firmware/CHANGELOG.md

Changelog

All notable changes to this project will be documented in this file.

The format is based on Keep a Changelog, and this project adheres to Semantic Versioning.

[Unreleased]

Added

• LilyGo T-Beam S3 Supreme board support (ESP32-S3 + SX1262 + SH1106 OLED + AXP2101 PMIC, native USB-C).
  • Pin map verified against MeshCore's variants/lilygo_tbeam_supreme_SX1262.
  • New src/driver/axp.rs module with an AXP2101 init sequence (ALDO3 = 3.3 V LoRa, ALDO1 = 3.3 V OLED). The PMIC gates LoRa and display power — without it the SX1262 never responds on SPI.
  • PMIC lives on a dedicated I²C1 bus (SDA=42, SCL=41), separate from the SH1106 on I²C0 (SDA=17, SCL=18). I²C1 is used blocking for a one-shot init and then dropped.
  • TCXO driven at 1.6 V via DIO3 (MeshCore uses the same).

[1.2.1] - 2026-04-23

Fixed

• Radio no longer drops to Idle mid-RX-session on transient failures. Extends the v1.1.0 invariant ("SET_CONFIG during RX auto-re-arms") to all failure paths that can occur while a client has RX active:

  • Receiving.on(RxFailed) => Idle now transitions to ResumingRx instead of Idle. A transient next_packet error re-arms the chip rather than ending the RX session.
  • TransmittingFromRx.on(TransmitFailed) => Idle now transitions to ResumingRx. TX failure during an active RX session returns TX_FAILED to the caller and resumes RX, matching the shape of the adjacent ChannelBusy handler.
  • ResumingRx.on(StartRxFailed) => Idle is now a bounded retry (5 × 25 ms backoff via a new bump_resume_retries action and a ResumeRxRetry / ResumeRxExhausted pair of internal events). The chip only lands in Idle after exhausting the retry budget — which means it's genuinely wedged and needs reconfiguring.

  Visible effect: the OLED dashboard no longer bounces to Splash when ai-bot (or any other client that TXes while RX is running) sends a packet. Previously any of the three transitions above would fire RadioEvent::Idle, which the display uses as its Dashboard → Splash trigger; the radio would land in Idle with no client aware enough to re-send RX_START, stranding the dashboard until the session was manually torn down and restarted.

• Removed announce_rx_failed helper action: its only purpose was emitting RadioEvent::Idle on the now-deleted Receiving.on(RxFailed) => Idle edge. No replacement needed — ResumingRx handles recovery silently.

[1.2.0] - 2026-04-22

Added

• OLED auto-dim after inactivity. The display is bright on any activity — splash entry, mode change into a dashboard leaf, packet RX/TX — and dims after a short idle window. Splash holds bright for 10 s, then drops to dim while the LearnMore / Info carousel keeps alternating. The dashboard stays bright for 3 s after the last packet or mode change, then dims in place without changing Listening/Transmitting state. Cross-leaf TX↔RX hops transition bright→bright with no intermediate dim — set_dim is fired as an action by the 3 s timer handler rather than as a sibling exit: action, so mode-change leaf-crossings never see a flash.
• DisplayBrightness trait in src/driver/mod.rs unifies the two-level backlight API across the ssd1306 crate's Ssd1306Async and the in-tree Sh1106 driver. Contrast values centralized as CONTRAST_BRIGHT (0xFF) and CONTRAST_DIM (0x08) constants so the two levels can be tuned in one place.

Changed

• src/display.rs statechart restructured:
  • Splash gains entry: set_bright plus an action-only on(after 10s) => set_dim handler so the splash bright window is time-scoped without disturbing the LM↔Info alternation.
  • Dashboard Listening and Transmitting each gain a nested *Bright substate owning the entry: set_bright action. Packet handlers moved into the leaves and target the leaf's *Bright — sibling-to-sibling within the leaf restarts the 3 s timer without re-entering the leaf itself (paint / 1 s sparkline timer preserved). The 3 s timeout handler fires set_dim as an action and up-transitions to the leaf, parking the machine at the leaf with no active child.
• On.on(CmdReset) now targets LearnMore directly rather than Splash. Under hsmc 0.2 up-transition semantics, targeting Splash from within Splash.LearnMore (USB-disconnect race path) would only unwind below Splash and park with no active child, leaving the LM↔Info alternation timer dead and the QR frozen on screen.
• LoRaBoard::DisplayDriver trait bound extended with + DisplayBrightness so brightness is part of the board contract alongside DrawTarget<Color = BinaryColor>.

Fixed

• Elecrow ThinkNode-M2 board doc corrected: the shipping revision carries a WCH CH340K USB-UART bridge (USB 1a86:7522), not a Silicon Labs CP2102. just flash elecrow_thinknode_m2 now matches the CH340K / CH340 VID:PIDs directly instead of falling through to espflash auto-detect.

Dependencies

• hsmc bumped to 0.2 to pick up the up-transition fix (transition to an already-active ancestor unwinds only the subtree strictly below the target; no exit/entry on the target; no default descent).

[1.1.0] - 2026-04-22

Small but high-value behavior change: SET_CONFIG issued while the radio is in continuous RX no longer drops the radio (and the OLED) back to idle. The radio now auto-re-arms RX with the new modulation once reconfiguration completes, matching DongLoRa Protocol 1.1's §3.5 / §6.3 amendments.

Changed

• src/radio.rs: inside state Receiving, add on(ConfigApplied) => ResumingRx to shadow the parent Configured state's on(ConfigApplied) => Idle handler. The reconfigure path now runs apply_set_config → ConfigApplied → ResumingRx.entry: try_start_rx_hw → StartRxOk → Receiving without ever entering Idle.
• The OLED's Dashboard → Splash transition was previously driven by RadioEvent::Idle firing on Configured.Idle.entry. That event no longer fires during a SET_CONFIG-from-Receiving sequence, so the display stays on Dashboard.

Dependencies

• donglora-protocol bumped to 1.1.0 (spec-only change; matches the new normative text the firmware now implements).

Use-case unlock

• Scanner / time-division / dynamic-modulation workflows that rotate LoRa parameters mid-RX no longer need to re-issue RX_START after every SET_CONFIG. One call, radio continues to receive.

[1.0.0] - 2026-04-22

The 1.0 release. Firmware now speaks DongLoRa Protocol v2 end to end, depends on the freshly-published donglora-protocol 1.0.0 and hsmc 0.1.0 from crates.io, and ships GitHub Release binaries for every supported board.

Breaking

• DongLoRa Protocol v2 wire format (wire-incompatible with 0.x clients and firmware). Every type_id, tag-correlation rule, and field layout follows PROTOCOL.md v1.0.
• Host framing replaced. src/host/framing.rs now drives a streaming FrameDecoder from donglora-protocol and emits (type_id, tag, payload) frames; the 0.x COBS-per-response shim is gone.
• Radio task reshape. src/radio.rs emits v2 TX_DONE / SetConfigResult / RxPayload / RxOrigin shapes directly; no 0.x translation layer remains.

Changed

• hsmc switched from path-dep on the local workspace to version = "0.1.0" from crates.io.
• donglora-protocol switched from path-dep on ../protocol to version = "1.0.0" from crates.io; firmware builds are now reproducible from a clean checkout with no sibling repo required.
• PROTOCOL.md updated to the DongLoRa Protocol v2 normative spec, kept byte-for-byte in sync with the donglora-protocol crate's copy.

Infrastructure

• Cargo.toml repository + homepage now point at the canonical https://github.com/donglora/firmware (the swaits/donglora repo is archived).

[0.5.0] - 2026-04-16

Added

• BLE soft-mesh multiplexer design document (BLE_MUX_DESIGN_DOC.md) — specification for turning a dongle from a 1:1 USB device into a shared near-field radio gateway for multiple BLE-attached phones. Three-phase rollout (v1 MVP, v2 hardening, v3 multi-dongle mesh) with regulatory duty-cycle and TX-access-control enforcement from v1. Targets nRF52840 first; ESP32-S3 reserved for v2.
• debug-checkpoint cargo feature with a dedicated debug_blink task and a latching atomic checkpoint — LED-pattern diagnostic for UART-only boards where defmt output would corrupt the host protocol. Zero footprint when the feature is off.

Changed

• Radio task rewritten as an hsmc statechart (Unconfigured / Configured.{Idle, StartingRx, Receiving, ResumingRx, Transmitting.{FromIdle, FromRx}}). The main loop is now a single machine.run().await; command reading, packet RX, and TX are state-scoped during: activities. Post-TX RX re-arm is modeled as state identity (TransmittingFromRx → ResumingRx) instead of a was_receiving flag.
• Display task rewritten as an hsmc statechart (Off / On.{Splash.{LearnMore, Info}, Dashboard.{Listening, Transmitting}}). The 5 s splash alternation and 1 s sparkline tick use on(after …) / on(every …) transitions — no external timer task.
• USB host task now carries a small hsmc statechart (Disconnected / Connected) whose entry/exit actions handle display wake, radio StopRx, and display reset — replacing the open-coded was_connected edge detector.
• Radio → Display channel switched from a RadioStatus watch to a typed RadioEvent queue. The radio emits discrete EnteredRx / EnteredTx / Idle / PacketRx / PacketTx / ConfigChanged events; downstream consumers observe transitions directly rather than diffing snapshots.
• Wire protocol types and COBS framing moved out of firmware into the shared donglora-protocol crate (path dep on ../protocol). Firmware src/protocol.rs is now a re-export shim preserving every call site; src/host/framing.rs keeps only the embassy-specific route_command.

Fixed

• USB disconnect recovery: on a read error the DTR-edge-detect branch now runs unconditionally (was early-continuing in some paths, starving the display-reset / radio-stop handoff).

[0.4.0] - 2026-04-11

Added

• ELECROW ThinkNode-M2 board support (ESP32-S3 + SX1262 + 1.3" SH1106 OLED via CP2102 UART bridge, 1000 mAh Li-Po handheld)
  • Pin map verified against Meshtastic's variants/esp32s3/ELECROW-ThinkNode-M2
  • DIO3 TCXO driven at 3.3 V (not 1.8 V like Heltec)
  • Dedicated LORA_POWER_EN (GPIO48) sequenced HIGH before SPI init
  • VEXT_ENABLE (GPIO46) is active HIGH — opposite polarity from Heltec
  • Reuses the existing async SH1106 driver at I2C address 0x3C

Changed

• hal::esp32s3::{init_spi, init_i2c} and board::esp32s3::init_radio are now generic over GPIO type, so ESP32-S3 boards with different pin assignments can share the helpers.
• board::esp32s3::init_radio takes a TcxoCtrlVoltage parameter instead of hardcoding Ctrl1V8 — needed for ThinkNode-M2's 3.3 V TCXO.
• SSD1306 display items in board::esp32s3 are now cfg-gated to Heltec boards (ThinkNode-M2 supplies its own SH1106 create_display).
• justfile uses cargo +esp for Xtensa targets instead of cargo +nightly with a RUSTC=esp override — the self-contained esp toolchain keeps its cargo, rustc, and rust-src versions aligned. Public nightly's rust-src had drifted ahead of the esp fork, breaking -Zbuild-std.
• Migrated to embassy-executor 0.10 and embassy-rp 0.10
• ESP crates (esp-hal, esp-rtos, esp-backtrace, esp-println) patched from esp-rs/esp-hal main branch until esp-rtos publishes with 0.10 support
• Adapted to embassy-executor 0.10 SpawnToken API (task functions now return Result<SpawnToken, SpawnError>, Spawner::spawn no longer returns Result)
• Adapted to esp-hal main branch API changes: efuse::base_mac_address(), esp_rtos::start now requires SoftwareInterrupt, embassy-rp SPI constructor now requires DMA interrupt bindings
• just check now runs clippy with -D warnings instead of plain cargo check
• Rust toolchain bumped to 1.94 in mise.toml

Fixed

• core::mem::forget(output) pattern in ESP32-S3 board files is now let _vext = Output::new(...) — current esp-hal makes Output non-Drop, which made forget a no-op and tripped clippy's forget_non_drop lint.
• UART boards (heltec_v3_uart) display stuck on splash screen after boot. Host task sent DisplayCommand::Reset (which sets disconnected=true) instead of DisplayCommand::On. UART has no DTR, so nothing ever cleared it.

[0.3.0] - 2026-04-10

Added

• Waveshare RP2040-LoRa board support (RP2040 + SX1262, no OLED, LED on GPIO25)
  • First RP2040 board — third MCU family after ESP32-S3 and nRF52840
  • New hal/rp2040.rs module with MCU primitives (SPI, USB, flash unique ID)
  • USB-C via FPC ribbon cable to adapter board
  • PE4259 antenna switch on GPIO17, 850-930 MHz (HF)

Changed

• cortex-m-rt/set-vtor moved from global dependency to per-board feature (Cortex-M0+ has no VTOR register)
• build.rs memory.x selection is now target-aware (thumbv6m vs thumbv7em)

[0.2.1] - 2026-04-07

Fixed

• Display stuck on status screen after USB disconnect (stale radio status updates re-rendered dashboard over splash because disconnected flag was not set in the Reset handler)
• Radio left running after host disconnect, now sends StopRx when DTR drops
• System deadlock when host app closes serial port while radio is receiving (unsolicited responses in radio task now use try_send to avoid blocking on a full response channel)
• LED orphaned if OLED display initialization fails (display task now falls back to a LED-only event loop instead of returning early)

[0.2.0] - 2026-04-07

Added

• Wio Tracker L1 board support (nRF52840 + SX1262, SH1106 OLED)
• LED blink on packet activity: brief flash on RX and TX when display is on
  • RX brightness scales with SNR (stronger signal = brighter)
  • Works on all boards with a user LED (Heltec V3/V4, Wio Tracker)
• Native USB CDC-ACM support for Heltec V3 (requires hardware mod: solder R29/R3)
• heltec_v3_uart feature for stock (unmodified) V3 boards via CP2102 bridge
• RgbLed trait and SimpleLed driver for GPIO-based LEDs
• LoRaBoard trait with full associated types (RadioParts, CommParts, DisplayParts, DisplayDriver, LedDriver) and BoardParts<R, C, D, L> struct

Changed

• Major firmware architecture reorganization:
  • hal/ module for MCU-specific primitives (ESP32-S3, nRF52840)
  • driver/ module for hardware peripheral drivers (SH1106, SimpleLed)
  • host/ module for unified USB/UART communication with internal cfg dispatch
  • board/ contains only board definitions — no MCU helpers or drivers mixed in
  • Board files are declarative wiring diagrams calling hal primitives
• run() function has zero board-specific conditional compilation
• Display init moved to board layer (create_display()) — display task has no cfg
• Flattened radio/ and display/ directories (no single-file directories)
• build.rs auto-discovers boards by content (implements LoRaBoard) and helper modules by use super:: imports — no exclusion lists
• check and clippy commands now use --release profile
• Deduplicated USB/UART protocol framing (shared CobsDecoder + route_command)
• Removed ErrorCode::CrcError (SX1262 silently drops bad-CRC packets)

Fixed

• Display stuck on splash screen for UART boards (disconnected flag started true)

[0.1.0] - 2026-03-15

Added

• Transparent LoRa radio over USB CDC-ACM (VID 1209, PID 5741)
• COBS-framed fixed-size LE binary protocol (9 commands, 7 responses)
• Radio configuration: frequency, bandwidth, spreading factor, coding rate, TX power
• Continuous RX mode with RSSI/SNR per packet
• Single-shot TX with optional per-packet config override
• SSD1306 OLED display support with status dashboard
  • Radio state, frequency, modulation parameters
  • Packet counters (RX/TX)
  • RSSI sparkline (1-minute history, TX shown as dotted bars)
  • Combined splash/waiting screen on disconnect
• Auto-detect USB host connect/disconnect via DTR
• Config validation against per-board hardware limits
• TX_POWER_MAX sentinel (-128): auto-use the board's maximum TX power
• Board support: Heltec V3, Heltec V4, RAK WisBlock 4631
• Python host library (donglora on PyPI) with pip install and donglora-mux CLI
• USB multiplexer for sharing one dongle with multiple applications
• Two-way LoRa bridge over TCP (examples/lora_bridge.py)

Technical

• Embassy async runtime (no threads, CPU sleeps when idle)
• Zero-config: boots and waits for host commands
• Protocol-agnostic: firmware has no opinion about what you transmit
• Tasks never panic: all errors reported to host or logged
• Board abstraction: one .rs file + one Cargo feature per board