chore: release 1.3.0

feat(boards): LilyGo T-Beam (classic) support
First classic-ESP32 (non-S3) board in the firmware, and first SX127x radio. ESP32 + SX1276 + SSD1306 OLED + AXP192 PMIC, CP2102 USB-UART bridge. Pin map verified from MeshCore variants/lilygo_tbeam_SX1276. The AXP192 gates power to the LoRa chip and OLED. Its I²C bus is shared with the display, so the firmware builds I²C0 in blocking mode first for the PMIC init, then converts the same handle to async and hands it to the display task — avoids double-consuming the peripheral. Lora-phy's Sx127x support drives DIO0 as the sole IRQ (SX127x has no BUSY line); the chip runs from a crystal, tx_boost routes +20 dBm through PA_BOOST. The `esp-hal` / `esp-rtos` / `esp-backtrace` / `esp-println` deps have been restructured so the chip flavour (esp32 vs esp32s3) is selected at the per-board feature level instead of baked into the dep lines. This keeps the existing S3 boards building on esp32s3 while the new T-Beam feature selects classic esp32 via the same dependency set. LoRaBoard gains supported_sf_bitmap() / supported_bw_bitmap() methods (with SX126x defaults) so the T-Beam can report SF6–SF12 via GET_INFO — the SX1276 has no SF5. radio_chip_id() reports 0x0011 per donglora-protocol RadioChipId::Sx1276. freq_range_hz widens to the SX1276 datasheet span of 137 MHz–1020 MHz. New modules: - src/hal/esp32.rs — classic-ESP32 MCU primitives - src/board/esp32.rs — Sx127x radio + SSD1306 display pipe - src/board/lilygo_tbeam.rs — the board file - src/driver/axp.rs — AXP192 init added alongside AXP2101
2026-04-23 12:50:03 -06:00 · 2026-04-23 10:42:42 -06:00 · 2026-04-23 10:29:48 -06:00 · 2026-04-22 23:59:44 -06:00 · 2026-04-22 23:59:12 -06:00 · 2026-04-22 20:50:11 -06:00
25 changed files with 4081 additions and 993 deletions
@@ -7,6 +7,215 @@ and this project adheres to [Semantic Versioning](https://semver.org/).

 ## [Unreleased]

+## [1.3.0] - 2026-04-23
+
+### Added
+
+- LilyGo T-Beam S3 Supreme board support (ESP32-S3 + SX1262 + SH1106
+  OLED + AXP2101 PMIC, native USB-C).
+  - Pin map verified against MeshCore's
+    `variants/lilygo_tbeam_supreme_SX1262`.
+  - New `src/driver/axp.rs` module with an AXP2101 init sequence
+    (ALDO3 = 3.3 V LoRa, ALDO1 = 3.3 V OLED). The PMIC gates LoRa and
+    display power — without it the SX1262 never responds on SPI.
+  - PMIC lives on a dedicated I²C1 bus (SDA=42, SCL=41), separate
+    from the SH1106 on I²C0 (SDA=17, SCL=18). I²C1 is used blocking
+    for a one-shot init and then dropped.
+  - TCXO driven at 1.6 V via DIO3 (MeshCore uses the same).
+- LilyGo T-Beam (classic) board support (ESP32 + SX1276 + SSD1306
+  OLED + AXP192 PMIC, CP2102 USB-UART bridge). This is the first
+  board in the firmware on classic ESP32 (non-S3) and the first on
+  the SX127x radio family.
+  - Pin map verified against MeshCore's `variants/lilygo_tbeam_SX1276`.
+  - New `src/hal/esp32.rs` (classic-ESP32 MCU primitives, peripheral
+    DMA via `DMA_SPI2`) and `src/board/esp32.rs` (SX1276 radio helper
+    + SSD1306 display pipe).
+  - AXP192 init added to `src/driver/axp.rs`: DCDC1 = 3.3 V for the
+    OLED, LDO2 = 3.3 V for the SX1276 PA_BOOST rail. Shares the
+    OLED I²C bus (SDA=21, SCL=22); the I²C instance is built in
+    blocking mode for PMIC init and converted to async for the
+    display task.
+  - SX127x support via lora-phy 3's `Sx127x<Sx1276>` +
+    `GenericSx127xInterfaceVariant` (DIO0 as the sole IRQ; no
+    BUSY line on SX127x). XTAL clocked (no TCXO), `tx_boost = true`
+    for the PA_BOOST path.
+  - `LoRaBoard` trait gains `supported_sf_bitmap()` and
+    `supported_bw_bitmap()` methods with SX126x defaults
+    (`0x1FE0`, `0x03FF`). T-Beam classic overrides SF to `0x1FC0`
+    (SF6–SF12) — the SX1276 has no SF5.
+  - `radio_chip_id()` reports `0x0011` (`RadioChipId::Sx1276`) and
+    `freq_range_hz()` widens to 137 MHz–1020 MHz per the SX1276
+    datasheet.
+
+### Changed
+
+- `Cargo.toml`: the `esp32s3` chip feature has been moved out of
+  the `esp-hal` / `esp-rtos` / `esp-backtrace` / `esp-println`
+  dependency lines and into each ESP board's feature list (as
+  `esp-hal/esp32s3`, etc.). This lets `lilygo_tbeam` select the
+  classic `esp32` chip flavour from the same dependency set.
+
+## [1.2.1] - 2026-04-23
+
+### Fixed
+
+- **Radio no longer drops to Idle mid-RX-session on transient failures.**
+  Extends the v1.1.0 invariant ("`SET_CONFIG` during RX auto-re-arms")
+  to all failure paths that can occur while a client has RX active:
+  - `Receiving.on(RxFailed) => Idle` now transitions to `ResumingRx`
+    instead of `Idle`. A transient `next_packet` error re-arms the chip
+    rather than ending the RX session.
+  - `TransmittingFromRx.on(TransmitFailed) => Idle` now transitions to
+    `ResumingRx`. TX failure during an active RX session returns
+    `TX_FAILED` to the caller and resumes RX, matching the shape of the
+    adjacent `ChannelBusy` handler.
+  - `ResumingRx.on(StartRxFailed) => Idle` is now a bounded retry
+    (5 × 25 ms backoff via a new `bump_resume_retries` action and a
+    `ResumeRxRetry` / `ResumeRxExhausted` pair of internal events).
+    The chip only lands in `Idle` after exhausting the retry budget —
+    which means it's genuinely wedged and needs reconfiguring.
+
+  Visible effect: the OLED dashboard no longer bounces to Splash when
+  `ai-bot` (or any other client that TXes while RX is running) sends a
+  packet. Previously any of the three transitions above would fire
+  `RadioEvent::Idle`, which the display uses as its `Dashboard → Splash`
+  trigger; the radio would land in `Idle` with no client aware enough
+  to re-send `RX_START`, stranding the dashboard until the session was
+  manually torn down and restarted.
+
+- Removed `announce_rx_failed` helper action: its only purpose was
+  emitting `RadioEvent::Idle` on the now-deleted `Receiving.on(RxFailed)
+  => Idle` edge. No replacement needed — `ResumingRx` handles recovery
+  silently.
+
+## [1.2.0] - 2026-04-22
+
+### Added
+
+- **OLED auto-dim after inactivity.** The display is bright on any
+  activity — splash entry, mode change into a dashboard leaf, packet
+  RX/TX — and dims after a short idle window. Splash holds bright for
+  10 s, then drops to dim while the LearnMore / Info carousel keeps
+  alternating. The dashboard stays bright for 3 s after the last
+  packet or mode change, then dims in place without changing
+  Listening/Transmitting state. Cross-leaf TX↔RX hops transition
+  bright→bright with no intermediate dim — `set_dim` is fired as an
+  action by the 3 s timer handler rather than as a sibling `exit:`
+  action, so mode-change leaf-crossings never see a flash.
+- `DisplayBrightness` trait in `src/driver/mod.rs` unifies the
+  two-level backlight API across the `ssd1306` crate's `Ssd1306Async`
+  and the in-tree `Sh1106` driver. Contrast values centralized as
+  `CONTRAST_BRIGHT` (`0xFF`) and `CONTRAST_DIM` (`0x08`) constants so
+  the two levels can be tuned in one place.
+
+### Changed
+
+- `src/display.rs` statechart restructured:
+  - `Splash` gains `entry: set_bright` plus an action-only
+    `on(after 10s) => set_dim` handler so the splash bright window
+    is time-scoped without disturbing the LM↔Info alternation.
+  - `Dashboard` `Listening` and `Transmitting` each gain a nested
+    `*Bright` substate owning the `entry: set_bright` action. Packet
+    handlers moved into the leaves and target the leaf's `*Bright` —
+    sibling-to-sibling within the leaf restarts the 3 s timer without
+    re-entering the leaf itself (paint / 1 s sparkline timer
+    preserved). The 3 s timeout handler fires `set_dim` as an action
+    and up-transitions to the leaf, parking the machine at the leaf
+    with no active child.
+- `On.on(CmdReset)` now targets `LearnMore` directly rather than
+  `Splash`. Under hsmc 0.2 up-transition semantics, targeting
+  `Splash` from within `Splash.LearnMore` (USB-disconnect race path)
+  would only unwind below `Splash` and park with no active child,
+  leaving the LM↔Info alternation timer dead and the QR frozen on
+  screen.
+- `LoRaBoard::DisplayDriver` trait bound extended with
+  `+ DisplayBrightness` so brightness is part of the board contract
+  alongside `DrawTarget<Color = BinaryColor>`.
+
+### Fixed
+
+- Elecrow ThinkNode-M2 board doc corrected: the shipping revision
+  carries a WCH CH340K USB-UART bridge (USB `1a86:7522`), not a
+  Silicon Labs CP2102. `just flash elecrow_thinknode_m2` now matches
+  the CH340K / CH340 VID:PIDs directly instead of falling through
+  to espflash auto-detect.
+
+### Dependencies
+
+- `hsmc` bumped to `0.2` to pick up the up-transition fix (transition
+  to an already-active ancestor unwinds only the subtree strictly
+  below the target; no exit/entry on the target; no default descent).
+
+## [1.1.0] - 2026-04-22
+
+Small but high-value behavior change: `SET_CONFIG` issued while the
+radio is in continuous RX no longer drops the radio (and the OLED)
+back to idle. The radio now auto-re-arms RX with the new modulation
+once reconfiguration completes, matching DongLoRa Protocol 1.1's
+§3.5 / §6.3 amendments.
+
+### Changed
+
+- `src/radio.rs`: inside `state Receiving`, add `on(ConfigApplied)
+  => ResumingRx` to shadow the parent `Configured` state's
+  `on(ConfigApplied) => Idle` handler. The reconfigure path now
+  runs `apply_set_config` → `ConfigApplied` → `ResumingRx.entry:
+  try_start_rx_hw` → `StartRxOk` → `Receiving` without ever
+  entering `Idle`.
+- The OLED's `Dashboard → Splash` transition was previously driven
+  by `RadioEvent::Idle` firing on `Configured.Idle.entry`. That
+  event no longer fires during a SET_CONFIG-from-Receiving
+  sequence, so the display stays on Dashboard.
+
+### Dependencies
+
+- `donglora-protocol` bumped to `1.1.0` (spec-only change; matches
+  the new normative text the firmware now implements).
+
+### Use-case unlock
+
+- Scanner / time-division / dynamic-modulation workflows that
+  rotate LoRa parameters mid-RX no longer need to re-issue
+  `RX_START` after every `SET_CONFIG`. One call, radio continues
+  to receive.
+
+## [1.0.0] - 2026-04-22
+
+The 1.0 release. Firmware now speaks DongLoRa Protocol v2 end to end,
+depends on the freshly-published `donglora-protocol` 1.0.0 and `hsmc`
+0.1.0 from crates.io, and ships GitHub Release binaries for every
+supported board.
+
+### Breaking
+
+- **DongLoRa Protocol v2 wire format** (wire-incompatible with 0.x
+  clients and firmware). Every `type_id`, tag-correlation rule, and
+  field layout follows `PROTOCOL.md` v1.0.
+- **Host framing replaced.** `src/host/framing.rs` now drives a
+  streaming `FrameDecoder` from `donglora-protocol` and emits
+  `(type_id, tag, payload)` frames; the 0.x COBS-per-response shim is
+  gone.
+- **Radio task reshape.** `src/radio.rs` emits v2 `TX_DONE` /
+  `SetConfigResult` / `RxPayload` / `RxOrigin` shapes directly; no 0.x
+  translation layer remains.
+
+### Changed
+
+- `hsmc` switched from path-dep on the local workspace to
+  `version = "0.1.0"` from crates.io.
+- `donglora-protocol` switched from path-dep on `../protocol` to
+  `version = "1.0.0"` from crates.io; firmware builds are now
+  reproducible from a clean checkout with no sibling repo required.
+- `PROTOCOL.md` updated to the DongLoRa Protocol v2 normative spec,
+  kept byte-for-byte in sync with the `donglora-protocol` crate's
+  copy.
+
+### Infrastructure
+
+- Cargo.toml `repository` + `homepage` now point at the canonical
+  `https://github.com/donglora/firmware` (the `swaits/donglora`
+  repo is archived).
+
 ## [0.5.0] - 2026-04-16

 ### Added
@@ -486,7 +486,7 @@ dependencies = [

 [[package]]
 name = "donglora"
-version = "0.5.0"
+version = "1.3.0"
 dependencies = [
 "cfg-if",
 "cortex-m",
@@ -527,7 +527,9 @@ dependencies = [

 [[package]]
 name = "donglora-protocol"
-version = "0.1.0"
+version = "1.1.0"
+source = "registry+https://github.com/rust-lang/crates.io-index"
+checksum = "6bae9e9e5a8cebc6b4167f9ef696b61ce25b94c6d8283dbe1b2e97075a481b9d"
 dependencies = [
 "defmt 1.0.1",
 "heapless 0.9.2",
@@ -1058,6 +1060,8 @@ dependencies = [
 "rand_core 0.6.4",
 "rand_core 0.9.5",
 "riscv",
+ "sha1",
+ "sha2",
 "strum",
 "ufmt-write",
 "xtensa-lx",
@@ -1114,6 +1118,7 @@ dependencies = [
 "cfg-if",
 "document-features",
 "esp-metadata-generated",
+ "esp32",
 "esp32s3",
 ]

@@ -1389,6 +1394,7 @@ version = "0.9.2"
 source = "registry+https://github.com/rust-lang/crates.io-index"
 checksum = "2af2455f757db2b292a9b1768c4b70186d443bcb3b316252d6b540aec1cd89ed"
 dependencies = [
+ "defmt 1.0.1",
 "hash32",
 "stable_deref_trait",
 ]
@@ -1401,7 +1407,9 @@ checksum = "2304e00983f87ffb38b55b444b5e3b60a884b5d30c0fca7d82fe33449bbe55ea"

 [[package]]
 name = "hsmc"
-version = "0.1.0"
+version = "0.2.0"
+source = "registry+https://github.com/rust-lang/crates.io-index"
+checksum = "960effec6ded897c013d5cde8fb7f09bf0137e783efc4c2e0346092a2941c46e"
 dependencies = [
 "embassy-futures",
 "embassy-sync 0.8.0",
@@ -1412,7 +1420,9 @@ dependencies = [

 [[package]]
 name = "hsmc-macros"
-version = "0.1.0"
+version = "0.2.0"
+source = "registry+https://github.com/rust-lang/crates.io-index"
+checksum = "3e1933eea1e95edb4fa03688f969f0a1ffabc4f16fc396b40ead6bedd5c4bdff"
 dependencies = [
 "proc-macro2",
 "quote",
@@ -2197,6 +2207,28 @@ dependencies = [
 "unsafe-libyaml",
 ]

+[[package]]
+name = "sha1"
+version = "0.10.6"
+source = "registry+https://github.com/rust-lang/crates.io-index"
+checksum = "e3bf829a2d51ab4a5ddf1352d8470c140cadc8301b2ae1789db023f01cedd6ba"
+dependencies = [
+ "cfg-if",
+ "cpufeatures",
+ "digest",
+]
+
+[[package]]
+name = "sha2"
+version = "0.10.9"
+source = "registry+https://github.com/rust-lang/crates.io-index"
+checksum = "a7507d819769d01a365ab707794a4084392c824f54a7a6a7862f8c3d0892b283"
+dependencies = [
+ "cfg-if",
+ "cpufeatures",
+ "digest",
+]
+
 [[package]]
 name = "sha2-const-stable"
 version = "0.1.0"
@@ -3,13 +3,14 @@ members = ["."]

 [package]
 name = "donglora"
-version = "0.5.0"
+version = "1.3.0"
 edition = "2021"
 build = "build.rs"
 authors = ["Stephen Waits <steve@waits.net>"]
 license = "MIT"
 description = "Transparent LoRa radio over USB — plug in a board, talk LoRa from your host"
-repository = "https://github.com/swaits/donglora"
+repository = "https://github.com/donglora/firmware"
+homepage = "https://github.com/donglora/firmware"
 keywords = ["lora", "radio", "embedded", "usb", "firmware"]
 categories = ["embedded", "hardware-support", "no-std"]

@@ -29,8 +30,8 @@ embassy-usb = { version = "0.6", features = ["defmt"] }
 embassy-usb-driver = "0.2"
 ucobs = { version = "0.3", features = ["legacy-msrv"] }
 heapless = "0.9"
-donglora-protocol = { path = "../protocol" }
-hsmc = { path = "../../hsmc/hsmc", default-features = false, features = ["embassy"] }
+donglora-protocol = "1"
+hsmc = { version = "0.2", default-features = false, features = ["embassy"] }
 lora-phy = "3.0"
 portable-atomic = { version = "1", optional = true, default-features = false, features = ["critical-section"] }
 static_cell = "2.1"
@@ -44,22 +45,20 @@ ssd1306 = { version = "0.10", features = ["async"] }
 embedded-io-async = "0.7"
 embassy-futures = "0.1"

-# ESP32-S3 (Heltec V3) — requires esp toolchain (espup)
+# Xtensa ESP crates — requires esp toolchain (espup). The chip feature
+# (esp32 / esp32s3) is selected per board via the board-level feature flag
+# below, so the same dep lines support both classic ESP32 and ESP32-S3.
 esp-backtrace = { version = "0.18", optional = true, features = [
-  "esp32s3",
  "panic-handler",
  "defmt",
 ] }
 esp-hal = { version = "1.0", optional = true, features = [
-  "esp32s3",
  "unstable",
 ] }
 esp-println = { version = "0.16", optional = true, features = [
-  "esp32s3",
  "defmt-espflash",
 ] }
 esp-rtos = { version = "0.2", optional = true, features = [
-  "esp32s3",
  "embassy",
 ] }

@@ -109,6 +108,10 @@ heltec_v3 = [
  "dep:esp-hal",
  "dep:esp-println",
  "dep:esp-rtos",
+  "esp-backtrace/esp32s3",
+  "esp-hal/esp32s3",
+  "esp-println/esp32s3",
+  "esp-rtos/esp32s3",
 ]
 heltec_v3_uart = [
  "embassy",
@@ -116,6 +119,10 @@ heltec_v3_uart = [
  "dep:esp-hal",
  "dep:esp-println",
  "dep:esp-rtos",
+  "esp-backtrace/esp32s3",
+  "esp-hal/esp32s3",
+  "esp-println/esp32s3",
+  "esp-rtos/esp32s3",
 ]
 heltec_v4 = [
  "embassy",
@@ -123,6 +130,10 @@ heltec_v4 = [
  "dep:esp-hal",
  "dep:esp-println",
  "dep:esp-rtos",
+  "esp-backtrace/esp32s3",
+  "esp-hal/esp32s3",
+  "esp-println/esp32s3",
+  "esp-rtos/esp32s3",
 ]
 elecrow_thinknode_m2 = [
  "embassy",
@@ -130,6 +141,32 @@ elecrow_thinknode_m2 = [
  "dep:esp-hal",
  "dep:esp-println",
  "dep:esp-rtos",
+  "esp-backtrace/esp32s3",
+  "esp-hal/esp32s3",
+  "esp-println/esp32s3",
+  "esp-rtos/esp32s3",
+]
+lilygo_tbeam_supreme = [
+  "embassy",
+  "dep:esp-backtrace",
+  "dep:esp-hal",
+  "dep:esp-println",
+  "dep:esp-rtos",
+  "esp-backtrace/esp32s3",
+  "esp-hal/esp32s3",
+  "esp-println/esp32s3",
+  "esp-rtos/esp32s3",
+]
+lilygo_tbeam = [
+  "embassy",
+  "dep:esp-backtrace",
+  "dep:esp-hal",
+  "dep:esp-println",
+  "dep:esp-rtos",
+  "esp-backtrace/esp32",
+  "esp-hal/esp32",
+  "esp-println/esp32",
+  "esp-rtos/esp32",
 ]
 rak_wisblock_4631 = [
  "embassy",
@@ -24,6 +24,8 @@ All commands are run from the `firmware/` directory.
 | Heltec V3 (UART) | `heltec_v3_uart` | ESP32-S3 | SX1262 | CP2102 bridge | xtensa-esp32s3-none-elf |
 | Heltec V4 | `heltec_v4` | ESP32-S3 | SX1262 | Native CDC-ACM | xtensa-esp32s3-none-elf |
 | ELECROW ThinkNode-M2 | `elecrow_thinknode_m2` | ESP32-S3 | SX1262 | CP2102 bridge | xtensa-esp32s3-none-elf |
+| LilyGo T-Beam | `lilygo_tbeam` | ESP32 | SX1276 | CP2102 bridge | xtensa-esp32-none-elf |
+| LilyGo T-Beam S3 Supreme | `lilygo_tbeam_supreme` | ESP32-S3 | SX1262 | Native CDC-ACM | xtensa-esp32s3-none-elf |
 | RAK WisBlock 4631 | `rak_wisblock_4631` | nRF52840 | SX1262 | Native CDC-ACM | thumbv7em-none-eabihf |
 | Waveshare RP2040-LoRa | `waveshare_rp2040_lora` | RP2040 | SX1262 | Native CDC-ACM | thumbv6m-none-eabi |
 | Wio Tracker L1 | `wio_tracker_l1` | nRF52840 | SX1262 | Native CDC-ACM | thumbv7em-none-eabihf |
@@ -10,6 +10,8 @@ heltec_v3      := "heltec_v3 xtensa-esp32s3-none-elf esp32s3"
 heltec_v3_uart := "heltec_v3_uart xtensa-esp32s3-none-elf esp32s3"
 heltec_v4      := "heltec_v4 xtensa-esp32s3-none-elf esp32s3"
 elecrow_thinknode_m2 := "elecrow_thinknode_m2 xtensa-esp32s3-none-elf esp32s3"
+lilygo_tbeam         := "lilygo_tbeam xtensa-esp32-none-elf esp32"
+lilygo_tbeam_supreme := "lilygo_tbeam_supreme xtensa-esp32s3-none-elf esp32s3"
 rak_wisblock_4631  := "rak_wisblock_4631 thumbv7em-none-eabihf nRF52840_xxAA"
 wio_tracker_l1     := "wio_tracker_l1 thumbv7em-none-eabihf nRF52840_xxAA"
 waveshare_rp2040_lora := "waveshare_rp2040_lora thumbv6m-none-eabi rp2040"
@@ -18,7 +20,7 @@ builds_dir := "builds"
 version := `sed -n 's/^version = "\(.*\)"/\1/p' Cargo.toml`

 # All known boards
-boards := "heltec_v3 heltec_v3_uart heltec_v4 elecrow_thinknode_m2 rak_wisblock_4631 waveshare_rp2040_lora wio_tracker_l1"
+boards := "heltec_v3 heltec_v3_uart heltec_v4 elecrow_thinknode_m2 lilygo_tbeam lilygo_tbeam_supreme rak_wisblock_4631 waveshare_rp2040_lora wio_tracker_l1"

 # Install all required tools and toolchains
 setup:
@@ -77,7 +79,7 @@ flash board:
    @read -r feat target chip <<< "$(just _info {{board}})"; \
    case "$target" in \
        xtensa-*) \
-            port=$(just _find_port "303a:1001" "1209:5741" "10c4:ea60"); \
+            port=$(just _find_port "303a:1001" "1209:5741" "10c4:ea60" "1a86:7522" "1a86:7523"); \
            if [ -n "$port" ]; then \
                echo "Using $port"; \
                espflash flash -p "$port" "{{builds_dir}}/donglora-{{board}}-v{{version}}.elf"; \
@@ -214,6 +216,8 @@ _info name:
     elif [ "{{name}}" == "heltec_v3_uart" ]; then echo "{{heltec_v3_uart}}"; \
     elif [ "{{name}}" == "heltec_v4" ]; then echo "{{heltec_v4}}"; \
     elif [ "{{name}}" == "elecrow_thinknode_m2" ]; then echo "{{elecrow_thinknode_m2}}"; \
+     elif [ "{{name}}" == "lilygo_tbeam" ]; then echo "{{lilygo_tbeam}}"; \
+     elif [ "{{name}}" == "lilygo_tbeam_supreme" ]; then echo "{{lilygo_tbeam_supreme}}"; \
     elif [ "{{name}}" == "rak_wisblock_4631" ]; then echo "{{rak_wisblock_4631}}"; \
     elif [ "{{name}}" == "waveshare_rp2040_lora" ]; then echo "{{waveshare_rp2040_lora}}"; \
     elif [ "{{name}}" == "wio_tracker_l1" ]; then echo "{{wio_tracker_l1}}"; \
@@ -1,8 +1,8 @@
 //! ELECROW ThinkNode-M2 — ESP32-S3 Meshtastic handset with SH1106 OLED.
 //!
 //! Tamagotchi-form-factor handheld: ESP32-S3-WROOM-1-N4 + SX1262 + 1.3" SH1106
-//! OLED + CP2102 UART bridge + 1000 mAh Li-Po. Sold pre-loaded with Meshtastic;
-//! this firmware turns it into a DongLoRa radio bridge.
+//! OLED + WCH CH340K UART bridge + 1000 mAh Li-Po. Sold pre-loaded with
+//! Meshtastic; this firmware turns it into a DongLoRa radio bridge.
 //!
 //! Pin map (verified from Meshtastic's variants/esp32s3/ELECROW-ThinkNode-M2
 //! and PR meshtastic/firmware#6354):
@@ -11,7 +11,7 @@
 //!   LoRa pwr: GPIO48 (must be HIGH before any SPI traffic)
 //!   OLED:     I2C0 SDA=16, SCL=15, SH1106 @ 0x3C
 //!   VEXT:     GPIO46 (active HIGH — gates OLED supply)
-//!   UART:     TX=43, RX=44 via CP2102 bridge
+//!   UART:     TX=43, RX=44 via CH340K bridge (USB 1a86:7522)
 //!   LED:      GPIO6 (active HIGH indicator)
 //!
 //! Notable differences from the Heltec ESP32-S3 boards:
@@ -0,0 +1,103 @@
+//! Shared types and peripheral wiring for classic-ESP32 SX1276 boards.
+//!
+//! Counterpart to `board::esp32s3` for the SX126x line. Builds an
+//! `Sx127x<Sx1276>` driver from an already-initialized SPI bus plus the
+//! board's reset and DIO0 pins. SX127x has no `BUSY` line — DIO0 carries
+//! every IRQ (TX done, RX done, header valid, …) and lora-phy's
+//! `GenericSx127xInterfaceVariant` waits on it directly.
+
+use embassy_embedded_hal::shared_bus::asynch::spi::SpiDevice;
+use embassy_sync::blocking_mutex::raw::NoopRawMutex;
+use embassy_time::Delay;
+use esp_hal::gpio::{Input, InputConfig, InputPin, Level, Output, OutputConfig, OutputPin, Pull};
+
+use lora_phy::iv::GenericSx127xInterfaceVariant;
+use lora_phy::sx127x::{self, Sx127x};
+
+use crate::hal::esp32 as mcu;
+
+// ── Re-export MCU types ─────────────────────────────────────────────
+
+pub use mcu::{I2cBus as DisplayI2c, SpiBus};
+
+// ── Concrete peripheral types ───────────────────────────────────────
+
+type Nss = Output<'static>;
+type Iv = GenericSx127xInterfaceVariant<Output<'static>, Input<'static>>;
+type RadioSpiDevice = SpiDevice<'static, NoopRawMutex, SpiBus, Nss>;
+pub type RadioDriver = Sx127x<RadioSpiDevice, Iv, sx127x::Sx1276>;
+
+// ── Peripheral bundles ──────────────────────────────────────────────
+
+pub struct RadioParts {
+    pub driver: RadioDriver,
+    pub delay: Delay,
+}
+
+pub struct DisplayParts {
+    pub i2c: DisplayI2c,
+}
+
+// ── Display driver ──────────────────────────────────────────────────
+
+pub type DisplayDriver = ssd1306::Ssd1306Async<
+    ssd1306::prelude::I2CInterface<DisplayI2c>,
+    ssd1306::size::DisplaySize128x64,
+    ssd1306::mode::BufferedGraphicsModeAsync<ssd1306::size::DisplaySize128x64>,
+>;
+
+/// Construct and initialize an SSD1306 display from raw I²C.
+pub async fn create_display(i2c: DisplayI2c) -> Option<DisplayDriver> {
+    use ssd1306::mode::DisplayConfigAsync;
+    use ssd1306::prelude::{Brightness, DisplayRotation};
+    use ssd1306::size::DisplaySize128x64;
+    use ssd1306::{I2CDisplayInterface, Ssd1306Async};
+
+    let interface = I2CDisplayInterface::new(i2c);
+    let mut display = Ssd1306Async::new(interface, DisplaySize128x64, DisplayRotation::Rotate0)
+        .into_buffered_graphics_mode();
+
+    embassy_time::Timer::after_millis(100).await;
+    if display.init().await.is_err() {
+        defmt::error!("SSD1306 display init failed");
+        return None;
+    }
+    let _ = display.set_brightness(Brightness::BRIGHTEST).await;
+    Some(display)
+}
+
+// ── Shared peripheral init helpers ──────────────────────────────────
+
+/// Construct an SX1276 radio from an initialized SPI bus.
+///
+/// `dio0` is the primary IRQ (TX/RX done). The SX1276 module on the T-Beam
+/// runs from a crystal oscillator, not a TCXO, and power comes from the
+/// AXP192's PA_BOOST rail — `tx_boost = true` routes TX through the PA
+/// output for +20 dBm.
+pub fn init_radio(
+    spi_bus: &'static embassy_sync::mutex::Mutex<NoopRawMutex, SpiBus>,
+    nss_pin: impl OutputPin + 'static,
+    reset_pin: impl OutputPin + 'static,
+    dio0_pin: impl InputPin + 'static,
+) -> RadioParts {
+    let nss = Output::new(nss_pin, Level::High, OutputConfig::default());
+    let spi_device = SpiDevice::new(spi_bus, nss);
+
+    let reset = Output::new(reset_pin, Level::High, OutputConfig::default());
+    let dio0 = Input::new(dio0_pin, InputConfig::default().with_pull(Pull::Down));
+
+    let iv = GenericSx127xInterfaceVariant::new(reset, dio0, None, None)
+        .expect("SX1276 interface init");
+
+    let sx_config = sx127x::Config {
+        chip: sx127x::Sx1276,
+        tcxo_used: false,
+        tx_boost: true,
+        rx_boost: false,
+    };
+
+    RadioParts {
+        driver: Sx127x::new(spi_device, iv, sx_config),
+        delay: Delay,
+    }
+}
@@ -0,0 +1,137 @@
+//! LilyGo T-Beam (classic) — ESP32 + SX1276 + SSD1306 OLED + AXP192 PMIC.
+//!
+//! First-generation T-Beam. ESP32 (dual-core Xtensa LX6, no native USB),
+//! SX1276 module with XTAL (no TCXO), 128×64 SSD1306 OLED, AXP192 PMIC
+//! gating the LoRa and OLED rails, CP2102 USB-UART bridge for host I/O.
+//!
+//! The AXP192 shares an I²C bus with the OLED (SDA=21, SCL=22). PMIC init
+//! runs blocking on that bus first, then the same pins are re-initialized
+//! in async mode for the display task.
+//!
+//! Pin map (verified from MeshCore variants/lilygo_tbeam_SX1276/):
+//!   LoRa SPI:  SCK=5, MOSI=27, MISO=19, CS=18
+//!   LoRa ctl:  RESET=23, DIO0=26 (primary IRQ — SX127x has no BUSY)
+//!   OLED I²C:  SDA=21, SCL=22, SSD1306 @ 0x3C (shared with AXP192 @ 0x34)
+//!   UART host: TX=1, RX=3 via CP2102 bridge (USB 10c4:ea60)
+//!   LED:       GPIO4 (active HIGH — reuses MeshCore's P_LORA_TX_LED)
+//!
+//! GPS / battery / IMU / PCF8563 RTC are populated on the board but unused
+//! by this firmware.
+
+use esp_hal::gpio::{Level, Output, OutputConfig};
+use esp_hal::i2c::master::{Config as I2cConfig, I2c};
+
+use super::esp32;
+use super::traits::{BoardParts, LoRaBoard};
+use crate::driver::axp;
+use crate::driver::simple_led::SimpleLed;
+use crate::hal::esp32 as mcu;
+use crate::protocol::RadioChipId;
+
+pub use super::esp32::{create_display, DisplayDriver, DisplayParts, RadioDriver, RadioParts};
+
+// ── Concrete peripheral types ───────────────────────────────────────
+
+pub type UartDriver = esp_hal::uart::Uart<'static, esp_hal::Async>;
+pub type LedDriver = SimpleLed<Output<'static>>;
+
+// ── Peripheral bundles ──────────────────────────────────────────────
+
+pub struct UartParts {
+    pub driver: UartDriver,
+}
+
+// ── Board init ──────────────────────────────────────────────────────
+
+pub struct Board {
+    p: esp_hal::peripherals::Peripherals,
+}
+
+impl LoRaBoard for Board {
+    const NAME: &'static str = "LilyGo T-Beam";
+    // SX1276 PA_BOOST range per the datasheet: +2 dBm min, +20 dBm max.
+    const TX_POWER_RANGE: (i8, i8) = (2, 20);
+
+    type RadioParts = RadioParts;
+    type CommParts = UartParts;
+    type DisplayParts = DisplayParts;
+    type DisplayDriver = DisplayDriver;
+    type LedDriver = LedDriver;
+
+    fn init() -> Self {
+        let p = esp_hal::init(esp_hal::Config::default());
+        Self { p }
+    }
+
+    fn mac_address() -> [u8; 6] {
+        mcu::mac_address()
+    }
+
+    fn radio_chip_id() -> u16 {
+        RadioChipId::Sx1276.as_u16()
+    }
+
+    fn freq_range_hz() -> (u32, u32) {
+        // SX1276 tuning window per datasheet (LF + HF bands combined).
+        (137_000_000, 1_020_000_000)
+    }
+
+    fn supported_sf_bitmap() -> u16 {
+        // SX127x supports SF6–SF12 (no SF5 like the SX126x).
+        0x1FC0
+    }
+
+    fn into_parts(self) -> BoardParts<RadioParts, UartParts, DisplayParts, LedDriver> {
+        let p = self.p;
+
+        mcu::start_timer(p.TIMG0, p.SW_INTERRUPT);
+
+        // AXP192 and SSD1306 share I²C0 (SDA=21, SCL=22). Build the bus
+        // once as blocking, drive the PMIC init, then convert to async for
+        // the display task — avoids re-consuming the I²C0 peripheral.
+        // PMIC failure isn't fatal to boot: log and proceed so the rest of
+        // the firmware can still emit diagnostics.
+        let mut i2c_blocking = I2c::new(p.I2C0, I2cConfig::default())
+            .expect("I2C0 init")
+            .with_sda(p.GPIO21)
+            .with_scl(p.GPIO22);
+        if let Err(_e) = axp::axp192_init_lora_oled(&mut i2c_blocking) {
+            defmt::error!("AXP192 init failed — LoRa rail may be dead");
+        }
+        // Let DCDC1 / LDO2 settle before SPI or display traffic.
+        esp_hal::delay::Delay::new().delay_millis(20);
+
+        // SPI2 for SX1276: SCK=5, MOSI=27, MISO=19
+        let spi_bus = mcu::init_spi(p.SPI2, p.DMA_SPI2, p.GPIO5, p.GPIO27, p.GPIO19);
+
+        // SX1276: CS=18, RESET=23, DIO0=26 (primary IRQ)
+        let radio = esp32::init_radio(spi_bus, p.GPIO18, p.GPIO23, p.GPIO26);
+
+        // UART0 via CP2102 bridge: TX=1, RX=3 (ESP32 default console)
+        use esp_hal::uart::{Config as UartConfig, Uart};
+        let host = UartParts {
+            driver: Uart::new(p.UART0, UartConfig::default())
+                .expect("UART init")
+                .with_tx(p.GPIO1)
+                .with_rx(p.GPIO3)
+                .into_async(),
+        };
+
+        // Hand the (now async) I²C bus to the SSD1306 display task.
+        let display = Some(DisplayParts {
+            i2c: i2c_blocking.into_async(),
+        });
+
+        // TX activity LED on GPIO4 (active HIGH).
+        let led_pin = Output::new(p.GPIO4, Level::Low, OutputConfig::default());
+        let led = SimpleLed(led_pin);
+
+        BoardParts {
+            radio,
+            host,
+            display,
+            led,
+            mac: Self::mac_address(),
+        }
+    }
+}
@@ -0,0 +1,153 @@
+//! LilyGo T-Beam S3 Supreme — ESP32-S3 + SX1262 + SH1106 OLED + AXP2101 PMIC.
+//!
+//! Big-brother of the classic T-Beam: ESP32-S3-WROOM-1 module, SX1262 with a
+//! TCXO, 128×64 SH1106 OLED, AXP2101 PMIC on a dedicated I²C1 bus. Native USB
+//! (no UART bridge chip).
+//!
+//! The AXP2101 gates power to the SX1262 and OLED. Without its init sequence
+//! the LoRa chip never responds on SPI and `LoRa::new` fails.
+//!
+//! Pin map (verified from MeshCore variants/lilygo_tbeam_supreme_SX1262/):
+//!   LoRa SPI: SCK=12, MOSI=11, MISO=13, CS=10
+//!   LoRa ctl: RESET=5, DIO1=1, BUSY=4 (TCXO @ 1.6 V via DIO3)
+//!   OLED I²C: SDA=17, SCL=18, SH1106 @ 0x3C (I²C0)
+//!   PMIC I²C: SDA=42, SCL=41, AXP2101 @ 0x34 (I²C1, blocking, PMIC-only)
+//!   USB:      native USB-C on GPIO19/20 (fixed ESP32-S3 D+/D-)
+//!   LED:      GPIO6 (active HIGH indicator, reuses MeshCore's P_LORA_TX_LED)
+//!
+//! GPS / battery / IMU / SD / BME280 are unused — DongLoRa is a transparent
+//! LoRa-over-USB bridge. The PMIC init only enables ALDO1 (OLED) and ALDO3
+//! (LoRa); other rails are left at their AXP2101 power-on defaults.
+
+use esp_hal::gpio::{Level, Output, OutputConfig};
+use esp_hal::i2c::master::{Config as I2cConfig, I2c};
+use static_cell::StaticCell;
+
+use super::esp32s3;
+use super::traits::{BoardParts, LoRaBoard};
+use crate::driver::axp;
+use crate::driver::sh1106::Sh1106;
+use crate::driver::simple_led::SimpleLed;
+use crate::hal::esp32s3 as mcu;
+
+pub use super::esp32s3::{DisplayI2c, RadioDriver, RadioParts};
+
+// ── Concrete peripheral types ───────────────────────────────────────
+
+pub type DisplayDriver = Sh1106<DisplayI2c>;
+pub type UsbDriver = esp_hal::otg_fs::asynch::Driver<'static>;
+pub type LedDriver = SimpleLed<Output<'static>>;
+
+// ── Peripheral bundles ──────────────────────────────────────────────
+
+pub struct UsbParts {
+    pub driver: UsbDriver,
+}
+
+pub struct DisplayParts {
+    pub i2c: DisplayI2c,
+}
+
+// ── Display init ────────────────────────────────────────────────────
+
+pub async fn create_display(i2c: DisplayI2c) -> Option<DisplayDriver> {
+    let mut display = Sh1106::new(i2c, 0x3C);
+
+    embassy_time::Timer::after_millis(100).await;
+    if display.init().await.is_err() {
+        defmt::error!("SH1106 display init failed");
+        return None;
+    }
+    let _ = display.set_brightness(0xFF).await;
+    Some(display)
+}
+
+// ── Board init ──────────────────────────────────────────────────────
+
+pub struct Board {
+    p: esp_hal::peripherals::Peripherals,
+}
+
+impl LoRaBoard for Board {
+    const NAME: &'static str = "LilyGo T-Beam S3 Supreme";
+    const TX_POWER_RANGE: (i8, i8) = (-9, 22);
+
+    type RadioParts = RadioParts;
+    type CommParts = UsbParts;
+    type DisplayParts = DisplayParts;
+    type DisplayDriver = DisplayDriver;
+    type LedDriver = LedDriver;
+
+    fn init() -> Self {
+        let p = esp_hal::init(esp_hal::Config::default());
+        Self { p }
+    }
+
+    fn mac_address() -> [u8; 6] {
+        mcu::mac_address()
+    }
+
+    fn into_parts(self) -> BoardParts<RadioParts, UsbParts, DisplayParts, LedDriver> {
+        let p = self.p;
+
+        mcu::start_timer(p.TIMG0, p.SW_INTERRUPT);
+
+        // AXP2101 PMIC on I²C1 (SDA=42, SCL=41). Blocking, one-shot: we only
+        // need to flip the LoRa/OLED rails on, then the bus can be dropped.
+        // If this fails the LoRa chip stays unpowered — log and keep going so
+        // the rest of the boot path can still produce diagnostics.
+        {
+            let mut pmic = I2c::new(p.I2C1, I2cConfig::default())
+                .expect("I2C1 init")
+                .with_sda(p.GPIO42)
+                .with_scl(p.GPIO41);
+            if let Err(_e) = axp::axp2101_init_lora_oled(&mut pmic) {
+                defmt::error!("AXP2101 init failed — LoRa rail may be dead");
+            }
+        }
+        // Let ALDO1/ALDO3 settle before touching the LoRa SPI or OLED I²C.
+        esp_hal::delay::Delay::new().delay_millis(20);
+
+        // SPI2 for SX1262: SCK=12, MOSI=11, MISO=13
+        let spi_bus = mcu::init_spi(p.SPI2, p.DMA_CH0, p.GPIO12, p.GPIO11, p.GPIO13);
+
+        // SX1262: CS=10, RESET=5, DIO1=1, BUSY=4, TCXO @ 1.6 V via DIO3.
+        let radio = esp32s3::init_radio(
+            spi_bus,
+            p.GPIO10,
+            p.GPIO5,
+            p.GPIO1,
+            p.GPIO4,
+            lora_phy::sx126x::TcxoCtrlVoltage::Ctrl1V6,
+        );
+
+        // Native USB-C on GPIO19/20. Switches the internal USB PHY from
+        // Serial-JTAG to OTG.
+        let usb_inst = esp_hal::otg_fs::Usb::new(p.USB0, p.GPIO20, p.GPIO19);
+        static EP_OUT_BUF: StaticCell<[u8; 1024]> = StaticCell::new();
+        let ep_out_buf = EP_OUT_BUF.init([0u8; 1024]);
+        let host = UsbParts {
+            driver: esp_hal::otg_fs::asynch::Driver::new(
+                usb_inst,
+                ep_out_buf,
+                esp_hal::otg_fs::asynch::Config::default(),
+            ),
+        };
+
+        // I2C0 for SH1106 OLED: SDA=17, SCL=18 (async, handed to display task).
+        let i2c = mcu::init_i2c(p.I2C0, p.GPIO17, p.GPIO18);
+        let display = Some(DisplayParts { i2c });
+
+        // Activity LED on GPIO6 (active HIGH).
+        let led_pin = Output::new(p.GPIO6, Level::Low, OutputConfig::default());
+        let led = SimpleLed(led_pin);
+
+        BoardParts {
+            radio,
+            host,
+            display,
+            led,
+            mac: Self::mac_address(),
+        }
+    }
+}
@@ -3,7 +3,11 @@ pub mod traits;
 pub use traits::*;

 {% for helper, helper_features in helpers|items -%}
+{% if helper_features|length == 1 -%}
+#[cfg(feature = "{{ helper_features[0] }}")]
+{% else -%}
 #[cfg(any({% for f in helper_features %}feature = "{{ f }}"{% if not loop.last %}, {% endif %}{% endfor %}))]
+{% endif -%}
 mod {{ helper }};
 {% endfor %}
 cfg_if::cfg_if! {
@@ -9,6 +9,8 @@
 use embedded_graphics::draw_target::DrawTarget;
 use embedded_graphics::pixelcolor::BinaryColor;

+use crate::driver::DisplayBrightness;
+
 /// Async RGB LED control. Boards without an LED use `()` which is a no-op.
 pub trait RgbLed {
    fn set_rgb(&mut self, r: u8, g: u8, b: u8) -> impl core::future::Future<Output = ()>;
@@ -35,8 +37,9 @@ pub trait LoRaBoard: Sized {
    /// Display peripheral bundle (I2C bus for display init).
    type DisplayParts;

-    /// Concrete display driver type (must implement DrawTarget for rendering).
-    type DisplayDriver: DrawTarget<Color = BinaryColor>;
+    /// Concrete display driver type (must implement DrawTarget for rendering
+    /// and DisplayBrightness for the two-level dim control).
+    type DisplayDriver: DrawTarget<Color = BinaryColor> + DisplayBrightness;

    /// RGB LED driver. Boards without an LED use `()`.
    type LedDriver: RgbLed;
@@ -47,6 +50,36 @@ pub trait LoRaBoard: Sized {
    /// Read the board's unique hardware address (MAC, device ID, etc.).
    fn mac_address() -> [u8; 6];

+    /// Radio chip identifier reported in `GET_INFO`. Defaults to SX1262
+    /// (`0x0002`), matching every currently-supported board. Override for
+    /// boards that carry a different chip (LLCC68, SX1261, LR11xx, …).
+    fn radio_chip_id() -> u16 {
+        // SX1262 — see PROTOCOL.md §8.
+        0x0002
+    }
+
+    /// (freq_min_hz, freq_max_hz) — the RF front-end's effective tuning
+    /// window on this specific board. Reported in `GET_INFO`. Defaults
+    /// to the SX1262's nominal 150–960 MHz range.
+    fn freq_range_hz() -> (u32, u32) {
+        (150_000_000, 960_000_000)
+    }
+
+    /// Bitmap of supported LoRa spreading factors — bit N = SF N. Defaults
+    /// to SX126x's SF5–SF12 (`0x1FE0`). SX127x boards must override to
+    /// `0x1FC0` (SF6–SF12); LLCC68 boards to `0x0FE0` (SF5–SF11).
+    fn supported_sf_bitmap() -> u16 {
+        0x1FE0
+    }
+
+    /// Bitmap of supported LoRa bandwidths. Bit positions match
+    /// `LoRaBandwidth::as_u8()` (sub-GHz BW enum values 0..9). Defaults
+    /// to all sub-GHz BWs (`0x03FF`). SX128x boards flip the 2.4 GHz
+    /// bits when we add them.
+    fn supported_bw_bitmap() -> u16 {
+        0x03FF
+    }
+
    /// Decompose initialized board into peripheral bundles for each task.
    fn into_parts(
        self,
@@ -1,54 +1,84 @@
-//! Inter-task communication channels.
+//! Inter-task communication channels for DongLoRa Protocol v2.
 //!
-//! - [`CommandChannel`]: USB → Radio (host commands)
-//! - [`ResponseChannel`]: Radio → USB (firmware responses)
-//! - [`DisplayCommandChannel`]: USB → Display (on/off/reset)
-//! - [`RadioEventChannel`]: Radio → Display (typed events from the radio)
+//! - [`CommandChannel`]: host_task → radio_task (tag-correlated commands)
+//! - [`OutboundChannel`]: radio_task → host_task (tag-correlated OK/ERR/TX_DONE
+//!   and tag-0 async RX/ERR events in one queue)
+//! - [`DisplayCommandChannel`]: host_task → display_task (internal only —
+//!   `On` on connect, `Reset` on disconnect; no longer driven from the wire)
+//! - [`RadioEventChannel`]: radio_task → display_task (typed mode/packet events)

 use embassy_sync::blocking_mutex::raw::CriticalSectionRawMutex;
 use embassy_sync::channel::Channel;

-use crate::protocol::{Command, RadioConfig, Response};
+use crate::protocol::{Command, DeviceMessage, LoRaConfig};

-/// Display commands routed from host_task to display_task.
-#[derive(Debug, Clone, Copy, defmt::Format)]
-pub enum DisplayCommand {
-    On,
-    Off,
-    #[allow(dead_code)] // only used by USB host task, not UART
+// ── Host → Radio: tag-correlated commands ───────────────────────────
+
+/// An event flowing from the host task into the radio task.
+///
+/// `Command` carries a non-zero correlation tag (the host framing layer
+/// rejects tag=0 before it reaches here). `Reset` is a lifecycle signal
+/// from the host transport layer (DTR drop, UART teardown, or spec §3.4
+/// inactivity timeout) telling the radio to park back to Unconfigured
+/// and drain queues silently.
+#[allow(clippy::large_enum_variant)]
+#[derive(Debug, Clone)]
+pub enum InboundEvent {
+    Command { tag: u16, cmd: Command },
    Reset,
 }

-/// USB-to-display command channel (depth 4: display commands are rare events).
-pub type DisplayCommandChannel = Channel<CriticalSectionRawMutex, DisplayCommand, 4>;
+/// Host-to-radio event channel (depth 8).
+pub type CommandChannel = Channel<CriticalSectionRawMutex, InboundEvent, 8>;

-/// Host-to-radio command channel (depth 16: buffer bursty host command sequences).
-pub type CommandChannel = Channel<CriticalSectionRawMutex, Command, 16>;
+// ── Radio → Host: OK / ERR / TX_DONE / RX / async ERR ──────────────

-/// Radio-to-host response channel (depth 32: buffer RX packets while USB writes).
-pub type ResponseChannel = Channel<CriticalSectionRawMutex, Response, 32>;
+/// One outbound D→H frame carrying its tag. Tag-correlated messages
+/// (OK, ERR in response, TX_DONE) carry the originating command's tag;
+/// async events (RX, async ERR) carry `tag = 0x0000`.
+#[derive(Debug, Clone)]
+pub struct OutboundFrame {
+    pub tag: u16,
+    pub msg: DeviceMessage,
+}

-/// Radio → downstream typed events. The radio task emits one of these at
-/// every mode transition and every RF packet. Mode events and data events
-/// are separate: `EnteredRx` / `EnteredTx` / `Idle` describe what the radio
-/// is *doing now*, while `PacketRx` / `PacketTx` describe *what just
-/// happened* without implying a mode change.
+/// Radio-to-host outbound channel (depth 32: enough to hold a burst of
+/// RX events + queued command responses without stalling the radio ISR).
+pub type OutboundChannel = Channel<CriticalSectionRawMutex, OutboundFrame, 32>;
+
+// ── Internal: display commands (no longer wire-visible) ────────────
+
+/// Internal display command routed from host_task to display_task. The
+/// wire protocol no longer carries DisplayOn/Off (`PROTOCOL.md §15.2`);
+/// these values drive the display statechart from local events only.
+#[derive(Debug, Clone, Copy, defmt::Format)]
+#[allow(dead_code)] // `Off` is reserved for future diagnostic paths.
+pub enum DisplayCommand {
+    /// Host connected (DTR rose on USB, or UART came up). Wake display.
+    On,
+    /// Host disconnected. Park display.
+    Off,
+    /// Reset cumulative counters (e.g., on config change).
+    Reset,
+}
+
+/// Host-to-display command channel.
+pub type DisplayCommandChannel = Channel<CriticalSectionRawMutex, DisplayCommand, 4>;
+
+// ── Radio → Display: typed packet/mode events ──────────────────────
+
+/// Radio → downstream typed events. These drive the display; they are
+/// NOT the same thing as `OutboundFrame` (which goes out the host
+/// transport). Mode events describe what the radio is doing now; packet
+/// events describe what just happened.
 #[derive(Debug, Clone, defmt::Format)]
 pub enum RadioEvent {
-    /// Radio is now in RX mode.
    EnteredRx,
-    /// Radio is now in TX mode.
    EnteredTx,
-    /// Radio is now idle.
    Idle,
-    /// A packet was received with these link metrics.
    PacketRx { rssi: i16, snr: Option<i16> },
-    /// A packet was transmitted successfully.
    PacketTx,
-    /// `SetConfig` applied a new validated config.
-    ConfigChanged(RadioConfig),
+    ConfigChanged(LoRaConfig),
 }

-/// Radio → Display event stream (depth 32: buffer RX bursts while the
-/// display drains slowly).
 pub type RadioEventChannel = Channel<CriticalSectionRawMutex, RadioEvent, 32>;
@@ -37,8 +37,9 @@ use embassy_time::Timer;
 use hsmc::statechart;

 use crate::board::{self, Board, DisplayDriver, DisplayParts, LedDriver, LoRaBoard, RgbLed};
+use crate::driver::DisplayBrightness;
 use crate::channel::{DisplayCommand, DisplayCommandChannel, RadioEvent, RadioEventChannel};
-use crate::protocol::RadioConfig;
+use crate::protocol::LoRaConfig;

 use render::{BoardInfo, RSSI_HISTORY_LEN};

@@ -75,7 +76,7 @@ pub enum DisplayEvent {
    },
    /// A packet was transmitted (data only — does not imply a mode change).
    PacketTx,
-    ConfigChanged(RadioConfig),
+    ConfigChanged(LoRaConfig),
 }

 impl From<RadioEvent> for DisplayEvent {
@@ -109,7 +110,7 @@ struct RunState {
    rssi_count: usize,
    current_slot_rssi: i16,
    current_slot_tx: bool,
-    config: Option<RadioConfig>,
+    config: Option<LoRaConfig>,
    rx_count: u32,
    tx_count: u32,
    last_rssi: Option<i16>,
@@ -220,6 +221,14 @@ impl DisplayContext {
        Timer::after_millis(50).await;
        self.peripherals.led.set_rgb(0, 0, 0).await;
    }
+
+    async fn oled_bright(&mut self) {
+        self.peripherals.display.set_bright().await;
+    }
+
+    async fn oled_dim(&mut self) {
+        self.peripherals.display.set_dim().await;
+    }
 }

 // ── Statechart ─────────────────────────────────────────────────────
@@ -243,16 +252,26 @@ statechart! {
            on(CmdOff) => Off;
            // `CmdReset` + `RadioIdle` race on USB disconnect; this handler
            // makes either ordering land in the same place. Reset the run
-            // state, turn off any blink-in-progress, and re-enter Splash —
-            // descend_defaults lands us in LearnMore with a fresh 5 s timer.
-            on(CmdReset) => reset_run_state, turn_led_off, Splash;
+            // state, turn off any blink-in-progress, and land in LearnMore
+            // with a fresh 5 s timer. We target `LearnMore` (not `Splash`)
+            // because under hsmc 0.2 up-transition semantics, targeting a
+            // state that's already on the active path would only unwind
+            // below it — we'd park at `Splash` with no active child and
+            // the alternation timer would never restart.
+            on(CmdReset) => reset_run_state, turn_led_off, LearnMore;
            // Config can arrive before the dashboard is up; cache it anywhere.
-            on(ConfigChanged(cfg: RadioConfig)) => save_new_config;
+            on(ConfigChanged(cfg: LoRaConfig)) => save_new_config;

+            // Splash is bright for the first 10 s of (re-)entry, then the
+            // action-only `on(after 10s)` handler drops the OLED to dim.
+            // LearnMore ↔ Info keep alternating underneath — their own
+            // timers are independent of the 10 s window.
            state Splash {
+                entry: set_bright;
                default(LearnMore);
                on(EnteredRx) => Listening;
                on(EnteredTx) => Transmitting;
+                on(after Duration::from_secs(10)) => set_dim;

                state LearnMore {
                    entry: paint_learn_more;
@@ -265,24 +284,56 @@ statechart! {
                }
            }

+            // Dashboard brightness pattern: each mode-leaf holds a `Bright`
+            // substate. `entry: set_bright` owns the backlight going on;
+            // `set_dim` is fired **as an action** by the 3 s timeout
+            // handler, immediately before the up-transition that parks
+            // the machine at the leaf. The symmetric `exit: set_dim`
+            // would also fire on mode-change leaf-crossings (e.g.
+            // ListeningBright → TransmittingBright via EnteredTx), and
+            // the subsequent default descent would fire `set_bright`
+            // again — producing a visible dim/bright flash on every
+            // TX↔RX swap. Anchoring dim to the *timer* handler instead
+            // means leaf-crossings go bright→bright with no intermediate
+            // dim action. CmdOff/CmdReset exit paths don't fire set_dim
+            // either, which is fine — the display is blanked or walked
+            // back to Splash, which re-asserts its own brightness.
            state Dashboard {
                default(Listening);
                on(RadioIdle) => Splash;

-                // Packet events are pure data + one-shot LED feedback.
-                on(PacketRx { rssi: i16, snr: Option<i16> }) => record_rx_packet, blink_rx_led;
-                on(PacketTx) => record_tx_packet, blink_tx_led;
-
                state Listening {
                    entry: paint_listening;
+                    default(ListeningBright);
                    on(EnteredTx) => Transmitting;
                    on(every Duration::from_millis(1000)) => advance_sparkline, paint_listening;
+                    // Split from the transition below because hsmc rejects
+                    // payload bindings on transition-bearing handlers.
+                    on(PacketRx { rssi: i16, snr: Option<i16> }) => record_rx_packet, blink_rx_led;
+                    on(PacketRx) => ListeningBright;
+                    on(PacketTx) => record_tx_packet, blink_tx_led;
+                    on(PacketTx) => ListeningBright;
+
+                    state ListeningBright {
+                        entry: set_bright;
+                        on(after Duration::from_secs(3)) => set_dim, Listening;
+                    }
                }

                state Transmitting {
                    entry: paint_transmitting;
+                    default(TransmittingBright);
                    on(EnteredRx) => Listening;
                    on(every Duration::from_millis(1000)) => advance_sparkline, paint_transmitting;
+                    on(PacketRx { rssi: i16, snr: Option<i16> }) => record_rx_packet, blink_rx_led;
+                    on(PacketRx) => TransmittingBright;
+                    on(PacketTx) => record_tx_packet, blink_tx_led;
+                    on(PacketTx) => TransmittingBright;
+
+                    state TransmittingBright {
+                        entry: set_bright;
+                        on(after Duration::from_secs(3)) => set_dim, Transmitting;
+                    }
                }
            }
        }
@@ -348,13 +399,21 @@ impl DisplayActions for DisplayActionContext<'_> {
        self.led_blip(32, 0, 0).await;
    }

-    async fn save_new_config(&mut self, cfg: RadioConfig) {
+    async fn save_new_config(&mut self, cfg: LoRaConfig) {
        self.run.config = Some(cfg);
    }

    async fn advance_sparkline(&mut self) {
        self.run.advance_slot();
    }
+
+    async fn set_bright(&mut self) {
+        self.oled_bright().await;
+    }
+
+    async fn set_dim(&mut self) {
+        self.oled_dim().await;
+    }
 }

 // ── Task entry point ───────────────────────────────────────────────
@@ -440,7 +499,7 @@ mod render {
    use heapless::String;

    use super::Badge;
-    use crate::protocol::{Bandwidth, RadioConfig};
+    use crate::protocol::{LoRaBandwidth, LoRaConfig};

    pub const RSSI_HISTORY_LEN: usize = 128;

@@ -505,7 +564,7 @@ mod render {
    pub fn dashboard(
        target: &mut impl DrawTarget<Color = BinaryColor>,
        badge: Badge,
-        config: Option<RadioConfig>,
+        config: Option<LoRaConfig>,
        rx_count: u32,
        tx_count: u32,
        last_rssi: Option<i16>,
@@ -588,21 +647,33 @@ mod render {
            let freq_mhz = cfg.freq_hz / 1_000_000;
            let freq_khz = (cfg.freq_hz % 1_000_000) / 1_000;
            let bw_str = match cfg.bw {
-                Bandwidth::Khz7 => "7.8",
-                Bandwidth::Khz10 => "10.4",
-                Bandwidth::Khz15 => "15.6",
-                Bandwidth::Khz20 => "20.8",
-                Bandwidth::Khz31 => "31.2",
-                Bandwidth::Khz41 => "41.7",
-                Bandwidth::Khz62 => "62.5",
-                Bandwidth::Khz125 => "125",
-                Bandwidth::Khz250 => "250",
-                Bandwidth::Khz500 => "500",
+                LoRaBandwidth::Khz7 => "7.8",
+                LoRaBandwidth::Khz10 => "10.4",
+                LoRaBandwidth::Khz15 => "15.6",
+                LoRaBandwidth::Khz20 => "20.8",
+                LoRaBandwidth::Khz31 => "31.2",
+                LoRaBandwidth::Khz41 => "41.7",
+                LoRaBandwidth::Khz62 => "62.5",
+                LoRaBandwidth::Khz125 => "125",
+                LoRaBandwidth::Khz250 => "250",
+                LoRaBandwidth::Khz500 => "500",
+                LoRaBandwidth::Khz200 => "200",
+                LoRaBandwidth::Khz400 => "400",
+                LoRaBandwidth::Khz800 => "800",
+                LoRaBandwidth::Khz1600 => "1600",
+            };
+            // Show only the CR denominator; the "4/" numerator is implied for
+            // every LoRa coding rate and just clutters the line.
+            let cr_str = match cfg.cr {
+                crate::protocol::LoRaCodingRate::Cr4_5 => "5",
+                crate::protocol::LoRaCodingRate::Cr4_6 => "6",
+                crate::protocol::LoRaCodingRate::Cr4_7 => "7",
+                crate::protocol::LoRaCodingRate::Cr4_8 => "8",
            };
            let _ = write!(
                buf,
                "{}.{:03}/{}/{}/{}",
-                freq_mhz, freq_khz, bw_str, cfg.sf, cfg.cr
+                freq_mhz, freq_khz, bw_str, cfg.sf, cr_str
            );
            Text::with_alignment(
                &buf,
@@ -0,0 +1,121 @@
+//! AXP PMIC init — turn on the rails that feed LoRa and the OLED.
+//!
+//! T-Beam–class boards gate LoRa, OLED (and GPS/sensors, which this firmware
+//! does not use) through an X-Powers PMIC on I²C. Until the PMIC is told to
+//! enable the right LDOs/DCDCs, the SX126x/SX127x chip sits unpowered and
+//! `LoRa::new` fails. This module's only job is to flip those switches.
+//!
+//! Two PMICs are covered:
+//!
+//! * [`axp2101_init_lora_oled`] — LilyGo T-Beam S3 Supreme. ALDO3 = 3.3 V
+//!   feeds the SX1262; ALDO1 = 3.3 V feeds the SH1106 OLED. Both live on a
+//!   dedicated I²C1 bus (separate from the display).
+//! * [`axp192_init_lora_oled`] — LilyGo T-Beam (classic). LDO2 = 3.3 V feeds
+//!   the SX1276; DCDC1 = 3.3 V feeds the SSD1306 OLED. PMIC shares the
+//!   display I²C bus.
+//!
+//! Everything unrelated to LoRa + OLED (GPS, sensors, SD, batt ADC) is left
+//! alone. Out-of-scope for a transparent LoRa-over-USB bridge.
+//!
+//! Init is blocking on purpose. It runs once during `into_parts`, which is a
+//! synchronous function called before task spawning. Using the blocking
+//! `embedded_hal` trait keeps the PMIC wiring out of the async machinery and
+//! lets the caller drop the I²C bus immediately after init (no bus handoff).
+
+use embedded_hal::i2c::I2c;
+
+/// Both chips respond at this 7-bit I²C address.
+const PMIC_ADDR: u8 = 0x34;
+
+// ── AXP2101 (T-Beam S3 Supreme) ──────────────────────────────────────
+
+#[cfg(feature = "lilygo_tbeam_supreme")]
+mod axp2101 {
+    use super::{I2c, PMIC_ADDR};
+
+    /// LDO on/off control register. Bits:
+    ///   0 = ALDO1, 1 = ALDO2, 2 = ALDO3, 3 = ALDO4, 4 = BLDO1, 5 = BLDO2.
+    const REG_LDO_ONOFF: u8 = 0x90;
+    /// ALDO1 voltage register (OLED rail on T-Beam Supreme).
+    const REG_ALDO1_V: u8 = 0x92;
+    /// ALDO3 voltage register (LoRa rail on T-Beam Supreme).
+    const REG_ALDO3_V: u8 = 0x94;
+
+    /// Voltage code for 3.3 V on ALDOx: 0.5 V + 28 × 100 mV.
+    const V_3V3: u8 = 28;
+
+    /// Mask enabling ALDO1 + ALDO3 in [`REG_LDO_ONOFF`].
+    const ALDO1_ALDO3: u8 = 0b0000_0101;
+
+    /// Bring up LoRa (ALDO3) and OLED (ALDO1) rails at 3.3 V.
+    ///
+    /// Voltage registers are set before the enable bits to avoid glitching
+    /// the rails through the reset-default voltage. Other rails are left
+    /// untouched (read-modify-write on the enable register) so any
+    /// board-specific OTP defaults stay intact.
+    pub fn init_lora_oled<I: I2c>(i2c: &mut I) -> Result<(), I::Error> {
+        i2c.write(PMIC_ADDR, &[REG_ALDO3_V, V_3V3])?;
+        i2c.write(PMIC_ADDR, &[REG_ALDO1_V, V_3V3])?;
+
+        let mut onoff = [0u8; 1];
+        i2c.write_read(PMIC_ADDR, &[REG_LDO_ONOFF], &mut onoff)?;
+        i2c.write(PMIC_ADDR, &[REG_LDO_ONOFF, onoff[0] | ALDO1_ALDO3])?;
+
+        Ok(())
+    }
+}
+
+#[cfg(feature = "lilygo_tbeam_supreme")]
+pub use axp2101::init_lora_oled as axp2101_init_lora_oled;
+
+// ── AXP192 (T-Beam classic) ──────────────────────────────────────────
+
+#[cfg(feature = "lilygo_tbeam")]
+mod axp192 {
+    use super::{I2c, PMIC_ADDR};
+
+    /// DCDC/LDO enable register. Bit layout:
+    ///   0 = DCDC1, 1 = DCDC3, 2 = LDO2, 3 = LDO3, 4 = DCDC2, 6 = EXTEN.
+    const REG_ONOFF: u8 = 0x12;
+    /// DCDC1 output voltage register (OLED rail on T-Beam classic).
+    /// 7-bit code, 25 mV step, 0.7 V offset → 3.3 V = 104 = `0x68`.
+    const REG_DCDC1_V: u8 = 0x26;
+    /// LDO2/LDO3 voltage register. Upper nibble = LDO2 (LoRa), lower nibble
+    /// = LDO3 (GPS). 100 mV step, 1.8 V offset → 3.3 V = 15 = `0xF`.
+    const REG_LDO23_V: u8 = 0x28;
+
+    /// DCDC1 code for 3.3 V.
+    const DCDC1_3V3: u8 = 0x68;
+    /// LDO2 nibble for 3.3 V in the upper half of [`REG_LDO23_V`].
+    const LDO2_3V3_UPPER: u8 = 0xF0;
+
+    /// Mask enabling DCDC1 + LDO2 in [`REG_ONOFF`].
+    const DCDC1_LDO2: u8 = 0b0000_0101;
+
+    /// Bring up LoRa (LDO2) and OLED (DCDC1) rails at 3.3 V on the
+    /// classic T-Beam's AXP192.
+    ///
+    /// GPS (LDO3) and EXTEN are not touched — this firmware has no GPS,
+    /// and any board-default for LDO3 voltage is preserved by
+    /// read-modify-write. Voltage is programmed before the enable bit
+    /// flips so the rail doesn't glitch through its reset default.
+    pub fn init_lora_oled<I: I2c>(i2c: &mut I) -> Result<(), I::Error> {
+        let mut ldo23 = [0u8; 1];
+        i2c.write_read(PMIC_ADDR, &[REG_LDO23_V], &mut ldo23)?;
+        i2c.write(
+            PMIC_ADDR,
+            &[REG_LDO23_V, (ldo23[0] & 0x0F) | LDO2_3V3_UPPER],
+        )?;
+
+        i2c.write(PMIC_ADDR, &[REG_DCDC1_V, DCDC1_3V3])?;
+
+        let mut onoff = [0u8; 1];
+        i2c.write_read(PMIC_ADDR, &[REG_ONOFF], &mut onoff)?;
+        i2c.write(PMIC_ADDR, &[REG_ONOFF, onoff[0] | DCDC1_LDO2])?;
+
+        Ok(())
+    }
+}
+
+#[cfg(feature = "lilygo_tbeam")]
+pub use axp192::init_lora_oled as axp192_init_lora_oled;
@@ -1,12 +1,78 @@
-#[cfg(any(feature = "wio_tracker_l1", feature = "elecrow_thinknode_m2"))]
+#[cfg(any(
+    feature = "wio_tracker_l1",
+    feature = "elecrow_thinknode_m2",
+    feature = "lilygo_tbeam_supreme"
+))]
 pub mod sh1106;

+#[cfg(any(feature = "lilygo_tbeam_supreme", feature = "lilygo_tbeam"))]
+pub mod axp;
+
 #[cfg(any(
    feature = "heltec_v3",
    feature = "heltec_v3_uart",
    feature = "heltec_v4",
    feature = "elecrow_thinknode_m2",
+    feature = "lilygo_tbeam_supreme",
+    feature = "lilygo_tbeam",
    feature = "wio_tracker_l1",
    feature = "waveshare_rp2040_lora"
 ))]
 pub mod simple_led;
+
+// ── Display brightness ────────────────────────────────────────────────
+//
+// The display statechart dims the OLED a few seconds after the last
+// activity. Our two driver families (`ssd1306` crate and our in-tree
+// `sh1106`) expose incompatible brightness APIs, so we wrap them in a
+// single async trait that the state-machine actions can call uniformly.
+
+/// Two-level backlight control used by the display dashboard.
+pub trait DisplayBrightness {
+    fn set_bright(&mut self) -> impl core::future::Future<Output = ()>;
+    fn set_dim(&mut self) -> impl core::future::Future<Output = ()>;
+}
+
+// Contrast values for the two brightness levels, picked to be common across
+// both driver families. `0xFF` is the SSD1306/SH1106 maximum; `0x08` is ~3%
+// of max — visible in a dim room, barely noticeable in daylight. Tune here.
+const CONTRAST_BRIGHT: u8 = 0xFF;
+const CONTRAST_DIM: u8 = 0x08;
+
+impl<DI, SIZE, MODE> DisplayBrightness for ssd1306::Ssd1306Async<DI, SIZE, MODE>
+where
+    DI: display_interface::AsyncWriteOnlyDataCommand,
+    SIZE: ssd1306::size::DisplaySizeAsync,
+{
+    async fn set_bright(&mut self) {
+        // `Brightness::custom(precharge, contrast)`. Matches the shape of
+        // the crate's BRIGHTEST preset (precharge 0x2) at max contrast.
+        let _ = self
+            .set_brightness(ssd1306::prelude::Brightness::custom(0x2, CONTRAST_BRIGHT))
+            .await;
+    }
+    async fn set_dim(&mut self) {
+        // Low precharge pairs with low contrast — same combination the
+        // crate's DIMMEST preset uses.
+        let _ = self
+            .set_brightness(ssd1306::prelude::Brightness::custom(0x1, CONTRAST_DIM))
+            .await;
+    }
+}
+
+#[cfg(any(
+    feature = "wio_tracker_l1",
+    feature = "elecrow_thinknode_m2",
+    feature = "lilygo_tbeam_supreme"
+))]
+impl<I> DisplayBrightness for sh1106::Sh1106<I>
+where
+    I: embedded_hal_async::i2c::I2c,
+{
+    async fn set_bright(&mut self) {
+        let _ = self.set_brightness(CONTRAST_BRIGHT).await;
+    }
+    async fn set_dim(&mut self) {
+        let _ = self.set_brightness(CONTRAST_DIM).await;
+    }
+}
@@ -0,0 +1,80 @@
+//! ESP32 (classic / non-S3) MCU initialization primitives.
+//!
+//! Mirror of `hal::esp32s3` with a single delta: the classic ESP32 uses a
+//! peripheral-bound DMA (`DMA_SPI2`) rather than the S3's channel-addressed
+//! GDMA (`DMA_CH0`). Timer, I²C, and eFuse access are otherwise identical
+//! between the two Xtensa parts in this esp-hal vintage.
+
+use embassy_sync::blocking_mutex::raw::NoopRawMutex;
+use esp_hal::dma::{DmaRxBuf, DmaTxBuf};
+use esp_hal::gpio::interconnect::{PeripheralInput, PeripheralOutput};
+use esp_hal::i2c::master::I2c;
+use esp_hal::spi::master::{Config as SpiConfig, Spi, SpiDmaBus};
+use esp_hal::spi::Mode as SpiMode;
+use esp_hal::time::Rate;
+use esp_hal::timer::timg::TimerGroup;
+use static_cell::StaticCell;
+
+// ── MCU-level types ─────────────────────────────────────────────────
+
+pub type SpiBus = SpiDmaBus<'static, esp_hal::Async>;
+pub type I2cBus = I2c<'static, esp_hal::Async>;
+
+// ── Timer ───────────────────────────────────────────────────────────
+
+/// Start the ESP-RTOS scheduler and Embassy time driver.
+pub fn start_timer(
+    timg0: esp_hal::peripherals::TIMG0<'static>,
+    sw_int: esp_hal::peripherals::SW_INTERRUPT<'static>,
+) {
+    let timg0 = TimerGroup::new(timg0);
+    let sw_ints = esp_hal::interrupt::software::SoftwareInterruptControl::new(sw_int);
+    esp_rtos::start(timg0.timer0, sw_ints.software_interrupt0);
+}
+
+// ── SPI bus ─────────────────────────────────────────────────────────
+
+/// Initialize SPI2 with peripheral-bound DMA and wrap in a shared bus
+/// (`StaticCell` + `Mutex`).
+///
+/// Generic over pin type. The classic ESP32's matrix of GPIO → peripheral
+/// routes lets any GPIO serve as any SPI signal — same as the S3.
+pub fn init_spi(
+    spi2: esp_hal::peripherals::SPI2<'static>,
+    dma_spi2: esp_hal::peripherals::DMA_SPI2<'static>,
+    sck: impl PeripheralOutput<'static>,
+    mosi: impl PeripheralOutput<'static>,
+    miso: impl PeripheralInput<'static>,
+) -> &'static embassy_sync::mutex::Mutex<NoopRawMutex, SpiBus> {
+    let spi = Spi::new(
+        spi2,
+        SpiConfig::default()
+            .with_frequency(Rate::from_mhz(1))
+            .with_mode(SpiMode::_0),
+    )
+    .expect("SPI init")
+    .with_sck(sck)
+    .with_mosi(mosi)
+    .with_miso(miso)
+    .with_dma(dma_spi2);
+
+    let (rx_buf, rx_desc, tx_buf, tx_desc) = esp_hal::dma_buffers!(256);
+    let dma_rx = DmaRxBuf::new(rx_desc, rx_buf).expect("DMA RX buf");
+    let dma_tx = DmaTxBuf::new(tx_desc, tx_buf).expect("DMA TX buf");
+
+    let spi = spi.with_buffers(dma_rx, dma_tx).into_async();
+
+    static SPI_BUS: StaticCell<embassy_sync::mutex::Mutex<NoopRawMutex, SpiBus>> =
+        StaticCell::new();
+    SPI_BUS.init(embassy_sync::mutex::Mutex::new(spi))
+}
+
+// ── MAC address ─────────────────────────────────────────────────────
+
+/// Read the factory-programmed MAC address from eFuse.
+pub fn mac_address() -> [u8; 6] {
+    esp_hal::efuse::base_mac_address()
+        .as_bytes()
+        .try_into()
+        .expect("MAC is 6 bytes")
+}
@@ -7,10 +7,14 @@
    feature = "heltec_v3",
    feature = "heltec_v3_uart",
    feature = "heltec_v4",
-    feature = "elecrow_thinknode_m2"
+    feature = "elecrow_thinknode_m2",
+    feature = "lilygo_tbeam_supreme"
 ))]
 pub mod esp32s3;

+#[cfg(feature = "lilygo_tbeam")]
+pub mod esp32;
+
 #[cfg(any(feature = "rak_wisblock_4631", feature = "wio_tracker_l1"))]
 pub mod nrf52840;

@@ -1,53 +1,121 @@
-//! Shared COBS protocol helpers for USB and UART transports.
+//! Shared framing helpers for USB and UART host transports.
 //!
-//! Both `usb_task` and `uart_task` use these helpers for frame
-//! accumulation, response encoding, and command routing.
+//! Ingress path: raw bytes → `FrameDecoder` → `(type_id, tag, payload)`
+//! → `Command::parse` → forwarded to radio task along with the tag. On
+//! parse failure we echo `ERR(ELENGTH/EPARAM/EMODULATION/EUNKNOWN_CMD)`
+//! with the received tag. On CRC/COBS failure we emit async
+//! `ERR(EFRAME)` with tag `0x0000` (`PROTOCOL.md §2.5`).
 //!
-//! The actual codec lives in `donglora-protocol` so host crates can
-//! reuse it; this module re-exports the codec and owns the
-//! firmware-only [`route_command`] (which touches embassy channels).
+//! Egress path: `OutboundFrame` (tag + DeviceMessage) → `encode_frame`
+//! → bytes ready for transport-level write.

-pub use donglora_protocol::framing::{cobs_encode_response, CobsDecoder, MAX_FRAME};
+use defmt::warn;

-use crate::channel::{CommandChannel, DisplayCommand, DisplayCommandChannel, ResponseChannel};
-use crate::protocol::{Command, ErrorCode, Response};
+use crate::channel::{CommandChannel, InboundEvent, OutboundChannel, OutboundFrame};
+use crate::protocol::{
+    encode_frame, Command, CommandParseError, DeviceMessage, ErrorCode, FrameEncodeError,
+    MAX_PAYLOAD_FIELD, MAX_WIRE_FRAME,
+};

-/// Route a parsed command to the appropriate handler.
+/// Dispatch a frame-level decode into the appropriate downstream queue.
 ///
-/// Display and MAC commands are handled locally (response sent immediately).
-/// All other commands are forwarded to the radio task (response sent later).
-/// Both paths feed the same `ResponseChannel`, so the one-outstanding-command
-/// rule in PROTOCOL.md is required to keep solicited responses ordered.
-pub async fn route_command(
-    cmd: Command,
+/// - `type_id`, `tag`, and `payload` come from `FrameDecoder`.
+/// - Known commands are forwarded to the radio task via `commands`.
+/// - Parse failures produce a synchronous `ERR` with the echoed tag on
+///   `outbound`, so the host sees a concrete answer instead of timing out.
+/// - The caller is responsible for rejecting `tag == 0` before calling
+///   this; the spec says hosts MUST NOT send tag 0, and we classify such
+///   frames as framing errors upstream.
+pub async fn dispatch_frame(
+    type_id: u8,
+    tag: u16,
+    payload: &[u8],
    commands: &CommandChannel,
-    responses: &ResponseChannel,
-    display_commands: &DisplayCommandChannel,
-    has_display: bool,
-    mac: [u8; 6],
+    outbound: &OutboundChannel,
 ) {
-    match cmd {
-        Command::DisplayOn => {
-            if has_display {
-                display_commands.send(DisplayCommand::On).await;
-                responses.send(Response::Ok).await;
-            } else {
-                responses.send(Response::Error(ErrorCode::NoDisplay)).await;
+    if tag == 0 {
+        // Hosts MUST NOT use tag 0 on outbound commands. Treat as
+        // framing error; do not route to radio. (Spec §2.2)
+        emit_async_err(outbound, ErrorCode::EFrame).await;
+        return;
+    }
+    match Command::parse(type_id, payload) {
+        Ok(cmd) => {
+            let envelope = InboundEvent::Command { tag, cmd };
+            if commands.try_send(envelope).is_err() {
+                emit_sync_err(outbound, tag, ErrorCode::EBusy).await;
            }
        }
-        Command::DisplayOff => {
-            if has_display {
-                display_commands.send(DisplayCommand::Off).await;
-                responses.send(Response::Ok).await;
-            } else {
-                responses.send(Response::Error(ErrorCode::NoDisplay)).await;
-            }
-        }
-        Command::GetMac => {
-            responses.send(Response::MacAddress(mac)).await;
-        }
-        other => {
-            commands.send(other).await;
+        Err(e) => {
+            let code = parse_err_to_wire_code(e);
+            emit_sync_err(outbound, tag, code).await;
+        }
+    }
+}
+
+/// Emit an async framing error (tag = 0x0000) per spec §2.5.
+pub async fn emit_async_err(outbound: &OutboundChannel, code: ErrorCode) {
+    let frame = OutboundFrame {
+        tag: 0,
+        msg: DeviceMessage::Err(code),
+    };
+    if outbound.try_send(frame).is_err() {
+        warn!("async ERR dropped: outbound queue full");
+    }
+}
+
+/// Emit a synchronous error response echoing the originating tag.
+async fn emit_sync_err(outbound: &OutboundChannel, tag: u16, code: ErrorCode) {
+    let frame = OutboundFrame {
+        tag,
+        msg: DeviceMessage::Err(code),
+    };
+    if outbound.try_send(frame).is_err() {
+        warn!("sync ERR dropped: outbound queue full");
+    }
+}
+
+fn parse_err_to_wire_code(e: CommandParseError) -> ErrorCode {
+    match e {
+        CommandParseError::UnknownType => ErrorCode::EUnknownCmd,
+        CommandParseError::WrongLength => ErrorCode::ELength,
+        CommandParseError::InvalidField => ErrorCode::EParam,
+        CommandParseError::ReservedBitSet => ErrorCode::EParam,
+        CommandParseError::UnknownModulation => ErrorCode::EModulation,
+    }
+}
+
+/// Encode an outbound frame into a single wire-ready byte buffer.
+///
+/// Returns the number of bytes written to `out`, or `None` on buffer
+/// overflow / encode failure (caller may log and drop).
+pub fn encode_outbound(frame: &OutboundFrame, out: &mut [u8; MAX_WIRE_FRAME]) -> Option<usize> {
+    let mut payload_buf = [0u8; MAX_PAYLOAD_FIELD];
+    let payload_len = match frame.msg.encode_payload(&mut payload_buf) {
+        Ok(n) => n,
+        Err(e) => {
+            warn!("encode_payload failed: {:?}", defmt::Debug2Format(&e));
+            return None;
+        }
+    };
+    match encode_frame(
+        frame.msg.type_id(),
+        frame.tag,
+        &payload_buf[..payload_len],
+        out.as_mut_slice(),
+    ) {
+        Ok(n) => Some(n),
+        Err(FrameEncodeError::BufferTooSmall) => {
+            warn!("encode_frame: output buffer too small");
+            None
+        }
+        Err(FrameEncodeError::PayloadTooLarge) => {
+            warn!("encode_frame: payload exceeds MAX_PAYLOAD_FIELD");
+            None
+        }
+        Err(FrameEncodeError::CobsEncode) => {
+            warn!("encode_frame: COBS encode refused");
+            None
        }
    }
 }
@@ -6,7 +6,11 @@
 pub mod framing;

 cfg_if::cfg_if! {
-    if #[cfg(any(feature = "heltec_v3_uart", feature = "elecrow_thinknode_m2"))] {
+    if #[cfg(any(
+        feature = "heltec_v3_uart",
+        feature = "elecrow_thinknode_m2",
+        feature = "lilygo_tbeam"
+    ))] {
        mod uart;
        pub use uart::host_task;
    } else {
@@ -1,85 +1,141 @@
-//! UART host task: COBS-framed fixed-size LE command/response protocol.
+//! UART host task for DongLoRa Protocol v2.
 //!
-//! Used for boards with USB-UART bridge chips (e.g. CP2102 on Heltec V3).
+//! UART has no DTR line, so we assume a host is always present and
+//! rely entirely on the spec §3.4 inactivity watchdog (1 s of silence
+//! → Disconnected → drop radio to Unconfigured).

 use defmt::warn;
 use embassy_executor::task;
+use embassy_time::{Duration, Instant};
 use embedded_io_async::Write;

-use super::framing::{self, CobsDecoder, MAX_FRAME};
-use crate::channel::{CommandChannel, DisplayCommand, DisplayCommandChannel, ResponseChannel};
+use super::framing::{dispatch_frame, emit_async_err, encode_outbound};
+use crate::channel::{
+    CommandChannel, DisplayCommand, DisplayCommandChannel, InboundEvent, OutboundChannel,
+};
+use crate::protocol::{ErrorCode, FrameDecoder, FrameResult, MAX_PAYLOAD_FIELD, MAX_WIRE_FRAME};
+
+const READ_BUF: usize = 64;
+const INACTIVITY_MS: u64 = 1000;

 #[task]
 pub async fn host_task(
    parts: crate::board::UartParts,
    commands: &'static CommandChannel,
-    responses: &'static ResponseChannel,
+    outbound: &'static OutboundChannel,
    display_commands: &'static DisplayCommandChannel,
    has_display: bool,
-    mac: [u8; 6],
+    _mac: [u8; 6],
 ) {
    let (mut rx, mut tx) = parts.driver.split();

-    // UART has no DTR — assume a host is always present.
+    // UART has no DTR — wake display immediately and assume a host.
    if has_display {
        display_commands.send(DisplayCommand::On).await;
    }

-    let mut read_buf = [0u8; 64];
-    let mut write_buf = [0u8; MAX_FRAME];
-    let mut cobs_encode_buf = [0u8; MAX_FRAME];
-    let mut decoder = CobsDecoder::new();
+    let mut read_buf = [0u8; READ_BUF];
+    let mut write_buf: [u8; MAX_WIRE_FRAME] = [0u8; MAX_WIRE_FRAME];
+    let mut decoder = FrameDecoder::new();
+    let mut last_frame_at = Instant::now();
+    let mut connected = true;

    loop {
-        use embassy_futures::select::{select, Either};
+        use embassy_futures::select::{select3, Either3};

-        match select(
+        match select3(
            embedded_io_async::Read::read(&mut rx, &mut read_buf),
-            responses.receive(),
+            outbound.receive(),
+            embassy_time::Timer::after(Duration::from_millis(100)),
        )
        .await
        {
-            Either::First(result) => {
-                let n = match result {
-                    Ok(0) => continue,
-                    Ok(n) => n,
-                    Err(_) => {
-                        decoder.reset();
-                        embassy_time::Timer::after_millis(100).await;
-                        continue;
+            Either3::First(result) => match result {
+                Ok(0) => continue,
+                Ok(n) => {
+                    last_frame_at = Instant::now();
+                    if !connected {
+                        if has_display {
+                            let _ = display_commands.try_send(DisplayCommand::On);
+                        }
+                        connected = true;
+                    }
+                    dispatch_bytes(&mut decoder, &read_buf[..n], commands, outbound).await;
+                }
+                Err(_) => {
+                    decoder.reset();
+                    embassy_time::Timer::after_millis(100).await;
+                }
+            },
+            Either3::Second(frame) => {
+                if let Some(n) = encode_outbound(&frame, &mut write_buf) {
+                    if tx.write_all(&write_buf[..n]).await.is_err() {
+                        warn!("UART write failed, frame dropped");
                    }
-                };
-
-                let mut cmds = heapless::Vec::<_, 4>::new();
-                decoder.feed(&read_buf[..n], |cmd| {
-                    let _ = cmds.push(cmd);
-                });
-                for cmd in cmds {
-                    framing::route_command(
-                        cmd,
-                        commands,
-                        responses,
-                        display_commands,
-                        has_display,
-                        mac,
-                    )
-                    .await;
                }
            }
-            Either::Second(response) => {
-                #[cfg(feature = "debug-checkpoint")]
-                crate::debug_blink::set(13);
-                if let Some(frame) =
-                    framing::cobs_encode_response(response, &mut write_buf, &mut cobs_encode_buf)
-                {
-                    if tx.write_all(frame).await.is_err() {
-                        warn!("UART write failed, response dropped");
-                    } else {
-                        #[cfg(feature = "debug-checkpoint")]
-                        crate::debug_blink::set(14);
-                    }
-                }
+            Either3::Third(()) => {}
+        }
+
+        // Inactivity watchdog.
+        if connected && last_frame_at.elapsed() >= Duration::from_millis(INACTIVITY_MS) {
+            warn!("UART host inactivity timeout fired");
+            let _ = commands.try_send(InboundEvent::Reset);
+            if has_display {
+                let _ = display_commands.try_send(DisplayCommand::Reset);
+            }
+            connected = false;
+        }
+    }
+}
+
+async fn dispatch_bytes(
+    decoder: &mut FrameDecoder,
+    bytes: &[u8],
+    commands: &'static CommandChannel,
+    outbound: &'static OutboundChannel,
+) {
+    let mut work: heapless::Vec<FrameWork, 4> = heapless::Vec::new();
+    decoder.feed(bytes, |res| match res {
+        FrameResult::Ok {
+            type_id,
+            tag,
+            payload,
+        } => {
+            let mut p: heapless::Vec<u8, MAX_PAYLOAD_FIELD> = heapless::Vec::new();
+            let _ = p.extend_from_slice(payload);
+            let _ = work.push(FrameWork::Ok {
+                type_id,
+                tag,
+                payload: p,
+            });
+        }
+        FrameResult::Err(_) => {
+            let _ = work.push(FrameWork::Frame);
+        }
+    });
+    for w in work {
+        match w {
+            FrameWork::Ok {
+                type_id,
+                tag,
+                payload,
+            } => {
+                dispatch_frame(type_id, tag, &payload, commands, outbound).await;
+            }
+            FrameWork::Frame => {
+                emit_async_err(outbound, ErrorCode::EFrame).await;
            }
        }
    }
 }
+
+#[allow(clippy::large_enum_variant)]
+enum FrameWork {
+    Ok {
+        type_id: u8,
+        tag: u16,
+        payload: heapless::Vec<u8, MAX_PAYLOAD_FIELD>,
+    },
+    Frame,
+}
@@ -1,54 +1,53 @@
-//! USB CDC-ACM host task: COBS-framed fixed-size LE command/response protocol.
+//! USB CDC-ACM host task for DongLoRa Protocol v2.
 //!
 //! ```text
 //! Host
-//! ├── Disconnected   (default)   no DTR
-//! └── Connected                  host attached
-//!     entry: wake_display
-//!     exit:  stop_radio, reset_display
+//! ├── Disconnected   (default)   no DTR, or inactivity timer fired
+//! └── Connected                  host attached, liveness OK
+//!     entry: wake_display, start_liveness_timer
+//!     exit:  reset_radio, reset_display, stop_liveness_timer
 //! ```
 //!
-//! The statechart tracks exactly one thing: DTR. Entry/exit actions
-//! replace the old `was_connected` edge-detector and emit the display
-//! wake / radio-stop / display-reset side-effects that used to be open
-//! coded around the `select3` loop.
+//! The statechart tracks one state bit: "is a host present?". DTR drives
+//! connect edges; the 1-second inactivity watchdog (spec §3.4) drives
+//! the disconnect edge when DTR is held high but no bytes arrive.
 //!
-//! The data plane (COBS decoding, command routing, response encoding)
-//! stays imperative in `protocol_loop` for the same reason the radio's
-//! `rx_once` stayed out of its chart: `read_packet` blocks and can't
-//! live inside a statechart action. Host-contract lifecycle (one
-//! outstanding command, unsolicited `RxPacket`, synchronous local
-//! responses) is deliberately *not* modeled — any finer chart here
-//! would desynchronise from the concurrent `select3` reality and lie
-//! about what the firmware is actually doing.
+//! The data plane (frame decode, command dispatch, frame encode) stays
+//! imperative in `protocol_loop` for the same reason the radio's
+//! `rx_once` stayed out of its chart: `read_packet` blocks.

 use defmt::warn;
 use embassy_executor::task;
 use embassy_futures::join::join;
+use embassy_time::{Duration, Instant};
 use embassy_usb::class::cdc_acm::{CdcAcmClass, Receiver, Sender, State};
 use embassy_usb::Builder;
-use hsmc::{statechart, Duration};
+use hsmc::{statechart, Duration as HsmcDuration};
 use static_cell::StaticCell;

-use super::framing::{self, CobsDecoder, MAX_FRAME};
-use crate::channel::{CommandChannel, DisplayCommand, DisplayCommandChannel, ResponseChannel};
-use crate::protocol::Command;
+use super::framing::{dispatch_frame, emit_async_err, encode_outbound};
+use crate::channel::{
+    CommandChannel, DisplayCommand, DisplayCommandChannel, InboundEvent, OutboundChannel,
+};
+use crate::protocol::{ErrorCode, FrameDecoder, FrameResult, MAX_WIRE_FRAME};

-const MAX_PACKET: usize = 64;
+const MAX_USB_PACKET: usize = 64;
+
+/// Spec §3.4: inactivity timer period. The device must see at least one
+/// frame (good or bad) every 1000 ms or the session is considered lost.
+const INACTIVITY_MS: u64 = 1000;
+
+/// Poll interval for the DTR edge detector / inactivity check.
+const POLL_INTERVAL_MS: u64 = 100;

-/// Internal events driving `Host` state transitions.
 #[derive(Debug, Clone)]
 pub enum HostInput {
-    /// DTR rose: host opened the serial port.
    DtrRaised,
-    /// DTR fell: host closed or disconnected.
    DtrDropped,
+    /// Host went silent for >1 s; kick the radio back to Unconfigured.
+    InactivityTimeout,
 }

-/// Machine context — channel handles the actions need to broadcast
-/// DTR-edge side-effects. The COBS decoder, read/write scratch, and
-/// USB endpoints stay local to `protocol_loop` because their async
-/// operations can't live inside statechart actions.
 pub struct HostContext {
    commands: &'static CommandChannel,
    display_commands: &'static DisplayCommandChannel,
@@ -68,9 +67,9 @@ impl HostContext {
        }
    }

-    fn stop_radio_best_effort(&self) {
-        if self.commands.try_send(Command::StopRx).is_err() {
-            warn!("host DTR-drop: StopRx dropped (command channel full)");
+    fn send_radio_reset(&self) {
+        if self.commands.try_send(InboundEvent::Reset).is_err() {
+            warn!("radio Reset inject: command queue full");
        }
    }
 }
@@ -87,8 +86,9 @@ statechart! {

        state Connected {
            entry: wake_display;
-            exit: stop_radio, reset_display;
+            exit: reset_radio, reset_display;
            on(DtrDropped) => Disconnected;
+            on(InactivityTimeout) => Disconnected;
        }
    }
 }
@@ -98,8 +98,8 @@ impl HostActions for HostActionContext<'_> {
        self.wake_display_if_present().await;
    }

-    async fn stop_radio(&mut self) {
-        self.stop_radio_best_effort();
+    async fn reset_radio(&mut self) {
+        self.send_radio_reset();
    }

    async fn reset_display(&mut self) {
@@ -111,7 +111,7 @@ impl HostActions for HostActionContext<'_> {
 pub async fn host_task(
    parts: crate::board::UsbParts,
    commands: &'static CommandChannel,
-    responses: &'static ResponseChannel,
+    outbound: &'static OutboundChannel,
    display_commands: &'static DisplayCommandChannel,
    has_display: bool,
    mac: [u8; 6],
@@ -147,7 +147,7 @@ pub async fn host_task(

    let mut builder = Builder::new(parts.driver, config, desc_buf, conf_buf, bos_buf, ctrl_buf);

-    let class = CdcAcmClass::new(&mut builder, cdc_state, MAX_PACKET as u16);
+    let class = CdcAcmClass::new(&mut builder, cdc_state, MAX_USB_PACKET as u16);
    let mut usb_dev = builder.build();
    let (sender, receiver) = class.split();

@@ -157,10 +157,9 @@ pub async fn host_task(
            sender,
            receiver,
            commands,
-            responses,
+            outbound,
            display_commands,
            has_display,
-            mac,
        ),
    )
    .await;
@@ -170,10 +169,9 @@ async fn protocol_loop<'d, D: embassy_usb_driver::Driver<'d>>(
    mut sender: Sender<'d, D>,
    mut receiver: Receiver<'d, D>,
    commands: &'static CommandChannel,
-    responses: &'static ResponseChannel,
+    outbound: &'static OutboundChannel,
    display_commands: &'static DisplayCommandChannel,
    has_display: bool,
-    mac: [u8; 6],
 ) {
    use embassy_futures::select::{select3, Either3};

@@ -182,55 +180,36 @@ async fn protocol_loop<'d, D: embassy_usb_driver::Driver<'d>>(
        display_commands,
        has_display,
    });
-    // Enter the default: Disconnected.
-    machine.step(Duration::ZERO).await;
+    machine.step(HsmcDuration::ZERO).await;

-    let mut read_buf = [0u8; MAX_PACKET];
-    let mut write_buf = [0u8; MAX_FRAME];
-    let mut cobs_encode_buf = [0u8; MAX_FRAME];
-    let mut decoder = CobsDecoder::new();
+    let mut read_buf = [0u8; MAX_USB_PACKET];
+    let mut write_buf: [u8; MAX_WIRE_FRAME] = [0u8; MAX_WIRE_FRAME];
+    let mut decoder = FrameDecoder::new();
+
+    let mut last_frame_at = Instant::now();

    loop {
        match select3(
            receiver.read_packet(&mut read_buf),
-            responses.receive(),
-            embassy_time::Timer::after_millis(250),
+            outbound.receive(),
+            embassy_time::Timer::after(Duration::from_millis(POLL_INTERVAL_MS)),
        )
        .await
        {
            Either3::First(Ok(0)) => {}
            Either3::First(Ok(n)) => {
-                let mut cmds = heapless::Vec::<_, 4>::new();
-                decoder.feed(&read_buf[..n], |cmd| {
-                    let _ = cmds.push(cmd);
-                });
-                for cmd in cmds {
-                    framing::route_command(
-                        cmd,
-                        commands,
-                        responses,
-                        display_commands,
-                        has_display,
-                        mac,
-                    )
-                    .await;
-                }
+                last_frame_at = Instant::now();
+                dispatch_bytes(&mut decoder, &read_buf[..n], commands, outbound).await;
            }
            Either3::First(Err(_)) => {
-                // Read errored — usually a USB disconnect. Drop decoder
-                // scratch and back off briefly so we don't spin at I/O
-                // rate. Do NOT `continue`: the DTR check below must
-                // still run so the machine's exit action fires.
                decoder.reset();
                embassy_time::Timer::after_millis(100).await;
            }
-            Either3::Second(response) => {
-                if let Some(frame) =
-                    framing::cobs_encode_response(response, &mut write_buf, &mut cobs_encode_buf)
-                {
-                    for chunk in frame.chunks(MAX_PACKET) {
+            Either3::Second(frame) => {
+                if let Some(n) = encode_outbound(&frame, &mut write_buf) {
+                    for chunk in write_buf[..n].chunks(MAX_USB_PACKET) {
                        if sender.write_packet(chunk).await.is_err() {
-                            warn!("USB write failed, response dropped");
+                            warn!("USB write failed, frame dropped");
                            break;
                        }
                    }
@@ -239,27 +218,90 @@ async fn protocol_loop<'d, D: embassy_usb_driver::Driver<'d>>(
            Either3::Third(()) => {}
        }

-        // Edge-detect DTR against the machine's current state. The
-        // machine's entry/exit actions own the side-effects. dispatch()
-        // pushes the event AND drains the internal queue, so
-        // current_state() reflects the post-dispatch state before we
-        // loop back around.
+        // DTR edge detection — drives Connected / Disconnected transitions.
        let connected = receiver.dtr();
        let was_connected = matches!(machine.current_state(), HostState::Connected);
        match (was_connected, connected) {
            (false, true) => {
                let _ = machine.dispatch(HostInput::DtrRaised).await;
+                last_frame_at = Instant::now();
            }
            (true, false) => {
-                // Belt-and-braces: reset decoder here too. The error
-                // arm above typically fires on disconnect and already
-                // resets it, but this makes intent explicit and
-                // survives embassy-usb behavior changes where a
-                // disconnect doesn't surface as a read error.
                decoder.reset();
                let _ = machine.dispatch(HostInput::DtrDropped).await;
            }
            _ => {}
        }
+
+        // Inactivity watchdog (spec §3.4): while Connected, if no frame
+        // arrived in the last INACTIVITY_MS, drive the session back to
+        // Disconnected.
+        if matches!(machine.current_state(), HostState::Connected)
+            && last_frame_at.elapsed() >= Duration::from_millis(INACTIVITY_MS)
+        {
+            warn!("host inactivity timeout fired");
+            let _ = machine.dispatch(HostInput::InactivityTimeout).await;
+        }
    }
 }
+
+/// Feed raw bytes into the frame decoder. For each complete frame:
+/// - Ok → route into the command channel (or emit sync ERR on parse fail)
+/// - Err(Crc | Cobs | TooShort) → emit async ERR(EFRAME)
+///
+/// Borrow-scoped per the `FrameDecoder::feed` callback contract: the
+/// payload slice is valid only for the duration of the callback.
+async fn dispatch_bytes(
+    decoder: &mut FrameDecoder,
+    bytes: &[u8],
+    commands: &'static CommandChannel,
+    outbound: &'static OutboundChannel,
+) {
+    // `FrameDecoder::feed` hands payloads by reference; we must synchronously
+    // copy any data we need before the callback returns. To avoid fighting
+    // lifetimes we accumulate per-frame work as an enum.
+    let mut work: heapless::Vec<FrameWork, 4> = heapless::Vec::new();
+    decoder.feed(bytes, |res| match res {
+        FrameResult::Ok {
+            type_id,
+            tag,
+            payload,
+        } => {
+            let mut p: heapless::Vec<u8, { crate::protocol::MAX_PAYLOAD_FIELD }> =
+                heapless::Vec::new();
+            let _ = p.extend_from_slice(payload);
+            let _ = work.push(FrameWork::Ok {
+                type_id,
+                tag,
+                payload: p,
+            });
+        }
+        FrameResult::Err(_e) => {
+            let _ = work.push(FrameWork::Frame);
+        }
+    });
+    for w in work {
+        match w {
+            FrameWork::Ok {
+                type_id,
+                tag,
+                payload,
+            } => {
+                dispatch_frame(type_id, tag, &payload, commands, outbound).await;
+            }
+            FrameWork::Frame => {
+                emit_async_err(outbound, ErrorCode::EFrame).await;
+            }
+        }
+    }
+}
+
+#[allow(clippy::large_enum_variant)]
+enum FrameWork {
+    Ok {
+        type_id: u8,
+        tag: u16,
+        payload: heapless::Vec<u8, { crate::protocol::MAX_PAYLOAD_FIELD }>,
+    },
+    Frame,
+}
@@ -39,14 +39,16 @@ use embassy_executor::Spawner;
 #[cfg(not(test))]
 use crate::board::LoRaBoard;
 #[cfg(not(test))]
-use crate::channel::{CommandChannel, DisplayCommandChannel, RadioEventChannel, ResponseChannel};
+use crate::channel::{CommandChannel, DisplayCommandChannel, OutboundChannel, RadioEventChannel};
+#[cfg(not(test))]
+use crate::protocol::{cap, Info, MAX_MCU_UID_LEN, MAX_RADIO_UID_LEN};

 #[cfg(not(test))]
 cfg_if::cfg_if! {
    if #[cfg(any(feature = "rak_wisblock_4631", feature = "wio_tracker_l1", feature = "waveshare_rp2040_lora"))] {
        use defmt_rtt as _;
        use panic_probe as _;
-    } else if #[cfg(any(feature = "heltec_v3", feature = "heltec_v3_uart", feature = "heltec_v4", feature = "elecrow_thinknode_m2"))] {
+    } else if #[cfg(any(feature = "heltec_v3", feature = "heltec_v3_uart", feature = "heltec_v4", feature = "elecrow_thinknode_m2", feature = "lilygo_tbeam_supreme", feature = "lilygo_tbeam"))] {
        use esp_backtrace as _;
        use esp_println as _;
    }
@@ -55,11 +57,13 @@ cfg_if::cfg_if! {
 #[cfg(not(test))]
 static COMMANDS: CommandChannel = CommandChannel::new();
 #[cfg(not(test))]
-static RESPONSES: ResponseChannel = ResponseChannel::new();
+static OUTBOUND: OutboundChannel = OutboundChannel::new();
 #[cfg(not(test))]
 static RADIO_EVENTS: RadioEventChannel = RadioEventChannel::new();
 #[cfg(not(test))]
 static DISPLAY_COMMANDS: DisplayCommandChannel = DisplayCommandChannel::new();
+#[cfg(not(test))]
+static mut INFO: Option<Info> = None;

 #[cfg(not(test))]
 cfg_if::cfg_if! {
@@ -68,7 +72,7 @@ cfg_if::cfg_if! {
        async fn main(spawner: Spawner) {
            run(spawner).await;
        }
-    } else if #[cfg(any(feature = "heltec_v3", feature = "heltec_v3_uart", feature = "heltec_v4", feature = "elecrow_thinknode_m2"))] {
+    } else if #[cfg(any(feature = "heltec_v3", feature = "heltec_v3_uart", feature = "heltec_v4", feature = "elecrow_thinknode_m2", feature = "lilygo_tbeam_supreme", feature = "lilygo_tbeam"))] {
        #[esp_rtos::main]
        async fn main(spawner: Spawner) {
            run(spawner).await;
@@ -81,8 +85,18 @@ async fn run(spawner: Spawner) {
    let board = <board::Board as LoRaBoard>::init();
    let parts = board.into_parts();

+    // Build the GET_INFO struct once at boot. This is the authoritative
+    // snapshot of device capabilities reported over the wire.
+    let info = build_info(parts.mac);
+    // SAFETY: touched only here at boot, before any task is spawned.
+    let info_ref: &'static Info = unsafe {
+        INFO = Some(info);
+        #[allow(static_mut_refs)]
+        INFO.as_ref().expect("INFO just initialized")
+    };
+
    spawner.spawn(
-        radio::radio_task(parts.radio, &COMMANDS, &RESPONSES, &RADIO_EVENTS)
+        radio::radio_task(parts.radio, &COMMANDS, &OUTBOUND, &RADIO_EVENTS, info_ref)
            .expect("spawn radio_task"),
    );

@@ -90,7 +104,7 @@ async fn run(spawner: Spawner) {
        host::host_task(
            parts.host,
            &COMMANDS,
-            &RESPONSES,
+            &OUTBOUND,
            &DISPLAY_COMMANDS,
            parts.display.is_some(),
            parts.mac,
@@ -98,6 +112,9 @@ async fn run(spawner: Spawner) {
        .expect("spawn host_task"),
    );

+    // Suppress "assigned but never read" warning on non-USB/UART path.
+    let _ = info_ref;
+
    if let Some(dp) = parts.display {
        #[cfg(feature = "debug-checkpoint")]
        {
@@ -117,3 +134,61 @@ async fn run(spawner: Spawner) {
        }
    }
 }
+
+#[cfg(not(test))]
+fn build_info(mac: [u8; 6]) -> Info {
+    let (fmin, fmax) = <board::Board as LoRaBoard>::freq_range_hz();
+    let chip_id = <board::Board as LoRaBoard>::radio_chip_id();
+    let (tx_min, tx_max) = board::Board::TX_POWER_RANGE;
+    let supported_sf = <board::Board as LoRaBoard>::supported_sf_bitmap();
+    let supported_bw = <board::Board as LoRaBoard>::supported_bw_bitmap();
+
+    let mut mcu_uid = [0u8; MAX_MCU_UID_LEN];
+    mcu_uid[..6].copy_from_slice(&mac);
+
+    Info {
+        proto_major: 1,
+        proto_minor: 0,
+        fw_major: parse_u8_or(env!("CARGO_PKG_VERSION_MAJOR"), 0),
+        fw_minor: parse_u8_or(env!("CARGO_PKG_VERSION_MINOR"), 0),
+        fw_patch: parse_u8_or(env!("CARGO_PKG_VERSION_PATCH"), 0),
+        radio_chip_id: chip_id,
+        capability_bitmap: cap::LORA | cap::CAD_BEFORE_TX,
+        supported_sf_bitmap: supported_sf,
+        supported_bw_bitmap: supported_bw,
+        max_payload_bytes: crate::protocol::MAX_OTA_PAYLOAD as u16,
+        // Real channel depths from channel.rs.
+        rx_queue_capacity: 32,
+        tx_queue_capacity: 1,
+        freq_min_hz: fmin,
+        freq_max_hz: fmax,
+        tx_power_min_dbm: tx_min,
+        tx_power_max_dbm: tx_max,
+        mcu_uid_len: 6,
+        mcu_uid,
+        radio_uid_len: 0,
+        radio_uid: [0u8; MAX_RADIO_UID_LEN],
+    }
+}
+
+#[cfg(not(test))]
+const fn parse_u8_or(s: &str, default: u8) -> u8 {
+    // CARGO_PKG_VERSION_* strings are short decimal ascii. Parse them at
+    // compile time via a tiny constant function instead of pulling in a
+    // dependency.
+    let bytes = s.as_bytes();
+    let mut i = 0;
+    let mut out: u32 = 0;
+    while i < bytes.len() {
+        let b = bytes[i];
+        if b < b'0' || b > b'9' {
+            return default;
+        }
+        out = out * 10 + (b - b'0') as u32;
+        if out > u8::MAX as u32 {
+            return default;
+        }
+        i += 1;
+    }
+    out as u8
+}
@@ -1,12 +1,16 @@
-//! Wire protocol types.
+//! Wire protocol types for DongLoRa Protocol v2.
 //!
-//! The definitions live in the `donglora-protocol` crate so host-side
-//! Rust projects (client-rs, mux-rs, bridge) can share them with the
-//! firmware without duplicating wire layouts. This module re-exports
-//! them unchanged for existing `crate::protocol::*` call sites.
+//! Wire definitions live in the `donglora-protocol` crate so host-side
+//! Rust projects can share them with the firmware without duplicating
+//! wire layouts. This module re-exports them unchanged so firmware
+//! modules can `use crate::protocol::*;`.

 #[allow(unused_imports)]
 pub use donglora_protocol::{
-    Bandwidth, Command, ErrorCode, RadioConfig, Response, MAX_PAYLOAD, PREAMBLE_DEFAULT,
-    RADIO_CONFIG_SIZE, TX_POWER_MAX,
+    cap, commands, encode_frame, events, Command, CommandParseError, DeviceMessage,
+    DeviceMessageParseError, ErrorCode, FlrcConfig, FrameDecoder, FrameEncodeError, FrameResult,
+    FskConfig, Info, InfoParseError, LoRaBandwidth, LoRaCodingRate, LoRaConfig, LoRaHeaderMode,
+    LrFhssConfig, Modulation, ModulationId, OkPayload, Owner, RadioChipId, RxOrigin, RxPayload,
+    SetConfigResult, SetConfigResultCode, TxDonePayload, TxFlags, TxResult, MAX_MCU_UID_LEN,
+    MAX_OK_PAYLOAD, MAX_OTA_PAYLOAD, MAX_PAYLOAD_FIELD, MAX_RADIO_UID_LEN, MAX_WIRE_FRAME,
 };
Author	SHA1	Message	Date
swaits	a2c611841b	chore: release 1.3.0	2026-04-23 12:50:03 -06:00
swaits	a1b92356b3	feat(boards): LilyGo T-Beam (classic) support First classic-ESP32 (non-S3) board in the firmware, and first SX127x radio. ESP32 + SX1276 + SSD1306 OLED + AXP192 PMIC, CP2102 USB-UART bridge. Pin map verified from MeshCore variants/lilygo_tbeam_SX1276. The AXP192 gates power to the LoRa chip and OLED. Its I²C bus is shared with the display, so the firmware builds I²C0 in blocking mode first for the PMIC init, then converts the same handle to async and hands it to the display task — avoids double-consuming the peripheral. Lora-phy's Sx127x support drives DIO0 as the sole IRQ (SX127x has no BUSY line); the chip runs from a crystal, tx_boost routes +20 dBm through PA_BOOST. The `esp-hal` / `esp-rtos` / `esp-backtrace` / `esp-println` deps have been restructured so the chip flavour (esp32 vs esp32s3) is selected at the per-board feature level instead of baked into the dep lines. This keeps the existing S3 boards building on esp32s3 while the new T-Beam feature selects classic esp32 via the same dependency set. LoRaBoard gains supported_sf_bitmap() / supported_bw_bitmap() methods (with SX126x defaults) so the T-Beam can report SF6–SF12 via GET_INFO — the SX1276 has no SF5. radio_chip_id() reports 0x0011 per donglora-protocol RadioChipId::Sx1276. freq_range_hz widens to the SX1276 datasheet span of 137 MHz–1020 MHz. New modules: - src/hal/esp32.rs — classic-ESP32 MCU primitives - src/board/esp32.rs — Sx127x radio + SSD1306 display pipe - src/board/lilygo_tbeam.rs — the board file - src/driver/axp.rs — AXP192 init added alongside AXP2101	2026-04-23 10:42:42 -06:00
swaits	7fca5fcb50	feat(boards): LilyGo T-Beam S3 Supreme support ESP32-S3 + SX1262 + SH1106 OLED + AXP2101 PMIC, native USB-C. The AXP2101 PMIC gates power to the LoRa chip and the OLED. Without its init sequence (ALDO3 = 3.3 V for LoRa, ALDO1 = 3.3 V for OLED) the SX1262 never responds on SPI and radio init fails. Pin map verified against MeshCore's variants/lilygo_tbeam_supreme_SX1262. PMIC lives on a dedicated I²C1 bus (SDA=42, SCL=41) separate from the SH1106 on I²C0 (SDA=17, SCL=18); I²C1 is used blocking for a one-shot init and then dropped. TCXO at 1.6 V via DIO3. New src/driver/axp.rs holds the AXP2101 init sequence — kept minimal (only the LoRa + OLED rails), since DongLoRa is a LoRa-over-USB bridge and every other rail (GPS, BME280, IMU, SD, batt ADC) is out of scope.	2026-04-23 10:29:48 -06:00
swaits	6867439044	chore: release 1.2.1	2026-04-22 23:59:44 -06:00
swaits	bcfe736b30	fix(radio): preserve RX session across transient failures Extends the v1.1.0 "SET_CONFIG during RX auto-re-arms" invariant to every failure path that can fire while a client has RX active: * `Receiving.on(RxFailed)` now transitions to `ResumingRx` instead of `Idle`. A transient `next_packet` error re-arms the chip rather than ending the session. * `TransmittingFromRx.on(TransmitFailed)` now transitions to `ResumingRx` instead of `Idle`. TX failure during RX still responds `TX_FAILED` to the caller, then returns to RX — matching the shape of the adjacent `ChannelBusy` handler, which already did this. * `ResumingRx.on(StartRxFailed)` is now a bounded retry (5 attempts, 25 ms backoff) rather than an immediate drop to `Idle`. Only after the retry budget is exhausted does the chip actually land in `Idle`, at which point it's genuinely wedged and needs reconfiguring. Observable effect: the OLED dashboard no longer bounces to Splash when a client (e.g. ai-bot) TXes while bridges are receiving. Previously any single hiccup in the RX/TX/ResumeRX cycle would announce `RadioEvent::Idle`, bouncing the OLED, and the radio would sit in Idle with no client aware enough to re-issue RX_START — stranding the session. The invariant should have held for the whole RX window between `CMD_RX_START` and `CMD_RX_STOP`; now it does. Implementation notes: * Two new internal `RadioInput` variants: `ResumeRxRetry` drives the `ResumingRx` self-transition; `ResumeRxExhausted` breaks out to Idle after too many failed tries. * New `resume_retries: u8` field on `RadioContext`, reset to 0 on every successful `StartRxOk`, bumped by `bump_resume_retries`. * Constants `MAX_RESUME_RETRIES = 5` and `RESUME_RX_RETRY_BACKOFF_MS = 25` at the top of `radio.rs`. * Removed the dead `announce_rx_failed` helper — its only caller was the now-deleted `Receiving.on(RxFailed) => Idle` edge. No behavior change for the three paths where `Idle` remains the correct landing state: initial `CmdRxStart` failure in `StartingRx`, `CmdRxStop` in `Receiving`, and all three `TransmittingFromIdle` outcomes (where RX wasn't running to begin with).	2026-04-22 23:59:12 -06:00
swaits	0033bbb941	chore: release 1.2.0	2026-04-22 20:50:11 -06:00
swaits	42a6b1142d	feat(display): OLED dims a few seconds after last activity Splash holds bright for 10 s on (re-)entry, then drops to dim while LearnMore/Info keep alternating. The dashboard stays bright for 3 s after the last packet or mode change, then dims in place without disturbing the Listening/Transmitting state or the 1 s sparkline timer. Cross-leaf TX↔RX hops stay bright throughout — `set_dim` is fired by the 3 s timer handler as an action rather than as a sibling `exit:` action, so mode-change leaf-crossings no longer flash dim→bright on every swap. Two driver families (`ssd1306::Ssd1306Async` and the in-tree `Sh1106`) wrapped behind a single `DisplayBrightness` trait in `src/driver/mod.rs`; the board trait's `DisplayDriver` associated type now requires it. Dim/bright contrast values centralized as `CONTRAST_BRIGHT` / `CONTRAST_DIM` constants — tune in one place. `On.on(CmdReset)` now targets `LearnMore` directly rather than the ancestor `Splash`. Under hsmc 0.2 up-transition semantics, targeting an already-active ancestor unwinds only below it without re-descent; the USB-disconnect reset path was previously relying on the old re-enter-and-descend behavior and would have parked at `Splash` with a dead alternation timer. Bumps `hsmc` 0.1.0 → 0.2 for the up-transition semantic fix.	2026-04-22 19:38:42 -06:00
swaits	fa1eeceb7c	fix(boards): Elecrow ThinkNode-M2 uses CH340K, not CP2102 The shipping revision of this board has a WCH CH340K USB-UART bridge (1a86:7522), not a Silicon Labs CP2102 as the original board-module comment claimed. Update the doc header, and add the CH340K + CH340-standard VID:PIDs to the `just flash` port list so we stop falling through to espflash auto-detect on these boards.	2026-04-22 19:32:34 -06:00
swaits	027ac5eb04	chore: release 1.1.0	2026-04-22 11:47:42 -06:00
swaits	b7d9b37bb0	feat: auto-resume RX across SET_CONFIG (protocol v1.1 §3.5) Inside state Receiving, override the parent Configured state chart handler on(ConfigApplied) => Idle with on(ConfigApplied) => ResumingRx. ResumingRx entry (try_start_rx_hw) re-enables RX on the chip with the new modulation once apply_set_config has finished the SPI write + calibration, and transitions back to Receiving on StartRxOk. Net effect: SET_CONFIG issued while the radio is in continuous RX no longer kicks the radio (and therefore the OLED) out to idle. The RX ring is still cleared by apply_set_config; callers never need to re-issue RX_START after SET_CONFIG. This matches donglora-protocol 1.1.0 §3.5 and §6.3 normative behavior.	2026-04-22 11:47:14 -06:00
swaits	b0ce0a7aca	chore: release 1.0.0	2026-04-22 09:32:06 -06:00
swaits	2a3c2be060	feat!: migrate firmware to DongLoRa Protocol v2 wire format Wire-incompatible break with the 0.x protocol. Every host-side path (UART, USB CDC, framing, radio dispatcher, display update channel) speaks the v2 wire format defined in PROTOCOL.md. * Replace the host framing path with streaming FrameDecoder + encode_frame from donglora-protocol, matching the new (type_id, tag, payload) shape. * Update src/channel.rs and src/host/{uart,usb,framing}.rs for the new frame semantics: per-request tag echo, CRC checked in the decoder, async ERR fan-out on tag 0. * Rework src/radio.rs to emit RX / TX_DONE / OK / ERR messages in v2 shape, including RxOrigin, TxDonePayload, and SetConfigResult codes. * Update src/protocol.rs glue to re-export v2 types from donglora-protocol and drop the legacy 0.x shim surface. * Refresh PROTOCOL.md to the v2 normative spec (kept in sync with the donglora-protocol crate). * Minor display and main-loop cleanups needed for the new radio event shape.	2026-04-22 09:32:06 -06:00