @read -r feat target chip <<< "$(just _info {{board}})"; \
+    probe-rs run --chip $chip "{{builds_dir}}/donglora-{{board}}-release.elf"
+
 # Show binary size for a release build
 size board:
     @just _cargo {{board}} "size --release"
@@ -163,11 +171,38 @@ _copy_firmware board profile:
     @read -r feat target chip <<< "$(just _info {{board}})"; \
     src="target/$target/{{profile}}/donglora"; \
     dst="{{builds_dir}}/donglora-{{board}}-{{profile}}"; \
-    if [ -f "$src" ]; then cp "$src" "$dst.elf"; echo "→ $dst.elf"; fi
+    if [ -f "$src" ]; then \
+        cp "$src" "$dst.elf"; echo "→ $dst.elf"; \
+        case "$target" in \
+            thumbv7em-*) \
+                mise exec -- rust-objcopy -O ihex "$src" "$dst.hex"; \
+                mise exec -- cargo-hex-to-uf2 hex-to-uf2 --input-path "$dst.hex" --output-path "$dst.uf2" --family nrf52840; \
+                rm "$dst.hex"; \
+                echo "→ $dst.uf2"; \
+                ;; \
+        esac; \
+    fi
+
+# Copy UF2 to a mounted UF2 bootloader drive
+[private]
+_flash_uf2 board:
+    @uf2="{{builds_dir}}/donglora-{{board}}-release.uf2"; \
+    if [ ! -f "$uf2" ]; then \
+        echo "error: $uf2 not found — run 'just build {{board}}' first" >&2; exit 1; \
+    fi; \
+    mnt="$(find /run/media -maxdepth 3 -name INFO_UF2.TXT -printf '%h\n' -quit 2>/dev/null)"; \
+    if [ -z "$mnt" ]; then \
+        echo "error: no UF2 drive found — double-tap reset to enter bootloader" >&2; exit 1; \
+    fi; \
+    echo "Copying to $mnt ..."; \
+    cp "$uf2" "$mnt/"; \
+    sync; \
+    echo "Done — board will reboot automatically"
 
 [private]
 _info name:
     @if [ "{{name}}" == "heltec_v3" ]; then echo "{{heltec_v3}}"; \
      elif [ "{{name}}" == "heltec_v4" ]; then echo "{{heltec_v4}}"; \
      elif [ "{{name}}" == "rak_wisblock_4631" ]; then echo "{{rak_wisblock_4631}}"; \
+     elif [ "{{name}}" == "wio_tracker_l1" ]; then echo "{{wio_tracker_l1}}"; \
      else echo "Unknown board: {{name}}" >&2; exit 1; fi
diff --git a/firmware/ld/nrf52840-memory.x b/firmware/ld/nrf52840-memory.x
new file mode 100644
index 00000000..8de03147
--- /dev/null
+++ b/firmware/ld/nrf52840-memory.x
@@ -0,0 +1,16 @@
+/* nRF52840 memory layout — Adafruit UF2 bootloader
+ *
+ *   0x00000 – 0x01000   MBR (Master Boot Record)
+ *   0x01000 – 0xEA000   Application  ← we live here
+ *   0xEA000 – 0xF4000   Reserved (app data)
+ *   0xF4000 – 0xFC000   UF2 Bootloader
+ *   0xFF000 – 0x100000  Bootloader settings
+ *
+ * RAM: first 8 bytes reserved for MBR interrupt forwarding.
+ */
+
+MEMORY
+{
+  FLASH : ORIGIN = 0x00001000, LENGTH = 0xE9000
+  RAM   : ORIGIN = 0x20000008, LENGTH = 255K
+}
diff --git a/firmware/mise.toml b/firmware/mise.toml
index 43fd002e..2e61d348 100644
--- a/firmware/mise.toml
+++ b/firmware/mise.toml
@@ -3,6 +3,7 @@ rust = "1.93"
 just = "latest"
 
 "cargo:cargo-binutils" = "latest"   # `cargo size`, `cargo objdump`, etc.
+"cargo:cargo-hex-to-uf2" = "latest" # ELF → UF2 via Intel HEX for nRF52840 DFU
 "cargo:espup" = "0.16"
 "cargo:espflash" = "3"              # 4.x has broken nix dependency on current stable Rust
 "cargo:probe-rs-tools" = "0.31"
diff --git a/firmware/src/board/heltec_v3.rs b/firmware/src/board/heltec_v3.rs
index 5a55fb36..031bd3bc 100644
--- a/firmware/src/board/heltec_v3.rs
+++ b/firmware/src/board/heltec_v3.rs
@@ -37,8 +37,7 @@ impl Board {
         core::mem::forget(vext); // hold pin low permanently; drop would reset it
 
         let radio = esp32s3::init_radio(
-            p.SPI2, p.DMA_CH0, p.GPIO9, p.GPIO10, p.GPIO11, p.GPIO8, p.GPIO12, p.GPIO14,
-            p.GPIO13,
+            p.SPI2, p.DMA_CH0, p.GPIO9, p.GPIO10, p.GPIO11, p.GPIO8, p.GPIO12, p.GPIO14, p.GPIO13,
         );
         let usb = esp32s3::init_usb(p.USB0, p.GPIO20, p.GPIO19);
         let i2c = esp32s3::init_display_i2c(p.I2C0, p.GPIO17, p.GPIO18);
diff --git a/firmware/src/board/heltec_v4.rs b/firmware/src/board/heltec_v4.rs
index 95c1b6b5..8e9c1150 100644
--- a/firmware/src/board/heltec_v4.rs
+++ b/firmware/src/board/heltec_v4.rs
@@ -37,8 +37,7 @@ impl Board {
         core::mem::forget(vext); // hold pin low permanently; drop would reset it
 
         let radio = esp32s3::init_radio(
-            p.SPI2, p.DMA_CH0, p.GPIO9, p.GPIO10, p.GPIO11, p.GPIO8, p.GPIO12, p.GPIO14,
-            p.GPIO13,
+            p.SPI2, p.DMA_CH0, p.GPIO9, p.GPIO10, p.GPIO11, p.GPIO8, p.GPIO12, p.GPIO14, p.GPIO13,
         );
 
         // Note: switches internal USB PHY from Serial-JTAG to OTG.
diff --git a/firmware/src/board/rak_wisblock_4631.rs b/firmware/src/board/rak_wisblock_4631.rs
index eb8cab55..d0671f5b 100644
--- a/firmware/src/board/rak_wisblock_4631.rs
+++ b/firmware/src/board/rak_wisblock_4631.rs
@@ -87,7 +87,6 @@ impl super::traits::LoRaBoard for Board {
 }
 
 impl Board {
-
     pub fn into_parts(self) -> (RadioParts, UsbParts, Option<DisplayParts>) {
         let p = self.p;
 
@@ -108,7 +107,8 @@ impl Board {
         let dio1 = Input::new(p.P1_15, Pull::Down);
         let busy = Input::new(p.P1_14, Pull::Down);
 
-        let iv = GenericSx126xInterfaceVariant::new(reset, dio1, busy, None, None).expect("SX1262 interface init");
+        let iv = GenericSx126xInterfaceVariant::new(reset, dio1, busy, None, None)
+            .expect("SX1262 interface init");
 
         let sx_config = sx126x::Config {
             chip: Sx1262,
@@ -125,7 +125,9 @@ impl Board {
         // ── USB ──────────────────────────────────────────────────
         static VBUS: StaticCell<embassy_nrf::usb::vbus_detect::SoftwareVbusDetect> =
             StaticCell::new();
-        let vbus = VBUS.init(embassy_nrf::usb::vbus_detect::SoftwareVbusDetect::new(true, false));
+        let vbus = VBUS.init(embassy_nrf::usb::vbus_detect::SoftwareVbusDetect::new(
+            true, false,
+        ));
         let usb = UsbParts {
             driver: Driver::new(p.USBD, Irqs, vbus),
         };
diff --git a/firmware/src/board/wio_tracker_l1.rs b/firmware/src/board/wio_tracker_l1.rs
new file mode 100644
index 00000000..3add31a0
--- /dev/null
+++ b/firmware/src/board/wio_tracker_l1.rs
@@ -0,0 +1,154 @@
+use embassy_embedded_hal::shared_bus::asynch::spi::SpiDevice;
+use embassy_nrf::gpio::{Input, Level, Output, OutputDrive, Pull};
+use embassy_nrf::spim::{self, Spim};
+use embassy_nrf::twim::{self, Twim};
+use embassy_nrf::usb::Driver;
+use embassy_nrf::{bind_interrupts, Peripherals};
+use embassy_sync::blocking_mutex::raw::NoopRawMutex;
+use embassy_time::Delay;
+use static_cell::StaticCell;
+
+use lora_phy::iv::GenericSx126xInterfaceVariant;
+use lora_phy::sx126x::{self, Sx1262, Sx126x};
+
+use super::traits::LoRaBoard;
+
+bind_interrupts!(struct Irqs {
+    USBD => embassy_nrf::usb::InterruptHandler<embassy_nrf::peripherals::USBD>;
+    SPIM3 => embassy_nrf::spim::InterruptHandler<embassy_nrf::peripherals::SPI3>;
+    TWISPI0 => embassy_nrf::twim::InterruptHandler<embassy_nrf::peripherals::TWISPI0>;
+});
+
+// ── Concrete peripheral types ────────────────────────────────────────
+
+type SpiBus = Spim<'static>;
+type Nss = Output<'static>;
+type Iv = GenericSx126xInterfaceVariant<Output<'static>, Input<'static>>;
+type RadioSpiDevice = SpiDevice<'static, NoopRawMutex, SpiBus, Nss>;
+/// SX126x driver (pre-LoRa construction — LoRa::new is async).
+pub type RadioDriver = Sx126x<RadioSpiDevice, Iv, Sx1262>;
+
+/// USB driver for CDC-ACM.
+pub type UsbDriver = Driver<'static, &'static embassy_nrf::usb::vbus_detect::SoftwareVbusDetect>;
+
+/// I2C bus for SH1106 OLED.
+pub type DisplayI2c = Twim<'static>;
+
+// ── Peripheral bundles ───────────────────────────────────────────────
+
+pub struct RadioParts {
+    pub driver: RadioDriver,
+    pub delay: Delay,
+}
+
+pub struct UsbParts {
+    pub driver: UsbDriver,
+}
+
+pub struct DisplayParts {
+    pub i2c: DisplayI2c,
+    pub mac: [u8; 6],
+}
+
+// ── Board init ───────────────────────────────────────────────────────
+
+pub struct Board {
+    p: Peripherals,
+}
+
+impl super::traits::LoRaBoard for Board {
+    const NAME: &'static str = "Wio Tracker L1";
+    const TX_POWER_RANGE: (i8, i8) = (-9, 22);
+
+    fn init() -> Self {
+        let mut config = embassy_nrf::config::Config::default();
+        config.hfclk_source = embassy_nrf::config::HfclkSource::ExternalXtal;
+        config.lfclk_source = embassy_nrf::config::LfclkSource::ExternalXtal;
+        let p = embassy_nrf::init(config);
+        Self { p }
+    }
+
+    fn mac_address() -> [u8; 6] {
+        // SAFETY: 0x10000000 is the nRF52840 FICR (Factory Information Configuration
+        // Registers) base address. Offsets 0x0A4 and 0x0A8 are the DEVICEADDR[0] and
+        // DEVICEADDR[1] registers containing the factory-programmed device address.
+        // read_volatile is correct for memory-mapped hardware registers.
+        unsafe {
+            let ficr = 0x10000000 as *const u32;
+            let addr0 = core::ptr::read_volatile(ficr.byte_add(0x0A4));
+            let addr1 = core::ptr::read_volatile(ficr.byte_add(0x0A8));
+            [
+                addr0 as u8,
+                (addr0 >> 8) as u8,
+                (addr0 >> 16) as u8,
+                (addr0 >> 24) as u8,
+                addr1 as u8,
+                (addr1 >> 8) as u8,
+            ]
+        }
+    }
+}
+
+impl Board {
+    pub fn into_parts(self) -> (RadioParts, UsbParts, Option<DisplayParts>) {
+        let p = self.p;
+
+        // ── SPI bus for SX1262 ───────────────────────────────────
+        let mut spi_cfg = spim::Config::default();
+        spi_cfg.frequency = spim::Frequency::M1;
+        let spi = Spim::new(p.SPI3, Irqs, p.P0_30, p.P0_03, p.P0_28, spi_cfg);
+
+        static SPI_BUS: StaticCell<embassy_sync::mutex::Mutex<NoopRawMutex, SpiBus>> =
+            StaticCell::new();
+        let spi_bus = SPI_BUS.init(embassy_sync::mutex::Mutex::new(spi));
+
+        let nss = Output::new(p.P1_14, Level::High, OutputDrive::Standard);
+        let spi_device = SpiDevice::new(spi_bus, nss);
+
+        // ── SX1262 control pins ──────────────────────────────────
+        let reset = Output::new(p.P1_07, Level::High, OutputDrive::Standard);
+        let dio1 = Input::new(p.P0_07, Pull::Down);
+        let busy = Input::new(p.P1_10, Pull::Down);
+
+        // RF switch: RXEN on P1.08 (GPIO, toggled by lora_phy), TX via DIO2 (SX1262 internal).
+        let rx_enable = Output::new(p.P1_08, Level::Low, OutputDrive::Standard);
+        let iv = GenericSx126xInterfaceVariant::new(reset, dio1, busy, Some(rx_enable), None)
+            .expect("SX1262 interface init");
+
+        let sx_config = sx126x::Config {
+            chip: Sx1262,
+            tcxo_ctrl: Some(sx126x::TcxoCtrlVoltage::Ctrl1V8),
+            use_dcdc: true,
+            rx_boost: false,
+        };
+
+        let radio = RadioParts {
+            driver: Sx126x::new(spi_device, iv, sx_config),
+            delay: Delay,
+        };
+
+        // ── USB ──────────────────────────────────────────────────
+        static VBUS: StaticCell<embassy_nrf::usb::vbus_detect::SoftwareVbusDetect> =
+            StaticCell::new();
+        let vbus = VBUS.init(embassy_nrf::usb::vbus_detect::SoftwareVbusDetect::new(
+            true, true,
+        ));
+        let usb = UsbParts {
+            driver: Driver::new(p.USBD, Irqs, vbus),
+        };
+
+        // ── BAT_CTL: P0.04, active HIGH — enables power to OLED and battery sense
+        let bat_ctl = Output::new(p.P0_04, Level::High, OutputDrive::Standard);
+        core::mem::forget(bat_ctl);
+
+        // ── Display (SH1106 OLED on I2C) ─────────────────────────
+        static TWIM_BUF: StaticCell<[u8; 256]> = StaticCell::new();
+        let twim_buf = TWIM_BUF.init([0u8; 256]);
+        let i2c_cfg = twim::Config::default();
+        let i2c = Twim::new(p.TWISPI0, Irqs, p.P0_06, p.P0_05, i2c_cfg, twim_buf);
+        let mac = Self::mac_address();
+        let display = Some(DisplayParts { i2c, mac });
+
+        (radio, usb, display)
+    }
+}
diff --git a/firmware/src/display/mod.rs b/firmware/src/display/mod.rs
index 50b4bdf1..bb78536d 100644
--- a/firmware/src/display/mod.rs
+++ b/firmware/src/display/mod.rs
@@ -1,5 +1,6 @@
 //! OLED display driver with radio status dashboard.
 
 mod render;
+pub mod sh1106;
 mod task;
 pub use task::display_task;
diff --git a/firmware/src/display/render.rs b/firmware/src/display/render.rs
index 034e0275..2c3145d2 100644
--- a/firmware/src/display/render.rs
+++ b/firmware/src/display/render.rs
@@ -69,10 +69,13 @@ pub fn dashboard(
     match status.state {
         RadioState::Receiving => {
             // "RX" inverted on row 0
-            Rectangle::new(Point::new(0, 0), Size::new(MODE_BOX_W as u32, FONT_H as u32))
-                .into_styled(fill)
-                .draw(target)
-                .ok();
+            Rectangle::new(
+                Point::new(0, 0),
+                Size::new(MODE_BOX_W as u32, FONT_H as u32),
+            )
+            .into_styled(fill)
+            .draw(target)
+            .ok();
             Text::new("RX", Point::new(1, FONT_H - 1), inv_style)
                 .draw(target)
                 .ok();
@@ -217,10 +220,7 @@ pub fn dashboard(
 }
 
 /// Render the splash/waiting screen (shown when idle or no config).
-pub fn splash(
-    target: &mut impl DrawTarget<Color = BinaryColor>,
-    board: &BoardInfo,
-) {
+pub fn splash(target: &mut impl DrawTarget<Color = BinaryColor>, board: &BoardInfo) {
     let bb = target.bounding_box();
     let w = bb.size.width as i32;
 
@@ -324,11 +324,8 @@ fn rssi_sparkline(
             i + committed.saturating_sub(effective_bars)
         } else {
             let start = count - RSSI_HISTORY_LEN;
-            let skip = RSSI_HISTORY_LEN.saturating_sub(if live {
-                visible_bars - 1
-            } else {
-                visible_bars
-            });
+            let skip =
+                RSSI_HISTORY_LEN.saturating_sub(if live { visible_bars - 1 } else { visible_bars });
             (start + skip + i) % RSSI_HISTORY_LEN
         };
         let is_tx = tx_history[idx];
@@ -361,7 +358,11 @@ fn bar_height(rssi: i16, is_tx: bool, spark_h: i32) -> Option<i32> {
         let clamped = rssi.clamp(RSSI_MIN, RSSI_MAX);
         ((clamped - RSSI_MIN) as i32 * spark_h) / (RSSI_MAX - RSSI_MIN) as i32
     };
-    if h == 0 { None } else { Some(h) }
+    if h == 0 {
+        None
+    } else {
+        Some(h)
+    }
 }
 
 /// Draw a single sparkline bar (solid for RX, dotted for TX).
diff --git a/firmware/src/display/sh1106.rs b/firmware/src/display/sh1106.rs
new file mode 100644
index 00000000..7216e8d8
--- /dev/null
+++ b/firmware/src/display/sh1106.rs
@@ -0,0 +1,136 @@
+//! Minimal async SH1106 I2C OLED driver (128x64, page addressing).
+//!
+//! The SH1106 is very similar to the SSD1306 but only supports page-mode
+//! addressing (no horizontal/vertical auto-advance). This driver sends
+//! framebuffer data page-by-page with explicit page/column commands.
+
+use embedded_graphics::draw_target::DrawTarget;
+use embedded_graphics::geometry::{OriginDimensions, Size};
+use embedded_graphics::pixelcolor::BinaryColor;
+use embedded_graphics::Pixel;
+use embedded_hal_async::i2c::I2c;
+
+const WIDTH: usize = 128;
+const HEIGHT: usize = 64;
+const PAGES: usize = HEIGHT / 8;
+const BUF_SIZE: usize = WIDTH * PAGES; // 1024
+
+/// SH1106 has a 132-column RAM; visible 128 columns are centered with a
+/// 2-column offset on each side.
+const COL_OFFSET: u8 = 2;
+
+pub struct Sh1106<I> {
+    i2c: I,
+    addr: u8,
+    buffer: [u8; BUF_SIZE],
+}
+
+impl<I: I2c> Sh1106<I> {
+    pub fn new(i2c: I, addr: u8) -> Self {
+        Self {
+            i2c,
+            addr,
+            buffer: [0u8; BUF_SIZE],
+        }
+    }
+
+    /// Send a sequence of commands (each prefixed with the I2C command byte 0x00).
+    async fn cmd(&mut self, commands: &[u8]) -> Result<(), I::Error> {
+        for &c in commands {
+            self.i2c.write(self.addr, &[0x00, c]).await?;
+        }
+        Ok(())
+    }
+
+    /// Initialize the display with sensible defaults.
+    pub async fn init(&mut self) -> Result<(), I::Error> {
+        self.cmd(&[
+            0xAE, // display off
+            0xD5, 0x80, // clock div: default
+            0xA8, 0x3F, // multiplex ratio: 64
+            0xD3, 0x00, // display offset: 0
+            0x40, // start line: 0
+            0x8D, 0x14, // charge pump: enable
+            0xA1, // segment remap: column 127 mapped to SEG0
+            0xC8, // COM scan direction: remapped
+            0xDA, 0x12, // COM pin config: alternative, no L/R remap
+            0x81, 0xCF, // contrast: 207
+            0xD9, 0xF1, // pre-charge: phase1=1, phase2=15
+            0xDB, 0x40, // VCOMH deselect: ~0.77×Vcc
+            0xA4, // entire display ON (follow RAM)
+            0xA6, // normal display (not inverted)
+            0xAF, // display on
+        ])
+        .await
+    }
+
+    /// Flush the entire framebuffer to the display, page by page.
+    pub async fn flush(&mut self) -> Result<(), I::Error> {
+        // Each I2C data write is prefixed with 0x40 (data continuation byte).
+        let mut page_buf = [0u8; 1 + WIDTH]; // 0x40 + 128 data bytes
+        page_buf[0] = 0x40;
+
+        for page in 0..PAGES {
+            // Set page address and column start (with SH1106 2-column offset).
+            self.cmd(&[
+                0xB0 | page as u8,          // page address
+                0x00 | (COL_OFFSET & 0x0F), // column low nibble
+                0x10 | (COL_OFFSET >> 4),   // column high nibble
+            ])
+            .await?;
+
+            let start = page * WIDTH;
+            page_buf[1..].copy_from_slice(&self.buffer[start..start + WIDTH]);
+            self.i2c.write(self.addr, &page_buf).await?;
+        }
+        Ok(())
+    }
+
+    /// Set display brightness (contrast).
+    pub async fn set_brightness(&mut self, value: u8) -> Result<(), I::Error> {
+        self.cmd(&[0x81, value]).await
+    }
+
+    /// Clear the framebuffer (call flush() to update the display).
+    pub fn clear_buffer(&mut self) {
+        self.buffer.fill(0);
+    }
+}
+
+impl<I: I2c> DrawTarget for Sh1106<I> {
+    type Color = BinaryColor;
+    type Error = core::convert::Infallible;
+
+    fn draw_iter<T>(&mut self, pixels: T) -> Result<(), Self::Error>
+    where
+        T: IntoIterator<Item = Pixel<Self::Color>>,
+    {
+        for Pixel(pos, color) in pixels {
+            let x = pos.x;
+            let y = pos.y;
+            if x >= 0 && x < WIDTH as i32 && y >= 0 && y < HEIGHT as i32 {
+                let x = x as usize;
+                let y = y as usize;
+                let idx = (y / 8) * WIDTH + x;
+                let bit = (y % 8) as u8;
+                if color.is_on() {
+                    self.buffer[idx] |= 1 << bit;
+                } else {
+                    self.buffer[idx] &= !(1 << bit);
+                }
+            }
+        }
+        Ok(())
+    }
+
+    fn clear(&mut self, color: Self::Color) -> Result<(), Self::Error> {
+        self.buffer.fill(if color.is_on() { 0xFF } else { 0x00 });
+        Ok(())
+    }
+}
+
+impl<I: I2c> OriginDimensions for Sh1106<I> {
+    fn size(&self) -> Size {
+        Size::new(WIDTH as u32, HEIGHT as u32)
+    }
+}
diff --git a/firmware/src/display/task.rs b/firmware/src/display/task.rs
index 2abfc32f..5b28e253 100644
--- a/firmware/src/display/task.rs
+++ b/firmware/src/display/task.rs
@@ -1,15 +1,11 @@
 use embassy_executor::task;
 use embassy_futures::select::{select3, Either3};
 use embassy_time::Timer;
-use ssd1306::mode::DisplayConfigAsync;
-use ssd1306::prelude::DisplayRotation;
-use ssd1306::size::DisplaySize128x64;
-use ssd1306::{I2CDisplayInterface, Ssd1306Async};
+use embedded_graphics::draw_target::DrawTarget;
+use embedded_graphics::pixelcolor::BinaryColor;
 
 use crate::board::DisplayParts;
-use crate::channel::{
-    DisplayCommand, DisplayCommandChannel, RadioState, RadioStatus, StatusWatch,
-};
+use crate::channel::{DisplayCommand, DisplayCommandChannel, RadioState, RadioStatus, StatusWatch};
 
 use crate::board::{Board, LoRaBoard};
 
@@ -80,6 +76,28 @@ impl DisplayState {
     }
 }
 
+/// Render the appropriate screen for the current state into the display buffer.
+fn render_current(
+    display: &mut impl DrawTarget<Color = BinaryColor>,
+    state: &DisplayState,
+    board: &render::BoardInfo<'_>,
+) {
+    if state.is_active() {
+        render::dashboard(
+            display,
+            &state.last_status,
+            &state.rssi_history,
+            &state.tx_history,
+            state.rssi_count,
+            state.current_slot_rssi,
+            state.current_slot_tx,
+            board,
+        );
+    } else {
+        render::splash(display, board);
+    }
+}
+
 #[task]
 pub async fn display_task(
     parts: DisplayParts,
@@ -103,20 +121,51 @@ pub async fn display_task(
         mac: &mac_str,
     };
 
-    let interface = I2CDisplayInterface::new(parts.i2c);
-    let mut display = Ssd1306Async::new(interface, DisplaySize128x64, DisplayRotation::Rotate0)
-        .into_buffered_graphics_mode();
+    cfg_if::cfg_if! {
+        if #[cfg(feature = "wio_tracker_l1")] {
+            let mut display = super::sh1106::Sh1106::new(parts.i2c, 0x3D);
 
-    if display.init().await.is_err() {
-        defmt::error!("SSD1306 init failed");
-        return;
-    }
-    if display
-        .set_brightness(ssd1306::prelude::Brightness::BRIGHTEST)
-        .await
-        .is_err()
-    {
-        defmt::warn!("display brightness set failed");
+            Timer::after_millis(100).await;
+
+            if display.init().await.is_err() {
+                defmt::error!("SH1106 init failed — retrying");
+                Timer::after_millis(500).await;
+                if display.init().await.is_err() {
+                    defmt::error!("SH1106 init failed twice, giving up");
+                    return;
+                }
+            }
+            if display.set_brightness(0xFF).await.is_err() {
+                defmt::warn!("display brightness set failed");
+            }
+        } else {
+            use ssd1306::mode::DisplayConfigAsync;
+            use ssd1306::prelude::DisplayRotation;
+            use ssd1306::size::DisplaySize128x64;
+            use ssd1306::{I2CDisplayInterface, Ssd1306Async};
+
+            let interface = I2CDisplayInterface::new(parts.i2c);
+            let mut display = Ssd1306Async::new(interface, DisplaySize128x64, DisplayRotation::Rotate0)
+                .into_buffered_graphics_mode();
+
+            Timer::after_millis(100).await;
+
+            if display.init().await.is_err() {
+                defmt::error!("SSD1306 init failed — retrying");
+                Timer::after_millis(500).await;
+                if display.init().await.is_err() {
+                    defmt::error!("SSD1306 init failed twice, giving up");
+                    return;
+                }
+            }
+            if display
+                .set_brightness(ssd1306::prelude::Brightness::BRIGHTEST)
+                .await
+                .is_err()
+            {
+                defmt::warn!("display brightness set failed");
+            }
+        }
     }
 
     let mut state = DisplayState::new();
@@ -126,7 +175,8 @@ pub async fn display_task(
     };
 
     // Show splash/waiting screen
-    render_splash(&mut display, &board_info).await;
+    render::splash(&mut display, &board_info);
+    let _ = display.flush().await;
 
     loop {
         match select3(
@@ -151,7 +201,8 @@ pub async fn display_task(
                 state.last_status = radio_status;
 
                 if state.display_on {
-                    render_current(&mut display, &state, &board_info).await;
+                    render_current(&mut display, &state, &board_info);
+                    let _ = display.flush().await;
                 }
             }
             Either3::Second(cmd) => match cmd {
@@ -167,73 +218,23 @@ pub async fn display_task(
                     if let Some(s) = receiver.try_get() {
                         state.last_status = s;
                     }
-                    render_current(&mut display, &state, &board_info).await;
+                    render_current(&mut display, &state, &board_info);
+                    let _ = display.flush().await;
                 }
                 DisplayCommand::Reset => {
                     state = DisplayState::new();
-                    render_splash(&mut display, &board_info).await;
+                    render::splash(&mut display, &board_info);
+                    let _ = display.flush().await;
                 }
             },
             Either3::Third(()) => {
                 // Timer tick: advance sparkline slot
                 state.advance_slot();
                 if state.display_on && state.is_active() {
-                    render_dashboard(&mut display, &state, &board_info).await;
+                    render_current(&mut display, &state, &board_info);
+                    let _ = display.flush().await;
                 }
             }
         }
     }
 }
-
-// The concrete display type is verbose but avoids making this generic
-// over both DrawTarget and the SSD1306-specific flush method.
-type Display<I> = ssd1306::Ssd1306Async<
-    I,
-    DisplaySize128x64,
-    ssd1306::mode::BufferedGraphicsModeAsync<DisplaySize128x64>,
->;
-
-/// Render the appropriate screen (active dashboard or splash) and flush.
-async fn render_current<I>(
-    display: &mut Display<I>,
-    state: &DisplayState,
-    board: &render::BoardInfo<'_>,
-) where
-    I: display_interface::AsyncWriteOnlyDataCommand,
-{
-    if state.is_active() {
-        render_dashboard(display, state, board).await;
-    } else {
-        render_splash(display, board).await;
-    }
-}
-
-/// Render the active dashboard and flush.
-async fn render_dashboard<I>(
-    display: &mut Display<I>,
-    state: &DisplayState,
-    board: &render::BoardInfo<'_>,
-) where
-    I: display_interface::AsyncWriteOnlyDataCommand,
-{
-    render::dashboard(
-        display,
-        &state.last_status,
-        &state.rssi_history,
-        &state.tx_history,
-        state.rssi_count,
-        state.current_slot_rssi,
-        state.current_slot_tx,
-        board,
-    );
-    let _ = display.flush().await;
-}
-
-/// Render the splash/waiting screen and flush.
-async fn render_splash<I>(display: &mut Display<I>, board: &render::BoardInfo<'_>)
-where
-    I: display_interface::AsyncWriteOnlyDataCommand,
-{
-    render::splash(display, board);
-    let _ = display.flush().await;
-}
diff --git a/firmware/src/main.rs b/firmware/src/main.rs
index 86163ee4..25c1c37e 100644
--- a/firmware/src/main.rs
+++ b/firmware/src/main.rs
@@ -37,7 +37,8 @@ use crate::channel::{CommandChannel, DisplayCommandChannel, ResponseChannel, Sta
 
 #[cfg(not(test))]
 cfg_if::cfg_if! {
-    if #[cfg(feature = "rak_wisblock_4631")] {
+    if #[cfg(any(feature = "rak_wisblock_4631", feature = "wio_tracker_l1"))] {
+        use defmt_rtt as _;
         use panic_probe as _;
     } else if #[cfg(any(feature = "heltec_v3", feature = "heltec_v4"))] {
         use esp_backtrace as _;
@@ -56,7 +57,7 @@ static DISPLAY_COMMANDS: DisplayCommandChannel = DisplayCommandChannel::new();
 
 #[cfg(not(test))]
 cfg_if::cfg_if! {
-    if #[cfg(feature = "rak_wisblock_4631")] {
+    if #[cfg(any(feature = "rak_wisblock_4631", feature = "wio_tracker_l1"))] {
         #[embassy_executor::main]
         async fn main(spawner: Spawner) {
             run(spawner).await;
diff --git a/firmware/src/protocol.rs b/firmware/src/protocol.rs
index f62c9eb5..6f05bef4 100644
--- a/firmware/src/protocol.rs
+++ b/firmware/src/protocol.rs
@@ -17,7 +17,6 @@ pub const TX_POWER_MAX: i8 = i8::MIN; // -128 on the wire
 /// Sentinel value for `preamble_len`: use the firmware default (16 symbols).
 pub const PREAMBLE_DEFAULT: u16 = 0;
 
-
 /// LoRa signal bandwidth.
 #[derive(Debug, Clone, Copy, PartialEq, Eq)]
 #[cfg_attr(not(test), derive(defmt::Format))]
@@ -188,7 +187,10 @@ impl Command {
                 let (config, pos) = if rest[0] == 0 {
                     (None, 1)
                 } else if rest[0] == 1 && rest.len() > RADIO_CONFIG_SIZE {
-                    (Some(RadioConfig::from_bytes(&rest[1..])?), 1 + RADIO_CONFIG_SIZE)
+                    (
+                        Some(RadioConfig::from_bytes(&rest[1..])?),
+                        1 + RADIO_CONFIG_SIZE,
+                    )
                 } else {
                     return None;
                 };
@@ -370,7 +372,10 @@ mod tests {
         let power_range = (-9, 22);
         let base = make_config();
 
-        let mut cfg = RadioConfig { freq_hz: 150_000_000, ..base };
+        let mut cfg = RadioConfig {
+            freq_hz: 150_000_000,
+            ..base
+        };
         assert!(cfg.validate(power_range).is_ok());
 
         cfg.freq_hz = 960_000_000;
@@ -392,7 +397,9 @@ mod tests {
             assert!(RadioConfig { sf, ..base }.validate(power_range).is_ok());
         }
         assert!(RadioConfig { sf: 4, ..base }.validate(power_range).is_err());
-        assert!(RadioConfig { sf: 13, ..base }.validate(power_range).is_err());
+        assert!(RadioConfig { sf: 13, ..base }
+            .validate(power_range)
+            .is_err());
     }
 
     #[test]
@@ -409,22 +416,34 @@ mod tests {
 
     #[test]
     fn validate_tx_power_max_sentinel() {
-        let cfg = RadioConfig { tx_power_dbm: TX_POWER_MAX, ..make_config() };
+        let cfg = RadioConfig {
+            tx_power_dbm: TX_POWER_MAX,
+            ..make_config()
+        };
         assert!(cfg.validate((-9, 22)).is_ok());
     }
 
     #[test]
     fn validate_tx_power_out_of_range() {
-        let cfg = RadioConfig { tx_power_dbm: 23, ..make_config() };
+        let cfg = RadioConfig {
+            tx_power_dbm: 23,
+            ..make_config()
+        };
         assert!(cfg.validate((-9, 22)).is_err());
 
-        let cfg = RadioConfig { tx_power_dbm: -10, ..make_config() };
+        let cfg = RadioConfig {
+            tx_power_dbm: -10,
+            ..make_config()
+        };
         assert!(cfg.validate((-9, 22)).is_err());
     }
 
     #[test]
     fn validate_preamble_default_sentinel() {
-        let cfg = RadioConfig { preamble_len: PREAMBLE_DEFAULT, ..make_config() };
+        let cfg = RadioConfig {
+            preamble_len: PREAMBLE_DEFAULT,
+            ..make_config()
+        };
         assert!(cfg.validate((-9, 22)).is_ok());
     }
 
@@ -433,33 +452,55 @@ mod tests {
         let power_range = (-9, 22);
         let base = make_config();
 
-        assert!(RadioConfig { preamble_len: 6, ..base }.validate(power_range).is_ok());
-        assert!(RadioConfig { preamble_len: 5, ..base }.validate(power_range).is_err());
+        assert!(RadioConfig {
+            preamble_len: 6,
+            ..base
+        }
+        .validate(power_range)
+        .is_ok());
+        assert!(RadioConfig {
+            preamble_len: 5,
+            ..base
+        }
+        .validate(power_range)
+        .is_err());
     }
 
     // ── RadioConfig::resolve ──────────────────────────────────────
 
     #[test]
     fn resolve_power_max_sentinel() {
-        let cfg = RadioConfig { tx_power_dbm: TX_POWER_MAX, ..make_config() };
+        let cfg = RadioConfig {
+            tx_power_dbm: TX_POWER_MAX,
+            ..make_config()
+        };
         assert_eq!(cfg.resolve((-9, 22)).tx_power_dbm, 22);
     }
 
     #[test]
     fn resolve_power_explicit_unchanged() {
-        let cfg = RadioConfig { tx_power_dbm: 10, ..make_config() };
+        let cfg = RadioConfig {
+            tx_power_dbm: 10,
+            ..make_config()
+        };
         assert_eq!(cfg.resolve((-9, 22)).tx_power_dbm, 10);
     }
 
     #[test]
     fn resolve_preamble_default() {
-        let cfg = RadioConfig { preamble_len: PREAMBLE_DEFAULT, ..make_config() };
+        let cfg = RadioConfig {
+            preamble_len: PREAMBLE_DEFAULT,
+            ..make_config()
+        };
         assert_eq!(cfg.resolve((-9, 22)).preamble_len, 16);
     }
 
     #[test]
     fn resolve_preamble_explicit_unchanged() {
-        let cfg = RadioConfig { preamble_len: 32, ..make_config() };
+        let cfg = RadioConfig {
+            preamble_len: 32,
+            ..make_config()
+        };
         assert_eq!(cfg.resolve((-9, 22)).preamble_len, 32);
     }
 
@@ -608,7 +649,12 @@ mod tests {
         let mut payload = Vec::new();
         let _ = payload.extend_from_slice(b"data");
         let mut buf = [0u8; 64];
-        let n = Response::RxPacket { rssi: -80, snr: 10, payload }.write_to(&mut buf);
+        let n = Response::RxPacket {
+            rssi: -80,
+            snr: 10,
+            payload,
+        }
+        .write_to(&mut buf);
         assert_eq!(n, 7 + 4); // tag(1) + rssi(2) + snr(2) + len(2) + "data"(4)
         assert_eq!(buf[0], 2);
         assert_eq!(i16::from_le_bytes([buf[1], buf[2]]), -80);
diff --git a/firmware/src/radio/task.rs b/firmware/src/radio/task.rs
index ed2b8f9d..99d09e3b 100644
--- a/firmware/src/radio/task.rs
+++ b/firmware/src/radio/task.rs
@@ -125,9 +125,7 @@ pub async fn radio_task(
                             warn!("restart RX failed: {}", e);
                             state.state = RadioState::Idle;
                             status.sender().send(state.clone());
-                            responses
-                                .send(Response::Error(ErrorCode::RadioBusy))
-                                .await;
+                            responses.send(Response::Error(ErrorCode::RadioBusy)).await;
                         }
                     }
                     Err(e) => {
@@ -135,9 +133,7 @@ pub async fn radio_task(
                         if start_rx(&mut lora, &cfg).await.is_err() {
                             state.state = RadioState::Idle;
                             status.sender().send(state.clone());
-                            responses
-                                .send(Response::Error(ErrorCode::RadioBusy))
-                                .await;
+                            responses.send(Response::Error(ErrorCode::RadioBusy)).await;
                         }
                     }
                 },
@@ -218,7 +214,9 @@ async fn handle_cmd(
         }
         Command::DisplayOn | Command::DisplayOff | Command::GetMac => {}
         Command::Transmit { config, payload } => {
-            let tx_config = config.map(|c| c.resolve(Board::TX_POWER_RANGE)).or(state.config);
+            let tx_config = config
+                .map(|c| c.resolve(Board::TX_POWER_RANGE))
+                .or(state.config);
             if let Some(cfg) = tx_config {
                 if let Err(reason) = cfg.validate(Board::TX_POWER_RANGE) {
                     warn!("TX config rejected: {}", reason);
@@ -239,9 +237,7 @@ async fn handle_cmd(
                     }
                     Err(e) => {
                         warn!("TX failed: {}", e);
-                        responses
-                            .send(Response::Error(ErrorCode::TxTimeout))
-                            .await;
+                        responses.send(Response::Error(ErrorCode::TxTimeout)).await;
                     }
                 }
 
@@ -331,7 +327,12 @@ fn modulation_params(
 async fn start_rx(lora: &mut Radio, cfg: &RadioConfig) -> Result<(), RadioError> {
     let mdltn = modulation_params(lora, cfg)?;
     let pkt = lora.create_rx_packet_params(
-        cfg.preamble_len, IMPLICIT_HEADER, MAX_PAYLOAD as u8, CRC_ON, IQ_INVERTED, &mdltn,
+        cfg.preamble_len,
+        IMPLICIT_HEADER,
+        MAX_PAYLOAD as u8,
+        CRC_ON,
+        IQ_INVERTED,
+        &mdltn,
     )?;
     lora.prepare_for_rx(RxMode::Continuous, &mdltn, &pkt).await
 }
@@ -343,7 +344,12 @@ async fn rx_once(
 ) -> Result<(u8, lora_phy::mod_params::PacketStatus), RadioError> {
     let mdltn = modulation_params(lora, cfg)?;
     let pkt = lora.create_rx_packet_params(
-        cfg.preamble_len, IMPLICIT_HEADER, MAX_PAYLOAD as u8, CRC_ON, IQ_INVERTED, &mdltn,
+        cfg.preamble_len,
+        IMPLICIT_HEADER,
+        MAX_PAYLOAD as u8,
+        CRC_ON,
+        IQ_INVERTED,
+        &mdltn,
     )?;
     lora.rx(&pkt, buf).await
 }
@@ -368,7 +374,11 @@ async fn do_tx(lora: &mut Radio, cfg: &RadioConfig, payload: &[u8]) -> Result<()
     }
 
     let mut tx_pkt = lora.create_tx_packet_params(
-        cfg.preamble_len, IMPLICIT_HEADER, CRC_ON, IQ_INVERTED, &mdltn,
+        cfg.preamble_len,
+        IMPLICIT_HEADER,
+        CRC_ON,
+        IQ_INVERTED,
+        &mdltn,
     )?;
     lora.prepare_for_tx(&mdltn, &mut tx_pkt, cfg.tx_power_dbm as i32, payload)
         .await?;
diff --git a/firmware/src/usb/task.rs b/firmware/src/usb/task.rs
index e005581a..246be4f5 100644
--- a/firmware/src/usb/task.rs
+++ b/firmware/src/usb/task.rs
@@ -10,9 +10,7 @@ use embassy_usb::class::cdc_acm::{CdcAcmClass, Receiver, Sender, State};
 use embassy_usb::Builder;
 use static_cell::StaticCell;
 
-use crate::channel::{
-    CommandChannel, DisplayCommand, DisplayCommandChannel, ResponseChannel,
-};
+use crate::channel::{CommandChannel, DisplayCommand, DisplayCommandChannel, ResponseChannel};
 use crate::protocol::{Command, ErrorCode, Response};
 
 const MAX_FRAME: usize = 512;
@@ -68,14 +66,7 @@ pub async fn usb_task(
     let ctrl_buf = CTRL_BUF.init([0; 64]);
     let cdc_state = CDC_STATE.init(State::new());
 
-    let mut builder = Builder::new(
-        parts.driver,
-        config,
-        desc_buf,
-        conf_buf,
-        bos_buf,
-        ctrl_buf,
-    );
+    let mut builder = Builder::new(parts.driver, config, desc_buf, conf_buf, bos_buf, ctrl_buf);
 
     let class = CdcAcmClass::new(&mut builder, cdc_state, MAX_PACKET as u16);
     let mut usb_dev = builder.build();
@@ -84,7 +75,15 @@ pub async fn usb_task(
     // ── Run USB device + protocol loop concurrently ────────────────
     join(
         usb_dev.run(),
-        protocol_loop(sender, receiver, commands, responses, display_commands, has_display, mac),
+        protocol_loop(
+            sender,
+            receiver,
+            commands,
+            responses,
+            display_commands,
+            has_display,
+            mac,
+        ),
     )
     .await;
 }
@@ -141,7 +140,12 @@ async fn protocol_loop<'d, D: embassy_usb_driver::Driver<'d>>(
                             {
                                 if let Some(cmd) = Command::from_bytes(&decode_buf[..decoded_len]) {
                                     route_command(
-                                        cmd, commands, responses, display_commands, has_display, mac,
+                                        cmd,
+                                        commands,
+                                        responses,
+                                        display_commands,
+                                        has_display,
+                                        mac,
                                     )
                                     .await;
                                 }
@@ -160,8 +164,8 @@ async fn protocol_loop<'d, D: embassy_usb_driver::Driver<'d>>(
             Either3::Second(response) => {
                 // Serialize response to fixed-size LE bytes, then COBS encode
                 let raw_len = response.write_to(&mut write_buf);
-                let encoded_len = ucobs::encode(&write_buf[..raw_len], &mut cobs_encode_buf)
-                    .unwrap_or(0);
+                let encoded_len =
+                    ucobs::encode(&write_buf[..raw_len], &mut cobs_encode_buf).unwrap_or(0);
                 // Append 0x00 sentinel
                 if encoded_len < cobs_encode_buf.len() {
                     cobs_encode_buf[encoded_len] = 0x00;
diff --git a/mux/rust/src/main.rs b/mux/rust/src/main.rs
index 5f7562f0..dfcf0e59 100644
--- a/mux/rust/src/main.rs
+++ b/mux/rust/src/main.rs
@@ -50,16 +50,14 @@ async fn main() -> anyhow::Result<()> {
     // Resolve serial port
     let port = match args.port {
         Some(p) => p,
-        None => {
-            tokio::task::spawn_blocking(|| {
-                donglora_client::find_port().unwrap_or_else(|| {
-                    info!("waiting for DongLoRa device...");
-                    donglora_client::wait_for_device()
-                })
+        None => tokio::task::spawn_blocking(|| {
+            donglora_client::find_port().unwrap_or_else(|| {
+                info!("waiting for DongLoRa device...");
+                donglora_client::wait_for_device()
             })
-            .await
-            .map_err(|e| anyhow::anyhow!("device discovery task failed: {e}"))?
-        }
+        })
+        .await
+        .map_err(|e| anyhow::anyhow!("device discovery task failed: {e}"))?,
     };
 
     // Resolve socket path
@@ -102,12 +100,10 @@ fn parse_tcp_addr(tcp: &str) -> Option<(String, u16)> {
 }
 
 async fn signal_handler(shutdown: CancellationToken) -> anyhow::Result<()> {
-    let mut sigint =
-        tokio::signal::unix::signal(tokio::signal::unix::SignalKind::interrupt())
-            .map_err(|e| anyhow::anyhow!("failed to register SIGINT handler: {e}"))?;
-    let mut sigterm =
-        tokio::signal::unix::signal(tokio::signal::unix::SignalKind::terminate())
-            .map_err(|e| anyhow::anyhow!("failed to register SIGTERM handler: {e}"))?;
+    let mut sigint = tokio::signal::unix::signal(tokio::signal::unix::SignalKind::interrupt())
+        .map_err(|e| anyhow::anyhow!("failed to register SIGINT handler: {e}"))?;
+    let mut sigterm = tokio::signal::unix::signal(tokio::signal::unix::SignalKind::terminate())
+        .map_err(|e| anyhow::anyhow!("failed to register SIGTERM handler: {e}"))?;
 
     tokio::select! {
         _ = sigint.recv() => info!("received SIGINT"),