swaits
f7bac5903c
Cap the splash board-name on a 128 px-wide OLED: every name must fit the FONT_5X8 fallback (25 ASCII chars) or the const_assert at the BOARD_NAME definition fails the build. At runtime, names that fit FONT_6X10 (21 chars) keep the primary font; longer names switch to FONT_5X8 instead of overflowing. Also drop the URL-line font on the "learn more" screen from FONT_5X8 to FONT_4X6 so "donglora.com" sits inside the 64 px column with breathing room instead of touching both edges.
DongLoRa Firmware
Embedded Rust firmware for DongLoRa boards. Exposes the LoRa radio over USB CDC-ACM using a COBS-framed binary protocol.
Building
just setup # one-time toolchain install
just build heltec_v4 # build for a specific board
just flash heltec_v4 # build + flash
just check-all # compile-check all boards
just clippy heltec_v4 # lint
just test # host-side protocol unit tests
All commands are run from the firmware/ directory.
Supported Boards
| Board | Feature | MCU | Radio | USB | Target |
|---|---|---|---|---|---|
| Heltec V3 | heltec_v3 |
ESP32-S3 | SX1262 | Native CDC-ACM | xtensa-esp32s3-none-elf |
| Heltec V3 (UART) | heltec_v3_uart |
ESP32-S3 | SX1262 | CP2102 bridge | xtensa-esp32s3-none-elf |
| Heltec V4 | heltec_v4 |
ESP32-S3 | SX1262 | Native CDC-ACM | xtensa-esp32s3-none-elf |
| ELECROW ThinkNode-M2 | elecrow_thinknode_m2 |
ESP32-S3 | SX1262 | CP2102 bridge | xtensa-esp32s3-none-elf |
| LilyGo T-Beam | lilygo_tbeam |
ESP32 | SX1276 | CP2102 bridge | xtensa-esp32-none-elf |
| LilyGo T-Beam S3 Supreme | lilygo_tbeam_supreme |
ESP32-S3 | SX1262 | Native CDC-ACM | xtensa-esp32s3-none-elf |
| RAK WisBlock 4631 | rak_wisblock_4631 |
nRF52840 | SX1262 | Native CDC-ACM | thumbv7em-none-eabihf |
| Waveshare RP2040-LoRa | waveshare_rp2040_lora |
RP2040 | SX1262 | Native CDC-ACM | thumbv6m-none-eabi |
| Wio Tracker L1 | wio_tracker_l1 |
nRF52840 | SX1262 | Native CDC-ACM | thumbv7em-none-eabihf |
Heltec V3 USB Note
The default heltec_v3 build uses native USB CDC-ACM, which requires a
hardware modification to your board. Stock Heltec V3 boards route USB through a
CP2102 bridge chip to UART — the ESP32-S3's native USB pins (GPIO19/GPIO20) are
routed to header pins but not connected to the USB connector.
To enable native USB on a Heltec V3:
- Solder 0-ohm (or 22-ohm) resistors at pads R29 (D+) and R3 (D-)
- Disconnect the CP2102 from the USB connector's D+/D- lines (cut traces or remove the CP2102 bridge resistors)
After this mod, the board appears as /dev/ttyACM0 with the DongLoRa VID:PID
(1209:5741), just like the V4 and nRF boards.
If you have a stock (unmodified) V3, use heltec_v3_uart instead:
just build heltec_v3_uart
just flash heltec_v3_uart
This builds firmware that communicates via the CP2102 bridge (appears as
/dev/ttyUSB0).
Adding a Board
See src/board/PORTING.md.
Protocol
See PROTOCOL.md for the complete wire format specification.