swaits
e60465f181
Per the Wio Tracker L1 schematic, it has a green LED on P1.01. Moved SimpleLed from driver/ to board layer (esp32s3.rs and wio_tracker_l1.rs) since the impl needs HAL-specific Output types. Removed driver/simple_led.rs — each board layer defines its own. RAK WisBlock remains LedDriver=() (no user LED on the core module).
94 lines
2.8 KiB
Rust
94 lines
2.8 KiB
Rust
//! Heltec WiFi LoRa 32 V3 — stock UART (via CP2102 bridge).
|
|
//!
|
|
//! This is for unmodified V3 boards where USB goes through the CP2102
|
|
//! bridge to UART0. The board appears as /dev/ttyUSB* (not ttyACM*).
|
|
//!
|
|
//! If you've done the hardware mod (solder R29/R3, disconnect CP2102),
|
|
//! use the `heltec_v3` feature instead for native USB CDC-ACM support.
|
|
|
|
use esp_hal::gpio::{Level, Output, OutputConfig};
|
|
|
|
use super::esp32s3;
|
|
use super::traits::{BoardParts, LoRaBoard};
|
|
use super::esp32s3::SimpleLed;
|
|
use crate::hal::esp32s3 as mcu;
|
|
|
|
pub use super::esp32s3::{
|
|
create_display, DisplayDriver, DisplayParts, RadioDriver, RadioParts,
|
|
};
|
|
|
|
pub type UartDriver = esp_hal::uart::Uart<'static, esp_hal::Async>;
|
|
pub type LedDriver = SimpleLed;
|
|
|
|
pub struct UartParts {
|
|
pub driver: UartDriver,
|
|
}
|
|
|
|
pub struct Board {
|
|
p: esp_hal::peripherals::Peripherals,
|
|
}
|
|
|
|
impl LoRaBoard for Board {
|
|
const NAME: &'static str = "Heltec V3 (UART)";
|
|
const TX_POWER_RANGE: (i8, i8) = (-9, 22);
|
|
|
|
type RadioParts = RadioParts;
|
|
type CommParts = UartParts;
|
|
type DisplayParts = DisplayParts;
|
|
type DisplayDriver = DisplayDriver;
|
|
type LedDriver = LedDriver;
|
|
|
|
fn init() -> Self {
|
|
let p = esp_hal::init(esp_hal::Config::default());
|
|
Self { p }
|
|
}
|
|
|
|
fn mac_address() -> [u8; 6] {
|
|
mcu::mac_address()
|
|
}
|
|
|
|
fn into_parts(self) -> BoardParts<RadioParts, UartParts, DisplayParts, LedDriver> {
|
|
let p = self.p;
|
|
|
|
mcu::start_timer(p.TIMG0);
|
|
|
|
// Vext power: GPIO36, active LOW to enable peripherals
|
|
let vext = Output::new(p.GPIO36, Level::Low, OutputConfig::default());
|
|
core::mem::forget(vext);
|
|
|
|
let spi_bus = mcu::init_spi(p.SPI2, p.DMA_CH0, p.GPIO9, p.GPIO10, p.GPIO11);
|
|
let radio = esp32s3::init_radio(spi_bus, p.GPIO8, p.GPIO12, p.GPIO14, p.GPIO13);
|
|
|
|
use esp_hal::uart::{Config as UartConfig, Uart};
|
|
let host = UartParts {
|
|
driver: Uart::new(p.UART0, UartConfig::default())
|
|
.expect("UART init")
|
|
.with_tx(p.GPIO43)
|
|
.with_rx(p.GPIO44)
|
|
.into_async(),
|
|
};
|
|
|
|
// SSD1306 display reset: pulse GPIO21 low->high before I2C init
|
|
let mut display_rst = Output::new(p.GPIO21, Level::Low, OutputConfig::default());
|
|
esp_hal::delay::Delay::new().delay_millis(10);
|
|
display_rst.set_high();
|
|
esp_hal::delay::Delay::new().delay_millis(10);
|
|
core::mem::forget(display_rst);
|
|
|
|
let i2c = mcu::init_i2c(p.I2C0, p.GPIO17, p.GPIO18);
|
|
let display = Some(DisplayParts { i2c });
|
|
|
|
// White LED on GPIO35
|
|
let led_pin = Output::new(p.GPIO35, Level::Low, OutputConfig::default());
|
|
let led = Some(SimpleLed(led_pin));
|
|
|
|
BoardParts {
|
|
radio,
|
|
host,
|
|
display,
|
|
led,
|
|
mac: Self::mac_address(),
|
|
}
|
|
}
|
|
}
|