Replaces the ad-hoc display loop with a declarative hsmc statechart
(Off/On.{Splash.{LearnMore,Info}, Dashboard.{Listening,Transmitting}})
and swaps the Radio→Display channel from a RadioStatus watch to a
typed RadioEvent queue. The radio task now emits discrete mode and
packet events instead of publishing full status snapshots; the
display consumes them through the statechart, which also handles the
5 s splash alternation and 1 s sparkline tick via `on(after …)` /
`on(every …)` transitions.
Also:
- Add hsmc dep and embassy/tokio feature shims (hsmc proc macro
evaluates `cfg(feature = "embassy")` in this crate).
- Fix USB disconnect path in `host/usb.rs` so the DTR branch always
runs on read error (was early-continuing, starving display/radio
reset).
Pulls the wire protocol types and COBS framing out of firmware and into
the sibling ../protocol crate so client-rs, mux-rs, and bridge can share
them. Firmware's src/protocol.rs is now a thin re-export shim preserving
every crate::protocol::\* call site; src/host/framing.rs drops the
in-tree CobsDecoder / cobs_encode_response and re-exports the codec,
keeping only route_command (which needs embassy channels).
All seven board features still build clean, cargo fmt clean, cargo test
green.
Bump embassy-executor 0.9 -> 0.10 and embassy-rp 0.9 -> 0.10 from crates.io.
Patch esp-hal, esp-rtos, esp-backtrace, esp-println from esp-rs/esp-hal main
branch (esp-rtos 0.2.0 on crates.io pins embassy-executor ^0.9).
API migrations:
- embassy-executor: arch-cortex-m -> platform-cortex-m feature rename
- embassy-executor: SpawnToken now returned as Result from task functions
- esp-hal main: efuse::Efuse::mac_address() -> efuse::base_mac_address()
- esp-hal main: esp_rtos::start() now requires SoftwareInterrupt<0>
- embassy-rp 0.10: SPI constructor requires DMA interrupt bindings
Also fixes UART display stuck on splash (sent Reset instead of On at boot)
and switches just check to clippy -D warnings.
First RP2040 board and third MCU family (after ESP32-S3 and nRF52840).
Hardware: RP2040 + SX1262 radio, 850-930 MHz HF, PE4259 antenna switch,
LED on GPIO25, no OLED, USB-C via FPC ribbon cable to adapter board.
New files:
- src/hal/rp2040.rs: MCU primitives (SPI bus, USB driver, flash unique ID MAC)
- src/board/waveshare_rp2040_lora.rs: board implementation
- ld/rp2040-memory.x: linker memory layout
Also fixes cortex-m-rt/set-vtor (moved from global dep to per-board feature,
since Cortex-M0+ has no VTOR register) and makes build.rs memory.x selection
target-aware.
- Set disconnected flag on DisplayCommand::Reset to block stale radio
status updates from re-rendering dashboard over splash screen
- Send StopRx to radio when USB DTR drops so radio stops generating
packets after host disconnects
- Use try_send for unsolicited responses (RxPacket, error recovery,
StopRx Ok) to prevent radio task deadlock on full response channel
- Fall back to LED-only event loop when display init fails instead of
returning early and orphaning the LED
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
Major architecture reorganization, Wio Tracker L1 support, LED blink
on packet activity, native USB for Heltec V3 (hardware mod required).
See CHANGELOG.md for full details.
- Added embedded-hal 1.0 as direct dep (already transitive via embedded-hal-async)
- SimpleLed<P: OutputPin> now generic over any HAL — single definition in driver/
- Removed duplicate SimpleLed from board/esp32s3.rs and board/wio_tracker_l1.rs
- Changed BoardParts.led from Option<L> to L — boards with no LED use ()
- Display task calls led.set_rgb() unconditionally (no-op for () boards)
- RAK board: led: () instead of led: None
swaits
