swaits
4d723a85ce
SX1262's BUSY pin has an internal 20 kΩ pull-up (datasheet page 53). Our Input::new(..., Pull::Down) on BUSY creates contention with that internal pull-up, leaving BUSY at an indeterminate voltage. This can cause wait_on_busy to mis-read the chip's ready state — sometimes commands land while the chip is still busy (ignored or corrupted), which manifests as TX_DONE never firing on DIO1 because the SX1262 never actually completed the SetTx it received during BUSY=high. Fix per lora-rs/lora-rs#260: Pull::Down → Pull::None on BUSY. Matches the official lora-rs nRF52840 examples. Applied to both Wio Tracker L1 (reported broken by @swaits today) and RAK4631 (currently works for us, but was affected by the same class of bug per the upstream issue — this makes it deterministically correct rather than 'happens to work').
DongLoRa Firmware
Embedded Rust firmware for DongLoRa boards. Exposes the LoRa radio over USB CDC-ACM using a COBS-framed binary protocol.
Building
just setup # one-time toolchain install
just build heltec_v4 # build for a specific board
just flash heltec_v4 # build + flash
just check-all # compile-check all boards
just clippy heltec_v4 # lint
just test # host-side protocol unit tests
All commands are run from the firmware/ directory.
Supported Boards
| Board | Feature | MCU | Radio | USB | Target |
|---|---|---|---|---|---|
| Heltec V3 | heltec_v3 |
ESP32-S3 | SX1262 | Native CDC-ACM | xtensa-esp32s3-none-elf |
| Heltec V3 (UART) | heltec_v3_uart |
ESP32-S3 | SX1262 | CP2102 bridge | xtensa-esp32s3-none-elf |
| Heltec V4 | heltec_v4 |
ESP32-S3 | SX1262 | Native CDC-ACM | xtensa-esp32s3-none-elf |
| ELECROW ThinkNode-M2 | elecrow_thinknode_m2 |
ESP32-S3 | SX1262 | CP2102 bridge | xtensa-esp32s3-none-elf |
| LilyGo T-Beam | lilygo_tbeam |
ESP32 | SX1276 | CP2102 bridge | xtensa-esp32-none-elf |
| LilyGo T-Beam S3 Supreme | lilygo_tbeam_supreme |
ESP32-S3 | SX1262 | Native CDC-ACM | xtensa-esp32s3-none-elf |
| RAK WisBlock 4631 | rak_wisblock_4631 |
nRF52840 | SX1262 | Native CDC-ACM | thumbv7em-none-eabihf |
| Waveshare RP2040-LoRa | waveshare_rp2040_lora |
RP2040 | SX1262 | Native CDC-ACM | thumbv6m-none-eabi |
| Wio Tracker L1 | wio_tracker_l1 |
nRF52840 | SX1262 | Native CDC-ACM | thumbv7em-none-eabihf |
Heltec V3 USB Note
The default heltec_v3 build uses native USB CDC-ACM, which requires a
hardware modification to your board. Stock Heltec V3 boards route USB through a
CP2102 bridge chip to UART — the ESP32-S3's native USB pins (GPIO19/GPIO20) are
routed to header pins but not connected to the USB connector.
To enable native USB on a Heltec V3:
- Solder 0-ohm (or 22-ohm) resistors at pads R29 (D+) and R3 (D-)
- Disconnect the CP2102 from the USB connector's D+/D- lines (cut traces or remove the CP2102 bridge resistors)
After this mod, the board appears as /dev/ttyACM0 with the DongLoRa VID:PID
(1209:5741), just like the V4 and nRF boards.
If you have a stock (unmodified) V3, use heltec_v3_uart instead:
just build heltec_v3_uart
just flash heltec_v3_uart
This builds firmware that communicates via the CP2102 bridge (appears as
/dev/ttyUSB0).
Adding a Board
See src/board/PORTING.md.
Protocol
See PROTOCOL.md for the complete wire format specification.