Rewrites lingering github.com / *.sr.ht references to this Gitea instance,
translating GitHub and Sourcehut URL shapes to Gitea's (/blob/<ref>/ and
sr.ht /tree/<ref>/item/ -> /src/branch/<ref>/, /tree/<tag> -> /src/tag/<tag>,
/actions/workflows/X -> /actions?workflow=X, /edit/ -> /_edit/).
Left pointing at the old hosts on purpose: pull-request links (PRs were not
migrated), forks that were never migrated, and GitHub-only surfaces Gitea
lacks. OpenPGP identity proofs are untouched by design.
Audit conducted at v1.5.2 (commit 688938d). Findings:
- 0 Critical / 0 High / 0 Medium / 2 Low / 1 Info
- Realistic attack surface = host transport + OTA RX; both traced
end-to-end with no exploitable defects found.
Hardening applied as part of audit follow-up:
- esp-println now uses default-features=false; output target is
selected per-board. UART-host boards (heltec_v3_uart,
elecrow_thinknode_m2, lilygo_tbeam classic) get `no-op` so
defmt/panic output cannot corrupt frames on UART0 (the host
protocol wire). Native-USB boards keep `auto` so espflash-monitor
still works.
- README documents the trust model: no host-transport auth, no
RF-regulatory enforcement, MAC exposed via USB iSerialNumber +
GET_INFO.mcu_uid (intentional, needed by donglora-mux for
multi-dongle disambiguation).
Adds nRF52840 + SX1262 + 1.14" 240×135 ST7789 color TFT support. First
color display board in the project; introduces a BoardDisplay trait so
each board renders to its native pixel format and resolution without
aliasing or color-quantization round-trips.
Architecture:
- New BoardDisplay trait (src/display.rs) bundles render_*, present(),
set_bright/set_dim. Replaces the old DrawTarget<Color=BinaryColor>
+ DisplayBrightness combo as the LoRaBoard::DisplayDriver bound.
- Mono OLED drivers (Sh1106, Ssd1306Async) get adapter impls that
delegate to the existing display::render module — no behavior change
for any existing board.
- T114 ST7789 driver (src/driver/st7789.rs) wraps lcd-async (async fork
of mipidsi) with a 64,800-byte raw byte framebuffer in .bss. Renders
via lcd_async::raw_framebuf::RawFrameBuf<Rgb565, _>, presents via a
single async DMA blit (panel.show_raw_data(...).await) — the await
yields the executor for the ~65 ms SPI transfer so the radio task
isn't starved during repaints.
- PWM backlight on PWM0 / P0.15 (active-LOW, inverted polarity) for
smooth dim/bright transitions instead of GPIO toggle.
- Native 240×135 Rgb565 renderer (src/display/render_color.rs) with
splash + dashboard + sparkline.
- Shared QR-code blit (src/display/qr.rs), generic over PixelColor,
re-centers the 64×64 bitmap which has cells in cols 0..50 and ~14 px
of right-side padding — both mono and color splash now show the QR
with 7 px quiet zones on all four sides (was visibly left-shifted).
- Shared content types (BoardInfo, DashboardCtx) decouple what to draw
from how each board renders it.
- create_display() now takes the board's full DisplayParts bundle
(was just the I2C bus) so non-I2C displays can carry SPI + control
pins through.
Hardware:
- VEXT_ENABLE on P0.21 driven HIGH at boot — powers the SX1262 + TFT
rail. Without this, lora-phy init succeeds at the SPI level but
TX_DONE never fires.
- VTFT_CTRL on P0.03, active LOW; backlight on P0.15, active LOW.
- TFT SPI2 (SCK P1.08 / MOSI P1.09) at 8 MHz over EasyDMA. Async
ExclusiveDevice from embedded-hal-bus (with the 'async' feature).
- lcd-async builder at display_size(135, 240), display_offset(52, 40),
Deg90 rotation, ColorInversion::Inverted — standard 1.14" ST7789
die mapping.
- Linker: shared ld/nrf52840-memory.x (S140 SoftDevice preserved at
0x01000-0x26000 per project policy).
First classic-ESP32 (non-S3) board in the firmware, and first SX127x
radio. ESP32 + SX1276 + SSD1306 OLED + AXP192 PMIC, CP2102 USB-UART
bridge. Pin map verified from MeshCore variants/lilygo_tbeam_SX1276.
The AXP192 gates power to the LoRa chip and OLED. Its I²C bus is
shared with the display, so the firmware builds I²C0 in blocking mode
first for the PMIC init, then converts the same handle to async and
hands it to the display task — avoids double-consuming the peripheral.
Lora-phy's Sx127x support drives DIO0 as the sole IRQ (SX127x has no
BUSY line); the chip runs from a crystal, tx_boost routes +20 dBm
through PA_BOOST.
The `esp-hal` / `esp-rtos` / `esp-backtrace` / `esp-println` deps have
been restructured so the chip flavour (esp32 vs esp32s3) is selected
at the per-board feature level instead of baked into the dep lines.
This keeps the existing S3 boards building on esp32s3 while the new
T-Beam feature selects classic esp32 via the same dependency set.
LoRaBoard gains supported_sf_bitmap() / supported_bw_bitmap() methods
(with SX126x defaults) so the T-Beam can report SF6–SF12 via GET_INFO
— the SX1276 has no SF5. radio_chip_id() reports 0x0011 per
donglora-protocol RadioChipId::Sx1276. freq_range_hz widens to the
SX1276 datasheet span of 137 MHz–1020 MHz.
New modules:
- src/hal/esp32.rs — classic-ESP32 MCU primitives
- src/board/esp32.rs — Sx127x radio + SSD1306 display pipe
- src/board/lilygo_tbeam.rs — the board file
- src/driver/axp.rs — AXP192 init added alongside AXP2101
ESP32-S3 + SX1262 + SH1106 OLED + AXP2101 PMIC, native USB-C.
The AXP2101 PMIC gates power to the LoRa chip and the OLED. Without
its init sequence (ALDO3 = 3.3 V for LoRa, ALDO1 = 3.3 V for OLED)
the SX1262 never responds on SPI and radio init fails.
Pin map verified against MeshCore's variants/lilygo_tbeam_supreme_SX1262.
PMIC lives on a dedicated I²C1 bus (SDA=42, SCL=41) separate from the
SH1106 on I²C0 (SDA=17, SCL=18); I²C1 is used blocking for a one-shot
init and then dropped. TCXO at 1.6 V via DIO3.
New src/driver/axp.rs holds the AXP2101 init sequence — kept minimal
(only the LoRa + OLED rails), since DongLoRa is a LoRa-over-USB bridge
and every other rail (GPS, BME280, IMU, SD, batt ADC) is out of scope.
ESP32-S3 + SX1262 + 1.3" SH1106 OLED + CP2102 UART bridge +
1000 mAh Li-Po. Pin map verified against Meshtastic's
variants/esp32s3/ELECROW-ThinkNode-M2. DIO3 TCXO at 3.3 V (vs 1.8 V
on Heltec), VEXT_ENABLE active HIGH (opposite polarity), dedicated
LORA_POWER_EN on GPIO48 sequenced before SPI init. Reuses the
existing async SH1106 driver at I2C address 0x3C.
Refactors hal::esp32s3::{init_spi,init_i2c} and board::esp32s3::init_radio
to accept generic GPIO bounds so ESP32-S3 boards with different pin
assignments can share the helpers. init_radio now takes a
TcxoCtrlVoltage parameter instead of hardcoding Ctrl1V8.
Incidental cleanups needed to make `just check-all` green:
- Replace the core::mem::forget(output) pattern with let _foo = ...;
current esp-hal makes Output non-Drop, so forget is a no-op that
trips clippy's forget_non_drop lint.
- Switch justfile xtensa builds from `cargo +nightly` with a RUSTC
override to `cargo +esp` so the compiler and rust-src versions stay
aligned. Public nightly's rust-src had drifted two months ahead of
the esp fork and broke -Zbuild-std on core.
First RP2040 board and third MCU family (after ESP32-S3 and nRF52840).
Hardware: RP2040 + SX1262 radio, 850-930 MHz HF, PE4259 antenna switch,
LED on GPIO25, no OLED, USB-C via FPC ribbon cable to adapter board.
New files:
- src/hal/rp2040.rs: MCU primitives (SPI bus, USB driver, flash unique ID MAC)
- src/board/waveshare_rp2040_lora.rs: board implementation
- ld/rp2040-memory.x: linker memory layout
Also fixes cortex-m-rt/set-vtor (moved from global dep to per-board feature,
since Cortex-M0+ has no VTOR register) and makes build.rs memory.x selection
target-aware.
The default heltec_v3 feature now uses native USB OTG (same as V4),
appearing as /dev/ttyACM0 with the DongLoRa VID:PID (1209:5741).
This requires a hardware mod: solder R29/R3 and disconnect the CP2102
from the USB data lines.
Stock (unmodified) V3 boards should use the new heltec_v3_uart feature
which preserves the original UART-over-CP2102 behavior (/dev/ttyUSB0).
- heltec_v3: switched from UART to USB OTG
- heltec_v3_uart: new feature, UART fallback for stock boards
- Removed #[cfg] gates on UsbParts/UartParts (both always defined)
- Updated README with hardware mod instructions and board table
- Updated justfile with heltec_v3_uart board definition
swaits