swaits
7fca5fcb50
ESP32-S3 + SX1262 + SH1106 OLED + AXP2101 PMIC, native USB-C. The AXP2101 PMIC gates power to the LoRa chip and the OLED. Without its init sequence (ALDO3 = 3.3 V for LoRa, ALDO1 = 3.3 V for OLED) the SX1262 never responds on SPI and radio init fails. Pin map verified against MeshCore's variants/lilygo_tbeam_supreme_SX1262. PMIC lives on a dedicated I²C1 bus (SDA=42, SCL=41) separate from the SH1106 on I²C0 (SDA=17, SCL=18); I²C1 is used blocking for a one-shot init and then dropped. TCXO at 1.6 V via DIO3. New src/driver/axp.rs holds the AXP2101 init sequence — kept minimal (only the LoRa + OLED rails), since DongLoRa is a LoRa-over-USB bridge and every other rail (GPS, BME280, IMU, SD, batt ADC) is out of scope.
DongLoRa Firmware
Embedded Rust firmware for DongLoRa boards. Exposes the LoRa radio over USB CDC-ACM using a COBS-framed binary protocol.
Building
just setup # one-time toolchain install
just build heltec_v4 # build for a specific board
just flash heltec_v4 # build + flash
just check-all # compile-check all boards
just clippy heltec_v4 # lint
just test # host-side protocol unit tests
All commands are run from the firmware/ directory.
Supported Boards
| Board | Feature | MCU | Radio | USB | Target |
|---|---|---|---|---|---|
| Heltec V3 | heltec_v3 |
ESP32-S3 | SX1262 | Native CDC-ACM | xtensa-esp32s3-none-elf |
| Heltec V3 (UART) | heltec_v3_uart |
ESP32-S3 | SX1262 | CP2102 bridge | xtensa-esp32s3-none-elf |
| Heltec V4 | heltec_v4 |
ESP32-S3 | SX1262 | Native CDC-ACM | xtensa-esp32s3-none-elf |
| ELECROW ThinkNode-M2 | elecrow_thinknode_m2 |
ESP32-S3 | SX1262 | CP2102 bridge | xtensa-esp32s3-none-elf |
| LilyGo T-Beam S3 Supreme | lilygo_tbeam_supreme |
ESP32-S3 | SX1262 | Native CDC-ACM | xtensa-esp32s3-none-elf |
| RAK WisBlock 4631 | rak_wisblock_4631 |
nRF52840 | SX1262 | Native CDC-ACM | thumbv7em-none-eabihf |
| Waveshare RP2040-LoRa | waveshare_rp2040_lora |
RP2040 | SX1262 | Native CDC-ACM | thumbv6m-none-eabi |
| Wio Tracker L1 | wio_tracker_l1 |
nRF52840 | SX1262 | Native CDC-ACM | thumbv7em-none-eabihf |
Heltec V3 USB Note
The default heltec_v3 build uses native USB CDC-ACM, which requires a
hardware modification to your board. Stock Heltec V3 boards route USB through a
CP2102 bridge chip to UART — the ESP32-S3's native USB pins (GPIO19/GPIO20) are
routed to header pins but not connected to the USB connector.
To enable native USB on a Heltec V3:
- Solder 0-ohm (or 22-ohm) resistors at pads R29 (D+) and R3 (D-)
- Disconnect the CP2102 from the USB connector's D+/D- lines (cut traces or remove the CP2102 bridge resistors)
After this mod, the board appears as /dev/ttyACM0 with the DongLoRa VID:PID
(1209:5741), just like the V4 and nRF boards.
If you have a stock (unmodified) V3, use heltec_v3_uart instead:
just build heltec_v3_uart
just flash heltec_v3_uart
This builds firmware that communicates via the CP2102 bridge (appears as
/dev/ttyUSB0).
Adding a Board
See src/board/PORTING.md.
Protocol
See PROTOCOL.md for the complete wire format specification.