swaitsandClaude Opus 4.6
3102fc747a
Implement full SSD1306 OLED display support: - Splash screen on boot (1.5s) with project name, version, board - Dashboard showing radio state, config, counters, RSSI/SNR - RSSI history sparkline (64-sample ring buffer, 2px-wide bars) - DisplayOn/DisplayOff host commands routed via dedicated channel - Pure render functions against generic DrawTarget (no hardware coupling) - Display on/off control bypasses radio task entirely Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
87 lines
2.3 KiB
Rust
87 lines
2.3 KiB
Rust
//! This example draws a small square one pixel at a time in the top left corner of the display
|
|
//!
|
|
//! You will probably want to use the [`embedded_graphics`](https://crates.io/crates/embedded-graphics) crate to do more complex drawing.
|
|
//!
|
|
//! This example is for the STM32F103 "Blue Pill" board using a 4 wire interface to the display on
|
|
//! SPI1.
|
|
//!
|
|
//! Wiring connections are as follows
|
|
//!
|
|
//! ```
|
|
//! GND -> GND
|
|
//! 3V3 -> VCC
|
|
//! PA5 -> SCL (D0)
|
|
//! PA7 -> SDA (D1)
|
|
//! PB0 -> RST
|
|
//! PB1 -> D/C
|
|
//! PB10 -> CS
|
|
//! ```
|
|
//!
|
|
//! Run on a Blue Pill with `cargo run --example pixelsquare`.
|
|
|
|
#![no_std]
|
|
#![no_main]
|
|
|
|
use cortex_m::asm::nop;
|
|
use cortex_m_rt::entry;
|
|
use defmt_rtt as _;
|
|
use embassy_stm32::{
|
|
gpio,
|
|
spi::{self, Spi},
|
|
time::Hertz,
|
|
};
|
|
use panic_probe as _;
|
|
use ssd1306::{prelude::*, Ssd1306};
|
|
|
|
#[entry]
|
|
fn main() -> ! {
|
|
let p = embassy_stm32::init(Default::default());
|
|
let mut config = spi::Config::default();
|
|
config.frequency = Hertz::mhz(8);
|
|
let spi = Spi::new_blocking_txonly(p.SPI1, p.PA5, p.PA7, config);
|
|
|
|
let mut rst = gpio::Output::new(p.PB0, gpio::Level::Low, gpio::Speed::Low);
|
|
let dc = gpio::Output::new(p.PB1, gpio::Level::Low, gpio::Speed::Low);
|
|
let cs = gpio::Output::new(p.PB10, gpio::Level::Low, gpio::Speed::Low);
|
|
let spi = embedded_hal_bus::spi::ExclusiveDevice::new_no_delay(spi, cs).unwrap();
|
|
|
|
let interface = display_interface_spi::SPIInterface::new(spi, dc);
|
|
let mut display = Ssd1306::new(interface, DisplaySize128x64, DisplayRotation::Rotate0)
|
|
.into_buffered_graphics_mode();
|
|
|
|
display
|
|
.reset(&mut rst, &mut embassy_time::Delay {})
|
|
.unwrap();
|
|
display.init().unwrap();
|
|
|
|
// Top side
|
|
display.set_pixel(0, 0, true);
|
|
display.set_pixel(1, 0, true);
|
|
display.set_pixel(2, 0, true);
|
|
display.set_pixel(3, 0, true);
|
|
|
|
// Right side
|
|
display.set_pixel(3, 0, true);
|
|
display.set_pixel(3, 1, true);
|
|
display.set_pixel(3, 2, true);
|
|
display.set_pixel(3, 3, true);
|
|
|
|
// Bottom side
|
|
display.set_pixel(0, 3, true);
|
|
display.set_pixel(1, 3, true);
|
|
display.set_pixel(2, 3, true);
|
|
display.set_pixel(3, 3, true);
|
|
|
|
// Left side
|
|
display.set_pixel(0, 0, true);
|
|
display.set_pixel(0, 1, true);
|
|
display.set_pixel(0, 2, true);
|
|
display.set_pixel(0, 3, true);
|
|
|
|
display.flush().unwrap();
|
|
|
|
loop {
|
|
nop()
|
|
}
|
|
}
|