swaits
7184610eea
Bump embassy-executor 0.9 -> 0.10 and embassy-rp 0.9 -> 0.10 from crates.io. Patch esp-hal, esp-rtos, esp-backtrace, esp-println from esp-rs/esp-hal main branch (esp-rtos 0.2.0 on crates.io pins embassy-executor ^0.9). API migrations: - embassy-executor: arch-cortex-m -> platform-cortex-m feature rename - embassy-executor: SpawnToken now returned as Result from task functions - esp-hal main: efuse::Efuse::mac_address() -> efuse::base_mac_address() - esp-hal main: esp_rtos::start() now requires SoftwareInterrupt<0> - embassy-rp 0.10: SPI constructor requires DMA interrupt bindings Also fixes UART display stuck on splash (sent Reset instead of On at boot) and switches just check to clippy -D warnings.
DongLoRa Firmware
Embedded Rust firmware for DongLoRa boards. Exposes the LoRa radio over USB CDC-ACM using a COBS-framed binary protocol.
Building
just setup # one-time toolchain install
just build heltec_v4 # build for a specific board
just flash heltec_v4 # build + flash
just check-all # compile-check all boards
just clippy heltec_v4 # lint
just test # host-side protocol unit tests
All commands are run from the firmware/ directory.
Supported Boards
| Board | Feature | MCU | Radio | USB | Target |
|---|---|---|---|---|---|
| Heltec V3 | heltec_v3 |
ESP32-S3 | SX1262 | Native CDC-ACM | xtensa-esp32s3-none-elf |
| Heltec V3 (UART) | heltec_v3_uart |
ESP32-S3 | SX1262 | CP2102 bridge | xtensa-esp32s3-none-elf |
| Heltec V4 | heltec_v4 |
ESP32-S3 | SX1262 | Native CDC-ACM | xtensa-esp32s3-none-elf |
| RAK WisBlock 4631 | rak_wisblock_4631 |
nRF52840 | SX1262 | Native CDC-ACM | thumbv7em-none-eabihf |
| Waveshare RP2040-LoRa | waveshare_rp2040_lora |
RP2040 | SX1262 | Native CDC-ACM | thumbv6m-none-eabi |
| Wio Tracker L1 | wio_tracker_l1 |
nRF52840 | SX1262 | Native CDC-ACM | thumbv7em-none-eabihf |
Heltec V3 USB Note
The default heltec_v3 build uses native USB CDC-ACM, which requires a
hardware modification to your board. Stock Heltec V3 boards route USB through a
CP2102 bridge chip to UART — the ESP32-S3's native USB pins (GPIO19/GPIO20) are
routed to header pins but not connected to the USB connector.
To enable native USB on a Heltec V3:
- Solder 0-ohm (or 22-ohm) resistors at pads R29 (D+) and R3 (D-)
- Disconnect the CP2102 from the USB connector's D+/D- lines (cut traces or remove the CP2102 bridge resistors)
After this mod, the board appears as /dev/ttyACM0 with the DongLoRa VID:PID
(1209:5741), just like the V4 and nRF boards.
If you have a stock (unmodified) V3, use heltec_v3_uart instead:
just build heltec_v3_uart
just flash heltec_v3_uart
This builds firmware that communicates via the CP2102 bridge (appears as
/dev/ttyUSB0).
Adding a Board
See src/board/PORTING.md.
Protocol
See PROTOCOL.md for the complete wire format specification.