chore: release 1.4.0

The CAD pre-TX loop previously ran up to 10 retries with a fixed 10 ms
sleep — roughly one max-length packet only at SF7/BW500. At SF10/BW125
the 100 ms total was ~4% of one packet; at SF12/BW125 LBT was a no-op.

Now the per-retry sleep is sized to one time-on-air of an assumed-peer
80-byte packet under the active config, cached on RadioContext and
recomputed on every SET_CONFIG. Retries scale as
clamp(floor(BUDGET/T)+1, 1, 10) with BUDGET=2.5 s, so fast configs
still get up to 10 retries while SF11/12 degrade to single-CAD-and-bail
(logged at config-apply). Sleeps are jittered ±20% per iteration to
decorrelate simultaneously-backing-off contenders.

The ToA math, CR→{1..4} mapping, retry-count derivation, and jitter
helper live in a pure src/lbt.rs module so they're host-testable via
DONGLORA_HOST_TEST=1 cargo test (13 tests).

Validated on-device: 20 iterations of the AI Bot test flow that
previously saw ~2 ChannelBusy errors now see zero at the same SF/BW.

.cargo/config.toml

@@ -11,3 +11,10 @@ rustflags = [
     "-C", "link-arg=-Tdefmt.x",
     "-C", "opt-level=z",
 ]
+
+[target.thumbv6m-none-eabi]
+rustflags = [
+    "-C", "link-arg=-Tlink.x",
+    "-C", "link-arg=-Tdefmt.x",
+    "-C", "opt-level=z",
+]

CHANGELOG.md

@@ -0,0 +1,513 @@
+# Changelog
+
+All notable changes to this project will be documented in this file.
+
+The format is based on [Keep a Changelog](https://keepachangelog.com/),
+and this project adheres to [Semantic Versioning](https://semver.org/).
+
+## [Unreleased]
+
+## [1.4.0] - 2026-04-25
+
+### Added
+
+- **RAK4631 WisBlock board support** (nRF52840 + SX1262, RAK19007 base
+  + RAK4631 Core + RAK1921 OLED). The second nRF52840 + SX1262 board
+  alongside the Wio Tracker L1.
+  - `SX126X_POWER_EN` (P1.05) driven HIGH at init — the radio is
+    power-gated on this module; without this the chip has no power
+    and SPI hangs.
+  - HFXO + LFXO external crystals selected in `embassy_nrf::Config`.
+    USB CDC-ACM needs ±500 ppm which the internal RC oscillator
+    can't provide.
+  - `SoftwareVbusDetect(true, true)` so USB enumerates without a
+    `CLOCK_POWER` interrupt handler.
+  - Green LED on P1.03 (RAK19007 Base LED1, active-HIGH) via
+    `SimpleLed`.
+  - Hardware-validated end-to-end: ADVERT round-trip with an external
+    receiver on US915.
+  - Added `debug-checkpoint` blink-map coverage at every TX-phase
+    boundary in `radio.rs`, including a new checkpoint between
+    `prepare_for_cad` and `cad()` so future bring-ups can distinguish
+    a modem-setup hang from a DIO1-wait hang.
+
+- **Adaptive listen-before-talk.** The CAD pre-TX retry loop scales to
+  the active LoRa config instead of running a fixed 10 retries × 10 ms
+  (which was roughly one max-length packet at SF7/BW500 and a no-op at
+  SF12/BW125).
+  - Per-retry sleep is sized to the time-on-air of an assumed-peer
+    80-byte packet under the current SF/BW/CR — cached on
+    `RadioContext`, recomputed on every `SET_CONFIG`.
+  - Retry count = `clamp(floor(BUDGET/T)+1, 1, 10)` with `BUDGET = 2.5
+    s`. Fast configs still get up to 10 retries; SF11/12 degrade to
+    single-CAD-and-bail (logged at config-apply).
+  - Sleeps jittered ±20% per iteration to decorrelate
+    simultaneously-backing-off contenders.
+  - ToA math, CR→{1..4} mapping, retry-count derivation, and jitter
+    helper live in a pure `src/lbt.rs` module — host-testable via
+    `DONGLORA_HOST_TEST=1 cargo test` (13 tests).
+  - Validated on-device: 20 iterations of the AI Bot test flow that
+    previously saw ~2 `ChannelBusy` errors now sees zero at the same
+    SF/BW.
+
+### Fixed
+
+- **First-TX-after-boot reliability on SX1262 boards.** Picked up the
+  upstream `lora-phy` fix that moves the BUSY-handshake check from
+  *after* to *before* each SPI op, per Semtech SX1261/2 §8.3.1, LR1121
+  UM §3, and LR1110 DS §1.2.5. The existing post-op wait is preserved
+  as the belt that closes the BUSY-assertion latency window
+  (T_SW ≤ 600 ns) that a single level-poll can miss. Consumed via
+  `[patch.crates-io]` against `swaits/lora-rs#fix/sx126x-busy-race`
+  until the upstream PR merges.
+  - Hardware-verified on Seeed Wio Tracker L1: 20/20 clean-boot TX
+    (vs ~50% before).
+  - Renames `InterfaceVariant::wait_on_busy` → `wait_until_ready` to
+    match the new semantics.
+- **BUSY pin pull-down → none on nRF SX1262 boards.** SX1262's BUSY
+  pin has an internal 20 kΩ pull-up (datasheet p. 53); our
+  `Input::new(..., Pull::Down)` was contending with it, leaving BUSY
+  at an indeterminate voltage and intermittently mis-reading the
+  chip's ready state. Per `lora-rs/lora-rs#260`, switched to
+  `Pull::None` on both Wio Tracker L1 and RAK4631. The RAK4631
+  appeared to work before, but was affected by the same class of bug
+  per the upstream issue — now deterministically correct rather than
+  "happens to work".
+
+### Changed
+
+- **Build-system DX.** `just flash`, `just flash-probe`, and
+  `just build` accept an optional comma-separated `extra_features`
+  argument that is appended to the board feature, e.g. `just flash
+  wio_tracker_l1 debug-checkpoint`. No more dropping to raw
+  `cargo + rust-objcopy + uf2 cp` for iteration loops.
+- **`just` recipes now resolve all tools through `mise`** via
+  `set shell := ["mise", "exec", "--", "sh", "-c"]`. `cargo`,
+  `espflash`, `rust-objcopy`, `cargo-hex-to-uf2` etc. always pick up
+  the versions pinned in `mise.toml` regardless of `PATH` ordering.
+- **`mise.toml` rust pins now carry ARM targets + clippy**, so a fresh
+  `mise install` is sufficient bootstrapping — no manual
+  `rustup target add` for `thumbv6m-none-eabi` /
+  `thumbv7em-none-eabihf` and no separate clippy install.
+- **New `just flash-dfu` recipe** for the Adafruit nRF52 bootloader
+  (VID:PID `239a:0029`) via `adafruit-nrfutil` under `uvx`, with port
+  autodetect.
+- **Per-board `_info` chain in the justfile** collapsed from a long
+  per-board `if/elif` ladder + per-board `:=` variables into a single
+  `case` statement — one place per board, two lists (names +
+  metadata).
+
+## [1.3.1] - 2026-04-23
+
+### Fixed
+
+- **LilyGo T-Beam (classic) red LED now flashes on TX/RX** instead of
+  dimming off. The red LED under the OLED is wired active-LOW on this
+  board (anode to V+, cathode to GPIO4); v1.3.0 drove it as active-HIGH,
+  so the LED sat lit at idle and briefly dimmed during activity.
+  - Empirically verified on hardware against both T-Beam variants.
+  - Introduces `src/driver/inverted_pin.rs::InvertedPin<P>`, a generic
+    `OutputPin` wrapper that swaps `set_high`/`set_low`. Polarity is
+    expressed at the pin (where the physical wiring lives), so
+    `SimpleLed` stays polarity-agnostic and every other board's code
+    path is byte-for-byte unchanged.
+  - Classic T-Beam now constructs its LED as
+    `SimpleLed(InvertedPin(led_pin))` with pin init at `Level::High`
+    (dark at boot).
+
+## [1.3.0] - 2026-04-23
+
+### Added
+
+- LilyGo T-Beam S3 Supreme board support (ESP32-S3 + SX1262 + SH1106
+  OLED + AXP2101 PMIC, native USB-C).
+  - Pin map verified against MeshCore's
+    `variants/lilygo_tbeam_supreme_SX1262`.
+  - New `src/driver/axp.rs` module with an AXP2101 init sequence
+    (ALDO3 = 3.3 V LoRa, ALDO1 = 3.3 V OLED). The PMIC gates LoRa and
+    display power — without it the SX1262 never responds on SPI.
+  - PMIC lives on a dedicated I²C1 bus (SDA=42, SCL=41), separate
+    from the SH1106 on I²C0 (SDA=17, SCL=18). I²C1 is used blocking
+    for a one-shot init and then dropped.
+  - TCXO driven at 1.6 V via DIO3 (MeshCore uses the same).
+- LilyGo T-Beam (classic) board support (ESP32 + SX1276 + SSD1306
+  OLED + AXP192 PMIC, CP2102 USB-UART bridge). This is the first
+  board in the firmware on classic ESP32 (non-S3) and the first on
+  the SX127x radio family.
+  - Pin map verified against MeshCore's `variants/lilygo_tbeam_SX1276`.
+  - New `src/hal/esp32.rs` (classic-ESP32 MCU primitives, peripheral
+    DMA via `DMA_SPI2`) and `src/board/esp32.rs` (SX1276 radio helper
+    + SSD1306 display pipe).
+  - AXP192 init added to `src/driver/axp.rs`: DCDC1 = 3.3 V for the
+    OLED, LDO2 = 3.3 V for the SX1276 PA_BOOST rail. Shares the
+    OLED I²C bus (SDA=21, SCL=22); the I²C instance is built in
+    blocking mode for PMIC init and converted to async for the
+    display task.
+  - SX127x support via lora-phy 3's `Sx127x<Sx1276>` +
+    `GenericSx127xInterfaceVariant` (DIO0 as the sole IRQ; no
+    BUSY line on SX127x). XTAL clocked (no TCXO), `tx_boost = true`
+    for the PA_BOOST path.
+  - `LoRaBoard` trait gains `supported_sf_bitmap()` and
+    `supported_bw_bitmap()` methods with SX126x defaults
+    (`0x1FE0`, `0x03FF`). T-Beam classic overrides SF to `0x1FC0`
+    (SF6–SF12) — the SX1276 has no SF5.
+  - `radio_chip_id()` reports `0x0011` (`RadioChipId::Sx1276`) and
+    `freq_range_hz()` widens to 137 MHz–1020 MHz per the SX1276
+    datasheet.
+
+### Changed
+
+- `Cargo.toml`: the `esp32s3` chip feature has been moved out of
+  the `esp-hal` / `esp-rtos` / `esp-backtrace` / `esp-println`
+  dependency lines and into each ESP board's feature list (as
+  `esp-hal/esp32s3`, etc.). This lets `lilygo_tbeam` select the
+  classic `esp32` chip flavour from the same dependency set.
+
+## [1.2.1] - 2026-04-23
+
+### Fixed
+
+- **Radio no longer drops to Idle mid-RX-session on transient failures.**
+  Extends the v1.1.0 invariant ("`SET_CONFIG` during RX auto-re-arms")
+  to all failure paths that can occur while a client has RX active:
+  - `Receiving.on(RxFailed) => Idle` now transitions to `ResumingRx`
+    instead of `Idle`. A transient `next_packet` error re-arms the chip
+    rather than ending the RX session.
+  - `TransmittingFromRx.on(TransmitFailed) => Idle` now transitions to
+    `ResumingRx`. TX failure during an active RX session returns
+    `TX_FAILED` to the caller and resumes RX, matching the shape of the
+    adjacent `ChannelBusy` handler.
+  - `ResumingRx.on(StartRxFailed) => Idle` is now a bounded retry
+    (5 × 25 ms backoff via a new `bump_resume_retries` action and a
+    `ResumeRxRetry` / `ResumeRxExhausted` pair of internal events).
+    The chip only lands in `Idle` after exhausting the retry budget —
+    which means it's genuinely wedged and needs reconfiguring.
+
+  Visible effect: the OLED dashboard no longer bounces to Splash when
+  `ai-bot` (or any other client that TXes while RX is running) sends a
+  packet. Previously any of the three transitions above would fire
+  `RadioEvent::Idle`, which the display uses as its `Dashboard → Splash`
+  trigger; the radio would land in `Idle` with no client aware enough
+  to re-send `RX_START`, stranding the dashboard until the session was
+  manually torn down and restarted.
+
+- Removed `announce_rx_failed` helper action: its only purpose was
+  emitting `RadioEvent::Idle` on the now-deleted `Receiving.on(RxFailed)
+  => Idle` edge. No replacement needed — `ResumingRx` handles recovery
+  silently.
+
+## [1.2.0] - 2026-04-22
+
+### Added
+
+- **OLED auto-dim after inactivity.** The display is bright on any
+  activity — splash entry, mode change into a dashboard leaf, packet
+  RX/TX — and dims after a short idle window. Splash holds bright for
+  10 s, then drops to dim while the LearnMore / Info carousel keeps
+  alternating. The dashboard stays bright for 3 s after the last
+  packet or mode change, then dims in place without changing
+  Listening/Transmitting state. Cross-leaf TX↔RX hops transition
+  bright→bright with no intermediate dim — `set_dim` is fired as an
+  action by the 3 s timer handler rather than as a sibling `exit:`
+  action, so mode-change leaf-crossings never see a flash.
+- `DisplayBrightness` trait in `src/driver/mod.rs` unifies the
+  two-level backlight API across the `ssd1306` crate's `Ssd1306Async`
+  and the in-tree `Sh1106` driver. Contrast values centralized as
+  `CONTRAST_BRIGHT` (`0xFF`) and `CONTRAST_DIM` (`0x08`) constants so
+  the two levels can be tuned in one place.
+
+### Changed
+
+- `src/display.rs` statechart restructured:
+  - `Splash` gains `entry: set_bright` plus an action-only
+    `on(after 10s) => set_dim` handler so the splash bright window
+    is time-scoped without disturbing the LM↔Info alternation.
+  - `Dashboard` `Listening` and `Transmitting` each gain a nested
+    `*Bright` substate owning the `entry: set_bright` action. Packet
+    handlers moved into the leaves and target the leaf's `*Bright` —
+    sibling-to-sibling within the leaf restarts the 3 s timer without
+    re-entering the leaf itself (paint / 1 s sparkline timer
+    preserved). The 3 s timeout handler fires `set_dim` as an action
+    and up-transitions to the leaf, parking the machine at the leaf
+    with no active child.
+- `On.on(CmdReset)` now targets `LearnMore` directly rather than
+  `Splash`. Under hsmc 0.2 up-transition semantics, targeting
+  `Splash` from within `Splash.LearnMore` (USB-disconnect race path)
+  would only unwind below `Splash` and park with no active child,
+  leaving the LM↔Info alternation timer dead and the QR frozen on
+  screen.
+- `LoRaBoard::DisplayDriver` trait bound extended with
+  `+ DisplayBrightness` so brightness is part of the board contract
+  alongside `DrawTarget<Color = BinaryColor>`.
+
+### Fixed
+
+- Elecrow ThinkNode-M2 board doc corrected: the shipping revision
+  carries a WCH CH340K USB-UART bridge (USB `1a86:7522`), not a
+  Silicon Labs CP2102. `just flash elecrow_thinknode_m2` now matches
+  the CH340K / CH340 VID:PIDs directly instead of falling through
+  to espflash auto-detect.
+
+### Dependencies
+
+- `hsmc` bumped to `0.2` to pick up the up-transition fix (transition
+  to an already-active ancestor unwinds only the subtree strictly
+  below the target; no exit/entry on the target; no default descent).
+
+## [1.1.0] - 2026-04-22
+
+Small but high-value behavior change: `SET_CONFIG` issued while the
+radio is in continuous RX no longer drops the radio (and the OLED)
+back to idle. The radio now auto-re-arms RX with the new modulation
+once reconfiguration completes, matching DongLoRa Protocol 1.1's
+§3.5 / §6.3 amendments.
+
+### Changed
+
+- `src/radio.rs`: inside `state Receiving`, add `on(ConfigApplied)
+  => ResumingRx` to shadow the parent `Configured` state's
+  `on(ConfigApplied) => Idle` handler. The reconfigure path now
+  runs `apply_set_config` → `ConfigApplied` → `ResumingRx.entry:
+  try_start_rx_hw` → `StartRxOk` → `Receiving` without ever
+  entering `Idle`.
+- The OLED's `Dashboard → Splash` transition was previously driven
+  by `RadioEvent::Idle` firing on `Configured.Idle.entry`. That
+  event no longer fires during a SET_CONFIG-from-Receiving
+  sequence, so the display stays on Dashboard.
+
+### Dependencies
+
+- `donglora-protocol` bumped to `1.1.0` (spec-only change; matches
+  the new normative text the firmware now implements).
+
+### Use-case unlock
+
+- Scanner / time-division / dynamic-modulation workflows that
+  rotate LoRa parameters mid-RX no longer need to re-issue
+  `RX_START` after every `SET_CONFIG`. One call, radio continues
+  to receive.
+
+## [1.0.0] - 2026-04-22
+
+The 1.0 release. Firmware now speaks DongLoRa Protocol v2 end to end,
+depends on the freshly-published `donglora-protocol` 1.0.0 and `hsmc`
+0.1.0 from crates.io, and ships GitHub Release binaries for every
+supported board.
+
+### Breaking
+
+- **DongLoRa Protocol v2 wire format** (wire-incompatible with 0.x
+  clients and firmware). Every `type_id`, tag-correlation rule, and
+  field layout follows `PROTOCOL.md` v1.0.
+- **Host framing replaced.** `src/host/framing.rs` now drives a
+  streaming `FrameDecoder` from `donglora-protocol` and emits
+  `(type_id, tag, payload)` frames; the 0.x COBS-per-response shim is
+  gone.
+- **Radio task reshape.** `src/radio.rs` emits v2 `TX_DONE` /
+  `SetConfigResult` / `RxPayload` / `RxOrigin` shapes directly; no 0.x
+  translation layer remains.
+
+### Changed
+
+- `hsmc` switched from path-dep on the local workspace to
+  `version = "0.1.0"` from crates.io.
+- `donglora-protocol` switched from path-dep on `../protocol` to
+  `version = "1.0.0"` from crates.io; firmware builds are now
+  reproducible from a clean checkout with no sibling repo required.
+- `PROTOCOL.md` updated to the DongLoRa Protocol v2 normative spec,
+  kept byte-for-byte in sync with the `donglora-protocol` crate's
+  copy.
+
+### Infrastructure
+
+- Cargo.toml `repository` + `homepage` now point at the canonical
+  `https://github.com/donglora/firmware` (the `swaits/donglora`
+  repo is archived).
+
+## [0.5.0] - 2026-04-16
+
+### Added
+
+- BLE soft-mesh multiplexer design document (`BLE_MUX_DESIGN_DOC.md`) —
+  specification for turning a dongle from a 1:1 USB device into a shared
+  near-field radio gateway for multiple BLE-attached phones. Three-phase
+  rollout (v1 MVP, v2 hardening, v3 multi-dongle mesh) with regulatory
+  duty-cycle and TX-access-control enforcement from v1. Targets nRF52840
+  first; ESP32-S3 reserved for v2.
+- `debug-checkpoint` cargo feature with a dedicated `debug_blink` task and
+  a latching atomic checkpoint — LED-pattern diagnostic for UART-only
+  boards where defmt output would corrupt the host protocol. Zero
+  footprint when the feature is off.
+
+### Changed
+
+- Radio task rewritten as an `hsmc` statechart (`Unconfigured` /
+  `Configured.{Idle, StartingRx, Receiving, ResumingRx,
+  Transmitting.{FromIdle, FromRx}}`). The main loop is now a single
+  `machine.run().await`; command reading, packet RX, and TX are
+  state-scoped `during:` activities. Post-TX RX re-arm is modeled as
+  state identity (`TransmittingFromRx` → `ResumingRx`) instead of a
+  `was_receiving` flag.
+- Display task rewritten as an `hsmc` statechart (`Off` /
+  `On.{Splash.{LearnMore, Info}, Dashboard.{Listening, Transmitting}}`).
+  The 5 s splash alternation and 1 s sparkline tick use `on(after …)` /
+  `on(every …)` transitions — no external timer task.
+- USB host task now carries a small `hsmc` statechart (`Disconnected` /
+  `Connected`) whose entry/exit actions handle display wake, radio
+  `StopRx`, and display reset — replacing the open-coded `was_connected`
+  edge detector.
+- Radio → Display channel switched from a `RadioStatus` watch to a typed
+  `RadioEvent` queue. The radio emits discrete `EnteredRx` / `EnteredTx`
+  / `Idle` / `PacketRx` / `PacketTx` / `ConfigChanged` events; downstream
+  consumers observe transitions directly rather than diffing snapshots.
+- Wire protocol types and COBS framing moved out of firmware into the
+  shared `donglora-protocol` crate (path dep on `../protocol`). Firmware
+  `src/protocol.rs` is now a re-export shim preserving every call site;
+  `src/host/framing.rs` keeps only the embassy-specific `route_command`.
+
+### Fixed
+
+- USB disconnect recovery: on a read error the DTR-edge-detect branch
+  now runs unconditionally (was early-continuing in some paths, starving
+  the display-reset / radio-stop handoff).
+
+## [0.4.0] - 2026-04-11
+
+### Added
+
+- ELECROW ThinkNode-M2 board support (ESP32-S3 + SX1262 + 1.3" SH1106 OLED
+  via CP2102 UART bridge, 1000 mAh Li-Po handheld)
+  - Pin map verified against Meshtastic's
+    `variants/esp32s3/ELECROW-ThinkNode-M2`
+  - DIO3 TCXO driven at 3.3 V (not 1.8 V like Heltec)
+  - Dedicated `LORA_POWER_EN` (GPIO48) sequenced HIGH before SPI init
+  - `VEXT_ENABLE` (GPIO46) is active HIGH — opposite polarity from Heltec
+  - Reuses the existing async SH1106 driver at I2C address 0x3C
+
+### Changed
+
+- `hal::esp32s3::{init_spi, init_i2c}` and `board::esp32s3::init_radio` are
+  now generic over GPIO type, so ESP32-S3 boards with different pin
+  assignments can share the helpers.
+- `board::esp32s3::init_radio` takes a `TcxoCtrlVoltage` parameter instead
+  of hardcoding `Ctrl1V8` — needed for ThinkNode-M2's 3.3 V TCXO.
+- SSD1306 display items in `board::esp32s3` are now cfg-gated to Heltec
+  boards (ThinkNode-M2 supplies its own SH1106 `create_display`).
+- `justfile` uses `cargo +esp` for Xtensa targets instead of `cargo +nightly`
+  with a `RUSTC=esp` override — the self-contained esp toolchain keeps its
+  cargo, rustc, and rust-src versions aligned. Public nightly's rust-src
+  had drifted ahead of the esp fork, breaking `-Zbuild-std`.
+- Migrated to embassy-executor 0.10 and embassy-rp 0.10
+- ESP crates (esp-hal, esp-rtos, esp-backtrace, esp-println) patched from
+  esp-rs/esp-hal main branch until esp-rtos publishes with 0.10 support
+- Adapted to embassy-executor 0.10 SpawnToken API (task functions now return
+  `Result<SpawnToken, SpawnError>`, `Spawner::spawn` no longer returns Result)
+- Adapted to esp-hal main branch API changes: `efuse::base_mac_address()`,
+  `esp_rtos::start` now requires `SoftwareInterrupt`, embassy-rp SPI
+  constructor now requires DMA interrupt bindings
+- `just check` now runs clippy with `-D warnings` instead of plain `cargo check`
+- Rust toolchain bumped to 1.94 in mise.toml
+
+### Fixed
+
+- `core::mem::forget(output)` pattern in ESP32-S3 board files is now
+  `let _vext = Output::new(...)` — current esp-hal makes `Output` non-Drop,
+  which made `forget` a no-op and tripped clippy's `forget_non_drop` lint.
+- UART boards (heltec_v3_uart) display stuck on splash screen after boot.
+  Host task sent `DisplayCommand::Reset` (which sets disconnected=true) instead
+  of `DisplayCommand::On`. UART has no DTR, so nothing ever cleared it.
+
+## [0.3.0] - 2026-04-10
+
+### Added
+
+- Waveshare RP2040-LoRa board support (RP2040 + SX1262, no OLED, LED on GPIO25)
+  - First RP2040 board — third MCU family after ESP32-S3 and nRF52840
+  - New `hal/rp2040.rs` module with MCU primitives (SPI, USB, flash unique ID)
+  - USB-C via FPC ribbon cable to adapter board
+  - PE4259 antenna switch on GPIO17, 850-930 MHz (HF)
+
+### Changed
+
+- `cortex-m-rt/set-vtor` moved from global dependency to per-board feature
+  (Cortex-M0+ has no VTOR register)
+- `build.rs` memory.x selection is now target-aware (thumbv6m vs thumbv7em)
+
+## [0.2.1] - 2026-04-07
+
+### Fixed
+
+- Display stuck on status screen after USB disconnect (stale radio status
+  updates re-rendered dashboard over splash because `disconnected` flag was
+  not set in the `Reset` handler)
+- Radio left running after host disconnect, now sends `StopRx` when DTR drops
+- System deadlock when host app closes serial port while radio is receiving
+  (unsolicited responses in radio task now use `try_send` to avoid blocking
+  on a full response channel)
+- LED orphaned if OLED display initialization fails (display task now falls
+  back to a LED-only event loop instead of returning early)
+
+## [0.2.0] - 2026-04-07
+
+### Added
+
+- Wio Tracker L1 board support (nRF52840 + SX1262, SH1106 OLED)
+- LED blink on packet activity: brief flash on RX and TX when display is on
+  - RX brightness scales with SNR (stronger signal = brighter)
+  - Works on all boards with a user LED (Heltec V3/V4, Wio Tracker)
+- Native USB CDC-ACM support for Heltec V3 (requires hardware mod: solder R29/R3)
+- `heltec_v3_uart` feature for stock (unmodified) V3 boards via CP2102 bridge
+- `RgbLed` trait and `SimpleLed` driver for GPIO-based LEDs
+- `LoRaBoard` trait with full associated types (`RadioParts`, `CommParts`,
+  `DisplayParts`, `DisplayDriver`, `LedDriver`) and `BoardParts<R, C, D, L>` struct
+
+### Changed
+
+- Major firmware architecture reorganization:
+  - `hal/` module for MCU-specific primitives (ESP32-S3, nRF52840)
+  - `driver/` module for hardware peripheral drivers (SH1106, SimpleLed)
+  - `host/` module for unified USB/UART communication with internal cfg dispatch
+  - `board/` contains only board definitions — no MCU helpers or drivers mixed in
+  - Board files are declarative wiring diagrams calling hal primitives
+- `run()` function has zero board-specific conditional compilation
+- Display init moved to board layer (`create_display()`) — display task has no cfg
+- Flattened `radio/` and `display/` directories (no single-file directories)
+- `build.rs` auto-discovers boards by content (implements `LoRaBoard`) and
+  helper modules by `use super::` imports — no exclusion lists
+- `check` and `clippy` commands now use `--release` profile
+- Deduplicated USB/UART protocol framing (shared `CobsDecoder` + `route_command`)
+- Removed `ErrorCode::CrcError` (SX1262 silently drops bad-CRC packets)
+
+### Fixed
+
+- Display stuck on splash screen for UART boards (disconnected flag started true)
+
+## [0.1.0] - 2026-03-15
+
+### Added
+
+- Transparent LoRa radio over USB CDC-ACM (VID `1209`, PID `5741`)
+- COBS-framed fixed-size LE binary protocol (9 commands, 7 responses)
+- Radio configuration: frequency, bandwidth, spreading factor, coding rate, TX power
+- Continuous RX mode with RSSI/SNR per packet
+- Single-shot TX with optional per-packet config override
+- SSD1306 OLED display support with status dashboard
+  - Radio state, frequency, modulation parameters
+  - Packet counters (RX/TX)
+  - RSSI sparkline (1-minute history, TX shown as dotted bars)
+  - Combined splash/waiting screen on disconnect
+- Auto-detect USB host connect/disconnect via DTR
+- Config validation against per-board hardware limits
+- `TX_POWER_MAX` sentinel (`-128`): auto-use the board's maximum TX power
+- Board support: Heltec V3, Heltec V4, RAK WisBlock 4631
+- Python host library (`donglora` on PyPI) with `pip install` and `donglora-mux` CLI
+- USB multiplexer for sharing one dongle with multiple applications
+- Two-way LoRa bridge over TCP (`examples/lora_bridge.py`)
+
+### Technical
+
+- Embassy async runtime (no threads, CPU sleeps when idle)
+- Zero-config: boots and waits for host commands
+- Protocol-agnostic: firmware has no opinion about what you transmit
+- Tasks never panic: all errors reported to host or logged
+- Board abstraction: one `.rs` file + one Cargo feature per board

Cargo.toml

@@ -3,20 +3,19 @@ members = ["."]
 
 [package]
 name = "donglora"
-version = "0.2.0"
+version = "1.4.0"
 edition = "2021"
 build = "build.rs"
 authors = ["Stephen Waits <steve@waits.net>"]
 license = "MIT"
 description = "Transparent LoRa radio over USB — plug in a board, talk LoRa from your host"
-repository = "https://github.com/swaits/donglora"
+repository = "https://github.com/donglora/firmware"
+homepage = "https://github.com/donglora/firmware"
 keywords = ["lora", "radio", "embedded", "usb", "firmware"]
 categories = ["embedded", "hardware-support", "no-std"]
 
-# UPGRADE BLOCKED: embassy-executor 0.10 and ucobs 0.3 need Rust >= 1.93
-# stable. The ESP Xtensa toolchain (espup) is a nightly fork that may not
-# support the required language features or pass MSRV gating. Revisit when
-# espup catches up. Check: rustup run esp rustc --version
+# NOTE: esp-rtos patched from GitHub main (see [patch.crates-io] below).
+# Remove patches once esp-rtos publishes with embassy-executor 0.10 support.
 [dependencies]
 cfg-if = "1.0"
 critical-section = "1.2"
@@ -24,14 +23,20 @@ defmt = "1.0"
 embedded-hal = "1.0"
 embedded-hal-async = "1.0"
 embassy-embedded-hal = "0.6"
-embassy-executor = "0.9"
+embassy-executor = "0.10"
 embassy-sync = "0.8"
 embassy-time = "0.5"
 embassy-usb = { version = "0.6", features = ["defmt"] }
 embassy-usb-driver = "0.2"
 ucobs = { version = "0.3", features = ["legacy-msrv"] }
 heapless = "0.9"
-lora-phy = "3.0"
+donglora-protocol = "1"
+hsmc = { version = "0.2", default-features = false, features = ["embassy"] }
+# Pulled from swaits/lora-rs fork until lora-rs/lora-rs#428 (pre-command
+# BUSY check) is merged + released on crates.io. Switch back to a normal
+# crates.io version then.
+lora-phy = { git = "https://github.com/swaits/lora-rs.git", branch = "fix/sx126x-busy-race", features = ["defmt-03"] }
+portable-atomic = { version = "1", optional = true, default-features = false, features = ["critical-section"] }
 static_cell = "2.1"
 
 # Display rendering
@@ -43,28 +48,28 @@ ssd1306 = { version = "0.10", features = ["async"] }
 embedded-io-async = "0.7"
 embassy-futures = "0.1"
 
-# ESP32-S3 (Heltec V3) — requires esp toolchain (espup)
+# Xtensa ESP crates — requires esp toolchain (espup). The chip feature
+# (esp32 / esp32s3) is selected per board via the board-level feature flag
+# below, so the same dep lines support both classic ESP32 and ESP32-S3.
 esp-backtrace = { version = "0.18", optional = true, features = [
-  "esp32s3",
   "panic-handler",
   "defmt",
 ] }
 esp-hal = { version = "1.0", optional = true, features = [
-  "esp32s3",
   "unstable",
 ] }
 esp-println = { version = "0.16", optional = true, features = [
-  "esp32s3",
   "defmt-espflash",
 ] }
 esp-rtos = { version = "0.2", optional = true, features = [
-  "esp32s3",
   "embassy",
 ] }
 
 # nRF52840 (RAK 4631)
-cortex-m = { version = "0.7", optional = true, features = ["critical-section-single-core"] }
-cortex-m-rt = { version = "0.7", optional = true, features = ["set-vtor"] }
+cortex-m = { version = "0.7", optional = true, features = [
+  "critical-section-single-core",
+] }
+cortex-m-rt = { version = "0.7", optional = true }
 defmt-rtt = { version = "1.0", optional = true }
 embassy-nrf = { version = "0.10", optional = true, features = [
   "nrf52840",
@@ -74,47 +79,141 @@ embassy-nrf = { version = "0.10", optional = true, features = [
 ] }
 panic-probe = { version = "1.0", optional = true, features = ["print-defmt"] }
 
+# RP2040 (Waveshare RP2040-LoRa)
+embassy-rp = { version = "0.10", optional = true, features = [
+  "rp2040",
+  "time-driver",
+  "defmt",
+] }
+
 [build-dependencies]
 minijinja = "2.18"
 owo-colors = "4.3"
 
 [features]
+# The `embassy` feature gates the async-actions codepath inside the `hsmc`
+# statechart macro. Its `#[cfg(feature = "embassy")]` attributes are
+# evaluated in *this* crate's context (a proc-macro cfg quirk), so every
+# board feature must enable it. `tokio` is declared only to silence the
+# macro's `#[cfg(feature = "tokio")]` checks.
+embassy = []
+tokio = []
+# When enabled, replaces the display task with a LED-based diagnostic
+# blinker driven by `crate::debug_blink::CHECKPOINT`. Used for diagnosing
+# the firmware on UART-only boards where defmt output would corrupt the
+# host protocol on the same UART. The LED flashes N times then pauses —
+# a human watches the pattern and reports N to determine where execution
+# reached / stopped.
+debug-checkpoint = []
 heltec_v3 = [
+  "embassy",
   "dep:esp-backtrace",
   "dep:esp-hal",
   "dep:esp-println",
   "dep:esp-rtos",
+  "esp-backtrace/esp32s3",
+  "esp-hal/esp32s3",
+  "esp-println/esp32s3",
+  "esp-rtos/esp32s3",
 ]
 heltec_v3_uart = [
+  "embassy",
   "dep:esp-backtrace",
   "dep:esp-hal",
   "dep:esp-println",
   "dep:esp-rtos",
+  "esp-backtrace/esp32s3",
+  "esp-hal/esp32s3",
+  "esp-println/esp32s3",
+  "esp-rtos/esp32s3",
 ]
 heltec_v4 = [
+  "embassy",
   "dep:esp-backtrace",
   "dep:esp-hal",
   "dep:esp-println",
   "dep:esp-rtos",
+  "esp-backtrace/esp32s3",
+  "esp-hal/esp32s3",
+  "esp-println/esp32s3",
+  "esp-rtos/esp32s3",
+]
+elecrow_thinknode_m2 = [
+  "embassy",
+  "dep:esp-backtrace",
+  "dep:esp-hal",
+  "dep:esp-println",
+  "dep:esp-rtos",
+  "esp-backtrace/esp32s3",
+  "esp-hal/esp32s3",
+  "esp-println/esp32s3",
+  "esp-rtos/esp32s3",
+]
+lilygo_tbeam_supreme = [
+  "embassy",
+  "dep:esp-backtrace",
+  "dep:esp-hal",
+  "dep:esp-println",
+  "dep:esp-rtos",
+  "esp-backtrace/esp32s3",
+  "esp-hal/esp32s3",
+  "esp-println/esp32s3",
+  "esp-rtos/esp32s3",
+]
+lilygo_tbeam = [
+  "embassy",
+  "dep:esp-backtrace",
+  "dep:esp-hal",
+  "dep:esp-println",
+  "dep:esp-rtos",
+  "esp-backtrace/esp32",
+  "esp-hal/esp32",
+  "esp-println/esp32",
+  "esp-rtos/esp32",
 ]
 rak_wisblock_4631 = [
+  "embassy",
   "dep:cortex-m",
   "dep:cortex-m-rt",
+  "cortex-m-rt/set-vtor",
   "dep:defmt-rtt",
   "dep:embassy-nrf",
   "dep:panic-probe",
-  "embassy-executor/arch-cortex-m",
+  "embassy-executor/platform-cortex-m",
   "embassy-executor/executor-thread",
 ]
 wio_tracker_l1 = [
+  "embassy",
   "dep:cortex-m",
   "dep:cortex-m-rt",
+  "cortex-m-rt/set-vtor",
   "dep:defmt-rtt",
   "dep:embassy-nrf",
   "dep:panic-probe",
-  "embassy-executor/arch-cortex-m",
+  "embassy-executor/platform-cortex-m",
   "embassy-executor/executor-thread",
 ]
+waveshare_rp2040_lora = [
+  "embassy",
+  "dep:cortex-m",
+  "dep:cortex-m-rt",
+  "dep:defmt-rtt",
+  "dep:embassy-rp",
+  "dep:panic-probe",
+  "dep:portable-atomic",
+  "embassy-executor/platform-cortex-m",
+  "embassy-executor/executor-thread",
+]
+
+# REVISIT: esp-rtos 0.2.0 on crates.io pins embassy-executor ^0.9. The
+# esp-rs/esp-hal main branch already supports 0.10. Remove these patches once
+# esp-rtos publishes a release with embassy-executor 0.10 support. Track:
+#   https://github.com/esp-rs/esp-hal/tree/main/esp-rtos
+[patch.crates-io]
+esp-hal       = { git = "https://github.com/esp-rs/esp-hal.git", branch = "main" }
+esp-rtos      = { git = "https://github.com/esp-rs/esp-hal.git", branch = "main" }
+esp-backtrace = { git = "https://github.com/esp-rs/esp-hal.git", branch = "main" }
+esp-println   = { git = "https://github.com/esp-rs/esp-hal.git", branch = "main" }
 
 [lints.clippy]
 undocumented_unsafe_blocks = "deny"
@@ -122,6 +221,6 @@ undocumented_unsafe_blocks = "deny"
 [profile.release]
 codegen-units = 1
 lto = "fat"
-opt-level = 3  # "s"/"z" break Xtensa (l32r literal range exceeded)
+opt-level = 3     # "s"/"z" break Xtensa (l32r literal range exceeded)
 panic = "abort"
 strip = true

LICENSE

@@ -0,0 +1,21 @@
+MIT License
+
+Copyright (c) 2026 Stephen Waits <steve@waits.net>
+
+Permission is hereby granted, free of charge, to any person obtaining a copy
+of this software and associated documentation files (the "Software"), to deal
+in the Software without restriction, including without limitation the rights
+to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+copies of the Software, and to permit persons to whom the Software is
+furnished to do so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in all
+copies or substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+SOFTWARE.

README.md

@@ -23,7 +23,11 @@ All commands are run from the `firmware/` directory.
 | Heltec V3 | `heltec_v3` | ESP32-S3 | SX1262 | Native CDC-ACM | xtensa-esp32s3-none-elf |
 | Heltec V3 (UART) | `heltec_v3_uart` | ESP32-S3 | SX1262 | CP2102 bridge | xtensa-esp32s3-none-elf |
 | Heltec V4 | `heltec_v4` | ESP32-S3 | SX1262 | Native CDC-ACM | xtensa-esp32s3-none-elf |
+| ELECROW ThinkNode-M2 | `elecrow_thinknode_m2` | ESP32-S3 | SX1262 | CP2102 bridge | xtensa-esp32s3-none-elf |
+| LilyGo T-Beam | `lilygo_tbeam` | ESP32 | SX1276 | CP2102 bridge | xtensa-esp32-none-elf |
+| LilyGo T-Beam S3 Supreme | `lilygo_tbeam_supreme` | ESP32-S3 | SX1262 | Native CDC-ACM | xtensa-esp32s3-none-elf |
 | RAK WisBlock 4631 | `rak_wisblock_4631` | nRF52840 | SX1262 | Native CDC-ACM | thumbv7em-none-eabihf |
+| Waveshare RP2040-LoRa | `waveshare_rp2040_lora` | RP2040 | SX1262 | Native CDC-ACM | thumbv6m-none-eabi |
 | Wio Tracker L1 | `wio_tracker_l1` | nRF52840 | SX1262 | Native CDC-ACM | thumbv7em-none-eabihf |
 
 ### Heltec V3 USB Note

TODO.md

@@ -1,4 +1,165 @@
-- LED blinking on TX/RX? colored?
-- publish new client, mux, bridge (updates in client for UART crap)
-- split out mux and client repos
-- move to GH organization
+# Firmware TODO List
+
+## `lora-phy` fix: drop fork pin once PR #428 merges + releases
+
+Upstream PR: [lora-rs/lora-rs#428 — *phy: add pre-command BUSY checks
+per Semtech datasheets*](https://github.com/lora-rs/lora-rs/pull/428)
+(open).
+Fork branch we ship from:
+[`swaits/lora-rs @ fix/sx126x-busy-race`](https://github.com/swaits/lora-rs/tree/fix/sx126x-busy-race).
+
+Firmware consumes the fix via a direct `git` dependency in
+`Cargo.toml`:
+
+```toml
+lora-phy = { git = "https://github.com/swaits/lora-rs.git", branch = "fix/sx126x-busy-race", features = ["defmt-03"] }
+```
+
+When PR #428 merges and a `lora-phy` release ships on crates.io that
+contains it, switch this line back to a normal `lora-phy = "X.Y"`
+crates.io version and drop the explanatory comment block above it.
+
+Hardware-verified on Wio Tracker L1: 20/20 clean-boot TX after the fix
+(vs ~50% before). The fix adds a pre-command BUSY check before each
+`SpiInterface` read/write op, keeping the existing post-command wait
+in place — belt-and-suspenders bracketing that closes the
+BUSY-assertion latency window (T_SW ≤ 600 ns) a single level-poll can
+miss.
+
+---
+
+## Drop `[patch.crates-io]` + upgrade esp-hal / esp-rtos + add `esp_app_desc!()` + bump espflash to v4
+
+Single coordinated change that clears our last remaining dep-graph debt
+on the ESP boards. All four pieces are coupled, so they land together.
+
+### Why
+
+Today `Cargo.toml` overrides `esp-hal`, `esp-rtos`, `esp-backtrace`, and
+`esp-println` with a git pin to `esp-rs/esp-hal#main`. The note in that
+block explains the historical reason:
+
+> REVISIT: esp-rtos 0.2.0 on crates.io pins embassy-executor ^0.9. The
+> esp-rs/esp-hal main branch already supports 0.10. Remove these
+> patches once esp-rtos publishes a release with embassy-executor 0.10
+> support.
+
+**That condition is now met.** `esp-rtos 0.3.0` is published on crates.io
+and depends on `embassy-executor ^0.10` and `esp-hal ~1.1.0-rc.0` — exactly
+what our patches were pulling unofficially. Keeping the patches is no
+longer free: it blocks `espflash` v4, blocks `esp-bootloader-esp-idf`, and
+ties reproducible builds to whatever commit happens to be on
+`esp-rs/esp-hal#main`.
+
+The immediate trigger is `espflash` v4's required
+`esp_bootloader_esp_idf::esp_app_desc!()` check. `save-image` refuses any
+ESP binary that lacks the IDF app descriptor. The crate that provides the
+macro (`esp-bootloader-esp-idf`) uses the same `esp-rom-sys` native
+library as `esp-hal` — two copies of the same `links = "esp_rom_sys"` is
+a hard cargo error, so `esp-bootloader-esp-idf` must come from the _same
+source_ as `esp-hal`. Easiest way to guarantee that: both from crates.io,
+no patches.
+
+### What changes
+
+1. **`Cargo.toml`** — delete the entire `[patch.crates-io]` block and the
+   preceding `REVISIT:` comment. Bump the four esp-rs deps to published
+   versions:
+   - `esp-hal = "1.0"` → `"1.1.0-rc.0"` (pre-release selector — see Gotchas)
+   - `esp-rtos = "0.2"` → `"0.3"`
+   - `esp-backtrace = "0.18"` → whatever matches esp-rtos 0.3 (check its deps)
+   - `esp-println = "0.16"` → same
+     Add a new optional dep + feature wiring for
+     `esp-bootloader-esp-idf = "0.5"` with `defmt` feature, plus per-board
+     chip feature (`esp-bootloader-esp-idf/esp32s3` for the S3 boards,
+     `esp-bootloader-esp-idf/esp32` for LilyGo T-Beam classic).
+
+2. **`src/main.rs`** — inside the ESP-family branch of the existing
+   `cfg_if!` block (around line 51), invoke the macro at module scope:
+
+   ```rust
+   esp_bootloader_esp_idf::esp_app_desc!();
+   ```
+
+   Zero runtime cost. Emits ~256 bytes in `.rodata_desc` with app
+   metadata (name, version, build date) that the ESP-IDF 2nd-stage
+   bootloader + `espflash save-image` look for.
+
+3. **`mise.toml`** — `"cargo:espflash" = "3"` → `"4"`. Drop the deferral
+   comment on that line.
+
+4. **Possible API drift fixes** — esp-hal's pre-release versions
+   occasionally rename or move items. Most likely touch points:
+   - `src/board/esp32.rs`, `src/board/esp32s3.rs`
+   - Any board file in `src/board/heltec_*.rs`, `lilygo_*.rs`,
+     `elecrow_*.rs` that calls into esp-hal / esp-rtos init
+     Run `just check-all` after steps 1–3 and patch up whatever surfaces.
+     Don't guess — read the actual compiler errors.
+
+### How (step by step)
+
+1. `jj new -m "chore(esp): drop esp-hal patches, bump to published versions, add esp_app_desc!()"`
+2. Edit `Cargo.toml` — delete `[patch.crates-io]` + `REVISIT:` comment;
+   bump the four versions; add `esp-bootloader-esp-idf` dep + feature
+   wiring for each ESP board feature block.
+3. Edit `src/main.rs` — add `esp_bootloader_esp_idf::esp_app_desc!();`
+   to the ESP branch of the top-level `cfg_if!`.
+4. Edit `mise.toml` — espflash `"3"` → `"4"`.
+5. `mise install` to pull espflash 4.x.
+6. `cargo update` to let the resolver pick a consistent tree with the
+   new requirements.
+7. `just check-all` — expect some compilation errors from API drift on
+   ESP boards. Fix them one at a time; consult the official examples
+   in `esp-rs/esp-hal` if in doubt.
+8. `just build heltec_v3` (or any ESP board you have) — verify
+   `espflash save-image` now succeeds end-to-end producing a valid
+   `.bin`.
+9. Flash to real hardware if available. **The RAK4631 and Wio Tracker
+   L1 (nRF52) boards should be untouched.**
+
+### Verification
+
+- `just check-all` clean on all 9 boards.
+- `just test` (host-side protocol tests) still green.
+- For each ESP board that has been physically validated before
+  (Heltec V3, LilyGo T-Beam units): flash + confirm radio TX works
+  end-to-end via ai-bot or a known peer.
+- RAK4631 + Wio Tracker L1 unchanged; re-check via `just check` on
+  both, but no re-flash needed (they don't go through the ESP code
+  path).
+
+### Gotchas
+
+- **Pre-release version selector**: `esp-hal = "1.1.0-rc.0"` by itself
+  does NOT match pre-release versions in cargo's default semver rules.
+  Use an exact pre-release like `"1.1.0-rc.0"`, `"~1.1.0-rc.0"` (only
+  `1.1.0-rc.0`, `1.1.0-rc.1`, … with any patch), or `">=1.1.0-rc.0"`.
+  `"1.1"` will NOT resolve to a pre-release.
+- **Two copies of `esp-rom-sys`**: the root cause of the first failed
+  attempt at this task. If cargo errors with _"Only one package in the
+  dependency graph may specify the same links value"_ for
+  `esp_rom_sys`, it means `esp-hal` and `esp-bootloader-esp-idf` are
+  being pulled from different sources (one crates.io, one git). Either
+  both from crates.io (this task's plan) or both from the same git
+  commit.
+- **`esp-bootloader-esp-idf` chip features**: the crate needs exactly
+  one of `esp32 / esp32s3 / esp32c3 / esp32c6 / …` to be enabled.
+  Without it, the build panics at its `build.rs`: _"Expected exactly
+  one of the following features to be enabled: esp32, esp32c2, ..."_.
+  Wire per-board the same way we wire `esp-hal/esp32s3` etc.
+- **Probe-less repro**: `mise install` after bumping espflash to "4"
+  only installs mise's copy. If the user's global
+  `~/.cargo/bin/espflash` is stale/different, it still wins on PATH.
+  The justfile `set shell := ["mise", "exec", "--", "sh", "-c"]`
+  prepends mise's paths but does NOT reorder `~/.cargo/bin` ahead of
+  them. Either `cargo uninstall espflash` globally, or change the
+  justfile recipes to call `$(mise which espflash)` explicitly.
+
+### Why not now
+
+Tried it alongside the RAK4631 bring-up in April 2026 and bounced off
+the `esp-rom-sys` two-copies problem. Backed out the attempt and left
+espflash pinned at v3 + the patches in place so the bring-up commit
+stayed atomic and shippable. This task is what's needed to unblock v4
+properly, but it deserves its own focused session — not as
+"while-I'm-here" scope on a board bring-up.

build.rs

@@ -108,14 +108,19 @@ fn main() {
     println!("cargo:rerun-if-changed=src/board/mod.rs.j2");
     println!("cargo:rerun-if-changed={}", board_dir);
 
-    // cortex-m-rt's link.x does `INCLUDE memory.x`. Copy our nRF layout into
-    // OUT_DIR so it's only visible to ARM builds.
+    // cortex-m-rt's link.x does `INCLUDE memory.x`. Copy the correct layout
+    // into OUT_DIR based on the target MCU family.
     let target = std::env::var("TARGET").unwrap_or_default();
-    if !target.starts_with("xtensa") {
+    let memory_x = match target.as_str() {
+        "thumbv7em-none-eabihf" => Some("ld/nrf52840-memory.x"),
+        "thumbv6m-none-eabi" => Some("ld/rp2040-memory.x"),
+        _ => None,
+    };
+    if let Some(src) = memory_x {
         let out_dir = std::env::var("OUT_DIR").unwrap();
-        fs::copy("ld/nrf52840-memory.x", format!("{out_dir}/memory.x"))
-            .expect("failed to copy ld/nrf52840-memory.x");
+        fs::copy(src, format!("{out_dir}/memory.x")).expect("failed to copy memory.x");
         println!("cargo:rustc-link-search={out_dir}");
     }
     println!("cargo:rerun-if-changed=ld/nrf52840-memory.x");
+    println!("cargo:rerun-if-changed=ld/rp2040-memory.x");
 }

justfile

@@ -1,35 +1,29 @@
-set shell := ["bash", "-c"]
-
-# Board definitions: feature target chip
-# Xtensa targets use nightly cargo + esp rustc + -Zbuild-std=core.
-# Tool versions are pinned in mise.toml; run `just setup` to install everything.
-heltec_v3      := "heltec_v3 xtensa-esp32s3-none-elf esp32s3"
-heltec_v3_uart := "heltec_v3_uart xtensa-esp32s3-none-elf esp32s3"
-heltec_v4      := "heltec_v4 xtensa-esp32s3-none-elf esp32s3"
-rak_wisblock_4631  := "rak_wisblock_4631 thumbv7em-none-eabihf nRF52840_xxAA"
-wio_tracker_l1     := "wio_tracker_l1 thumbv7em-none-eabihf nRF52840_xxAA"
+# Run every recipe with mise's tool versions active — so `just` invocations
+# of cargo, espflash, rust-objcopy, etc. always resolve to the pinned
+# versions in mise.toml, even if the user has a different version elsewhere
+# on PATH (e.g. a stray `cargo install espflash`).
+set shell := ["mise", "exec", "--", "sh", "-c"]
 
 builds_dir := "builds"
 version := `sed -n 's/^version = "\(.*\)"/\1/p' Cargo.toml`
 
-# All known boards
-boards := "heltec_v3 heltec_v3_uart heltec_v4 rak_wisblock_4631 wio_tracker_l1"
+# All known boards. ADD A NEW BOARD HERE and in the `_info` case below.
+#
+# Board metadata ("feature target chip") lives in the `_info` recipe —
+# Xtensa targets are built with `+esp` + `-Zbuild-std=core,alloc` (the
+# self-contained esp toolchain ships its own rust-src; the public
+# nightly drifts ahead and breaks core-stdlib compilation).
+boards := "heltec_v3 heltec_v3_uart heltec_v4 elecrow_thinknode_m2 lilygo_tbeam lilygo_tbeam_supreme rak_wisblock_4631 waveshare_rp2040_lora wio_tracker_l1"
 
 # Install all required tools and toolchains
 setup:
     mise trust --yes
     mise install
-    @# ESP Xtensa toolchain (not managed by mise)
+    @# ESP Xtensa toolchain (not a rustup component — installed out-of-band by espup)
     @if ! rustup toolchain list | grep -q "^esp"; then \
         echo "ESP toolchain not found, installing via espup (this may take a while)..."; \
         espup install || { echo "error: espup install failed" >&2; exit 1; }; \
     fi
-    @# nightly rust-src for -Zbuild-std
-    @if ! rustup component list --toolchain nightly --installed 2>/dev/null | grep -q "^rust-src"; then \
-        rustup component add rust-src --toolchain nightly; \
-    fi
-    @# ARM target
-    @rustup target list --installed | grep -q "^thumbv7em-none-eabihf$" || rustup target add thumbv7em-none-eabihf
 
 # Build release firmware for all boards, installing toolchains as needed
 build-all:
@@ -55,27 +49,27 @@ check-all:
         fi; \
     done
 
-# Check a single board compiles
+# Check a single board compiles (clippy with warnings as errors)
 check board:
-    @just _cargo {{board}} "check --release"
-
-# Run clippy on a single board
-clippy board:
     @just _cargo {{board}} "clippy --release" "-- -D warnings"
 
-# Build release firmware and copy to builds/ with a readable name
-build board profile="release":
-    @just _cargo {{board}} "build --{{profile}}"
+# Build release firmware and copy to builds/ with a readable name.
+# `extra_features` (comma-separated) is appended to the board feature,
+# e.g. `just build wio_tracker_l1 release debug-checkpoint`.
+build board profile="release" extra_features="":
+    @just _cargo {{board}} "build --{{profile}}" "" "{{extra_features}}"
     @just _copy_firmware {{board}} {{profile}}
 
-# Build and flash a board (espflash for Xtensa, UF2 DFU for ARM)
-flash board:
+# Build and flash a board (espflash for Xtensa, UF2 DFU for ARM).
+# `extra_features` is passed through to the build, e.g.
+# `just flash wio_tracker_l1 debug-checkpoint`.
+flash board extra_features="":
     @just _ensure_tools
-    @just build {{board}} release
-    @read -r feat target chip <<< "$(just _info {{board}})"; \
+    @just build {{board}} release "{{extra_features}}"
+    @set -- $(just _info {{board}}); feat=$1; target=$2; chip=$3; \
     case "$target" in \
         xtensa-*) \
-            port=$(just _find_port "303a:1001" "1209:5741" "10c4:ea60"); \
+            port=$(just _find_port "303a:1001" "1209:5741" "10c4:ea60" "1a86:7522" "1a86:7523"); \
             if [ -n "$port" ]; then \
                 echo "Using $port"; \
                 espflash flash -p "$port" "{{builds_dir}}/donglora-{{board}}-v{{version}}.elf"; \
@@ -86,11 +80,12 @@ flash board:
         *) just _flash_uf2 {{board}} ;; \
     esac
 
-# Flash ARM board via debug probe (requires J-Link or similar)
-flash-probe board:
+# Flash ARM board via debug probe (requires J-Link or similar).
+# `extra_features` is passed through to the build.
+flash-probe board extra_features="":
     @just _ensure_tools
-    @just build {{board}} release
-    @read -r feat target chip <<< "$(just _info {{board}})"; \
+    @just build {{board}} release "{{extra_features}}"
+    @set -- $(just _info {{board}}); feat=$1; target=$2; chip=$3; \
     probe-rs run --chip $chip "{{builds_dir}}/donglora-{{board}}-v{{version}}.elf"
 
 # Show binary size for a release build
@@ -103,10 +98,7 @@ test:
 
 # Check for outdated dependencies
 outdated:
-    @# embassy-executor 0.10 renamed arch-* → platform-* features.
-    @# esp-rtos 0.2 still pins embassy-executor ^0.9, blocking the upgrade.
-    @# cargo-outdated crashes trying to resolve 0.10 with the old feature name.
-    cargo outdated --exclude embassy-executor
+    cargo outdated
 
 # ── Private helpers ───────────────────────────────────────────────────
 
@@ -115,40 +107,40 @@ outdated:
 _ensure_tools:
     @mise trust --yes . 2>/dev/null; mise install --quiet
 
-# Run a cargo command for a board.
-# Xtensa: nightly cargo + esp rustc (via RUSTC override) + -Zbuild-std=core
+# Run a cargo command for a board, optionally with extra Cargo features
+# (comma-separated, e.g. "debug-checkpoint").
+# Xtensa: esp toolchain (cargo + rustc + rust-src together) + -Zbuild-std=core
 [private]
-_cargo board cmd extra_args="":
+_cargo board cmd extra_args="" extra_features="":
     @just _ensure_tools
-    @read -r feat target chip <<< "$(just _info {{board}})"; \
-    env=""; extra=""; \
+    @set -- $(just _info {{board}}); feat=$1; target=$2; chip=$3; \
+    [ -n "{{extra_features}}" ] && feat="$feat,{{extra_features}}"; \
+    extra=""; buildstd=""; \
     case "$target" in xtensa-*) \
         just _require_esp_toolchain; \
         [ -f "$HOME/export-esp.sh" ] && . "$HOME/export-esp.sh"; \
-        env="RUSTC=$(rustup which rustc --toolchain esp)"; extra="+nightly"; buildstd="-Zbuild-std=core,alloc";; \
+        extra="+esp"; buildstd="-Zbuild-std=core,alloc";; \
     esac; \
-    eval $env cargo $extra {{cmd}} --target "$target" --features "$feat" $buildstd {{extra_args}}
+    cargo $extra {{cmd}} --target "$target" --features "$feat" $buildstd {{extra_args}}
 
 # Ensure a board's toolchain is available, auto-installing if needed
 [private]
 _can_build board:
-    @read -r feat target chip <<< "$(just _info {{board}})"; \
+    @set -- $(just _info {{board}}); feat=$1; target=$2; chip=$3; \
     case "$target" in \
         xtensa-*) just _require_esp_toolchain ;; \
         *) rustup target list --installed | grep -q "^$target$" || rustup target add "$target" ;; \
     esac
 
-# Ensure the ESP Xtensa toolchain is installed (espup installed via mise)
+# Ensure the ESP Xtensa toolchain is installed (espup installed via mise).
+# The esp toolchain ships with its own cargo, rustc, and rust-src — no extra
+# components are needed on top.
 [private]
 _require_esp_toolchain:
     @just _ensure_tools
     @if ! rustup toolchain list | grep -q "^esp"; then \
         echo "ESP toolchain not found, installing via espup (this may take a while)..." >&2; \
         espup install || { echo "error: espup install failed" >&2; exit 1; }; \
-    fi; \
-    if ! rustup component list --toolchain nightly --installed 2>/dev/null | grep -q "^rust-src"; then \
-        echo "Installing nightly rust-src (needed for -Zbuild-std)..." >&2; \
-        rustup component add rust-src --toolchain nightly || { echo "error: failed to install rust-src" >&2; exit 1; }; \
     fi
 
 # Find a serial port matching any of the given VID:PID pairs (checked in order)
@@ -170,15 +162,25 @@ _find_port +vid_pids:
 [private]
 _copy_firmware board profile:
     @mkdir -p {{builds_dir}}
-    @read -r feat target chip <<< "$(just _info {{board}})"; \
+    @set -- $(just _info {{board}}); feat=$1; target=$2; chip=$3; \
     src="target/$target/{{profile}}/donglora"; \
     dst="{{builds_dir}}/donglora-{{board}}-v{{version}}"; \
     if [ -f "$src" ]; then \
         cp "$src" "$dst.elf"; echo "→ $dst.elf"; \
         case "$target" in \
+            xtensa-*) \
+                espflash save-image --chip "$chip" --merge --skip-padding "$src" "$dst.bin"; \
+                echo "→ $dst.bin"; \
+                ;; \
+            thumbv6m-*) \
+                rust-objcopy -O ihex "$src" "$dst.hex"; \
+                cargo-hex-to-uf2 hex-to-uf2 --input-path "$dst.hex" --output-path "$dst.uf2" --family rp2040; \
+                rm "$dst.hex"; \
+                echo "→ $dst.uf2"; \
+                ;; \
             thumbv7em-*) \
-                mise exec -- rust-objcopy -O ihex "$src" "$dst.hex"; \
-                mise exec -- cargo-hex-to-uf2 hex-to-uf2 --input-path "$dst.hex" --output-path "$dst.uf2" --family nrf52840; \
+                rust-objcopy -O ihex "$src" "$dst.hex"; \
+                cargo-hex-to-uf2 hex-to-uf2 --input-path "$dst.hex" --output-path "$dst.uf2" --family nrf52840; \
                 rm "$dst.hex"; \
                 echo "→ $dst.uf2"; \
                 ;; \
@@ -201,11 +203,19 @@ _flash_uf2 board:
     sync; \
     echo "Done — board will reboot automatically"
 
+# Single source of truth for per-board metadata: "feature target chip".
+# ADD A NEW BOARD HERE and in the `boards` list near the top of this file.
 [private]
 _info name:
-    @if [ "{{name}}" == "heltec_v3" ]; then echo "{{heltec_v3}}"; \
-     elif [ "{{name}}" == "heltec_v3_uart" ]; then echo "{{heltec_v3_uart}}"; \
-     elif [ "{{name}}" == "heltec_v4" ]; then echo "{{heltec_v4}}"; \
-     elif [ "{{name}}" == "rak_wisblock_4631" ]; then echo "{{rak_wisblock_4631}}"; \
-     elif [ "{{name}}" == "wio_tracker_l1" ]; then echo "{{wio_tracker_l1}}"; \
-     else echo "Unknown board: {{name}}" >&2; exit 1; fi
+    @case "{{name}}" in \
+        heltec_v3)             echo "heltec_v3 xtensa-esp32s3-none-elf esp32s3" ;; \
+        heltec_v3_uart)        echo "heltec_v3_uart xtensa-esp32s3-none-elf esp32s3" ;; \
+        heltec_v4)             echo "heltec_v4 xtensa-esp32s3-none-elf esp32s3" ;; \
+        elecrow_thinknode_m2)  echo "elecrow_thinknode_m2 xtensa-esp32s3-none-elf esp32s3" ;; \
+        lilygo_tbeam)          echo "lilygo_tbeam xtensa-esp32-none-elf esp32" ;; \
+        lilygo_tbeam_supreme)  echo "lilygo_tbeam_supreme xtensa-esp32s3-none-elf esp32s3" ;; \
+        rak_wisblock_4631)     echo "rak_wisblock_4631 thumbv7em-none-eabihf nRF52840_xxAA" ;; \
+        waveshare_rp2040_lora) echo "waveshare_rp2040_lora thumbv6m-none-eabi rp2040" ;; \
+        wio_tracker_l1)        echo "wio_tracker_l1 thumbv7em-none-eabihf nRF52840_xxAA" ;; \
+        *) echo "Unknown board: {{name}}" >&2; exit 1 ;; \
+    esac

ld/rp2040-memory.x

@@ -0,0 +1,24 @@
+/* RP2040 memory layout — UF2 bootloader (ROM boot2)
+ *
+ *   0x10000000 – 0x10000100   boot2 (second-stage bootloader, 256 bytes)
+ *   0x10000100 – 0x10200000   Application  <- we live here
+ *
+ * Flash: 2MB (W25Q16JV on Waveshare RP2040-LoRa)
+ * RAM: 264KB SRAM (two 256KB banks + 2x 4KB scratch)
+ */
+
+MEMORY
+{
+  BOOT2 : ORIGIN = 0x10000000, LENGTH = 0x100
+  FLASH : ORIGIN = 0x10000100, LENGTH = 2048K - 0x100
+  RAM   : ORIGIN = 0x20000000, LENGTH = 264K
+}
+
+EXTERN(BOOT2_FIRMWARE)
+
+SECTIONS {
+    .boot2 ORIGIN(BOOT2) :
+    {
+        KEEP(*(.boot2));
+    } > BOOT2
+} INSERT BEFORE .text;

mise.toml

@@ -1,9 +1,24 @@
 [tools]
-rust = "1.93"
 just = "latest"
 
-"cargo:cargo-binutils" = "latest"   # `cargo size`, `cargo objdump`, etc.
-"cargo:cargo-hex-to-uf2" = "latest" # ELF → UF2 via Intel HEX for nRF52840 DFU
-"cargo:espup" = "0.16"
-"cargo:espflash" = "3"              # 4.x has broken nix dependency on current stable Rust
-"cargo:probe-rs-tools" = "0.31"
+# Cargo-installed tooling via mise's `cargo:` backend.
+"cargo:cargo-binutils" = "latest"   # rust-objcopy, rust-size
+"cargo:cargo-hex-to-uf2" = "latest" # ELF → UF2 for nRF52 / RP2040 DFU drives
+"cargo:espup" = "latest"            # bootstraps the ESP Xtensa toolchain
+"cargo:espflash" = "3"              # flash + save-image for ESP targets (4.x requires esp_app_desc!() in app — revisit alongside esp-hal 1.1+ / drop-the-patches cleanup)
+"cargo:probe-rs-tools" = "latest"   # debug-probe flash/run for ARM targets
+
+# Stable Rust + cross-compile targets. Targets land under $RUSTUP_HOME for
+# the pinned toolchain, so they're always available under `mise exec` — no
+# extra `rustup target add` step at setup time.
+#
+# Xtensa ESP targets are NOT listed here — they use the self-contained `esp`
+# toolchain installed out-of-band by `espup` (see `just setup`). That
+# toolchain ships its own rust-src for `-Zbuild-std`.
+#
+# profile = "minimal" (just rustc, rust-std, cargo), "default" (adds rust-docs, rustfmt, clippy)
+#
+[tools.rust]
+version = "1.94"
+profile = "default"
+targets = "thumbv6m-none-eabi,thumbv7em-none-eabihf"

src/board/PORTING.md

@@ -7,6 +7,7 @@
 Create `src/board/your_board.rs`. Use an existing board as a template:
 - ESP32-S3 boards: copy `heltec_v4.rs` (uses shared helpers from `board/esp32s3.rs` and `hal/esp32s3.rs`)
 - nRF52840 boards: copy `rak_wisblock_4631.rs` (uses shared helpers from `hal/nrf52840.rs`)
+- RP2040 boards: copy `waveshare_rp2040_lora.rs` (uses shared helpers from `hal/rp2040.rs`)
 - New MCU family: create a new `hal/<mcu>.rs` with MCU primitives first
 
 `build.rs` auto-discovers your board file — any `.rs` file in `src/board/` that

src/board/elecrow_thinknode_m2.rs

@@ -0,0 +1,141 @@
+//! ELECROW ThinkNode-M2 — ESP32-S3 Meshtastic handset with SH1106 OLED.
+//!
+//! Tamagotchi-form-factor handheld: ESP32-S3-WROOM-1-N4 + SX1262 + 1.3" SH1106
+//! OLED + WCH CH340K UART bridge + 1000 mAh Li-Po. Sold pre-loaded with
+//! Meshtastic; this firmware turns it into a DongLoRa radio bridge.
+//!
+//! Pin map (verified from Meshtastic's variants/esp32s3/ELECROW-ThinkNode-M2
+//! and PR meshtastic/firmware#6354):
+//!   LoRa SPI: SCK=12, MOSI=11, MISO=13, CS=10
+//!   LoRa ctl: RESET=21, BUSY=14, DIO1=3
+//!   LoRa pwr: GPIO48 (must be HIGH before any SPI traffic)
+//!   OLED:     I2C0 SDA=16, SCL=15, SH1106 @ 0x3C
+//!   VEXT:     GPIO46 (active HIGH — gates OLED supply)
+//!   UART:     TX=43, RX=44 via CH340K bridge (USB 1a86:7522)
+//!   LED:      GPIO6 (active HIGH indicator)
+//!
+//! Notable differences from the Heltec ESP32-S3 boards:
+//!   * Display is SH1106 (not SSD1306) — uses the existing sh1106 driver.
+//!   * VEXT_ENABLE polarity is reversed (active HIGH here, active LOW on Heltec).
+//!   * Dedicated LoRa power enable on GPIO48 — must be sequenced before SPI init.
+//!   * TCXO is driven at 3.3 V via DIO3 (Heltec uses 1.8 V).
+
+use esp_hal::gpio::{Level, Output, OutputConfig};
+
+use super::esp32s3;
+use super::traits::{BoardParts, LoRaBoard};
+use crate::driver::sh1106::Sh1106;
+use crate::driver::simple_led::SimpleLed;
+use crate::hal::esp32s3 as mcu;
+
+pub use super::esp32s3::{DisplayI2c, RadioDriver, RadioParts};
+
+// ── Concrete peripheral types ───────────────────────────────────────
+
+pub type DisplayDriver = Sh1106<DisplayI2c>;
+pub type UartDriver = esp_hal::uart::Uart<'static, esp_hal::Async>;
+pub type LedDriver = SimpleLed<Output<'static>>;
+
+// ── Peripheral bundles ──────────────────────────────────────────────
+
+pub struct UartParts {
+    pub driver: UartDriver,
+}
+
+pub struct DisplayParts {
+    pub i2c: DisplayI2c,
+}
+
+// ── Display init ────────────────────────────────────────────────────
+
+pub async fn create_display(i2c: DisplayI2c) -> Option<DisplayDriver> {
+    let mut display = Sh1106::new(i2c, 0x3C);
+
+    embassy_time::Timer::after_millis(100).await;
+    if display.init().await.is_err() {
+        defmt::error!("SH1106 display init failed");
+        return None;
+    }
+    let _ = display.set_brightness(0xFF).await;
+    Some(display)
+}
+
+// ── Board init ──────────────────────────────────────────────────────
+
+pub struct Board {
+    p: esp_hal::peripherals::Peripherals,
+}
+
+impl LoRaBoard for Board {
+    const NAME: &'static str = "ELECROW ThinkNode-M2";
+    const TX_POWER_RANGE: (i8, i8) = (-9, 22);
+
+    type RadioParts = RadioParts;
+    type CommParts = UartParts;
+    type DisplayParts = DisplayParts;
+    type DisplayDriver = DisplayDriver;
+    type LedDriver = LedDriver;
+
+    fn init() -> Self {
+        let p = esp_hal::init(esp_hal::Config::default());
+        Self { p }
+    }
+
+    fn mac_address() -> [u8; 6] {
+        mcu::mac_address()
+    }
+
+    fn into_parts(self) -> BoardParts<RadioParts, UartParts, DisplayParts, LedDriver> {
+        let p = self.p;
+
+        mcu::start_timer(p.TIMG0, p.SW_INTERRUPT);
+
+        // VEXT_ENABLE: GPIO46, active HIGH — powers OLED rail (opposite of Heltec).
+        // Output has no Drop impl, so the pin stays HIGH for program lifetime.
+        let _vext = Output::new(p.GPIO46, Level::High, OutputConfig::default());
+        esp_hal::delay::Delay::new().delay_millis(10);
+
+        // LORA_POWER_EN: GPIO48, active HIGH — must be HIGH before any SPI traffic.
+        let _lora_pwr = Output::new(p.GPIO48, Level::High, OutputConfig::default());
+        esp_hal::delay::Delay::new().delay_millis(10);
+
+        // SPI2 for SX1262: SCK=12, MOSI=11, MISO=13
+        let spi_bus = mcu::init_spi(p.SPI2, p.DMA_CH0, p.GPIO12, p.GPIO11, p.GPIO13);
+
+        // SX1262: CS=10, RESET=21, DIO1=3, BUSY=14, TCXO driven at 3.3 V via DIO3.
+        let radio = esp32s3::init_radio(
+            spi_bus,
+            p.GPIO10,
+            p.GPIO21,
+            p.GPIO3,
+            p.GPIO14,
+            lora_phy::sx126x::TcxoCtrlVoltage::Ctrl3V3,
+        );
+
+        // UART0 via CP2102 bridge: TX=43, RX=44
+        use esp_hal::uart::{Config as UartConfig, Uart};
+        let host = UartParts {
+            driver: Uart::new(p.UART0, UartConfig::default())
+                .expect("UART init")
+                .with_tx(p.GPIO43)
+                .with_rx(p.GPIO44)
+                .into_async(),
+        };
+
+        // I2C0 for SH1106 OLED: SDA=16, SCL=15
+        let i2c = mcu::init_i2c(p.I2C0, p.GPIO16, p.GPIO15);
+        let display = Some(DisplayParts { i2c });
+
+        // LED on GPIO6 (active HIGH)
+        let led_pin = Output::new(p.GPIO6, Level::Low, OutputConfig::default());
+        let led = SimpleLed(led_pin);
+
+        BoardParts {
+            radio,
+            host,
+            display,
+            led,
+            mac: Self::mac_address(),
+        }
+    }
+}

src/board/esp32.rs

@@ -0,0 +1,103 @@
+//! Shared types and peripheral wiring for classic-ESP32 SX1276 boards.
+//!
+//! Counterpart to `board::esp32s3` for the SX126x line. Builds an
+//! `Sx127x<Sx1276>` driver from an already-initialized SPI bus plus the
+//! board's reset and DIO0 pins. SX127x has no `BUSY` line — DIO0 carries
+//! every IRQ (TX done, RX done, header valid, …) and lora-phy's
+//! `GenericSx127xInterfaceVariant` waits on it directly.
+
+use embassy_embedded_hal::shared_bus::asynch::spi::SpiDevice;
+use embassy_sync::blocking_mutex::raw::NoopRawMutex;
+use embassy_time::Delay;
+use esp_hal::gpio::{Input, InputConfig, InputPin, Level, Output, OutputConfig, OutputPin, Pull};
+
+use lora_phy::iv::GenericSx127xInterfaceVariant;
+use lora_phy::sx127x::{self, Sx127x};
+
+use crate::hal::esp32 as mcu;
+
+// ── Re-export MCU types ─────────────────────────────────────────────
+
+pub use mcu::{I2cBus as DisplayI2c, SpiBus};
+
+// ── Concrete peripheral types ───────────────────────────────────────
+
+type Nss = Output<'static>;
+type Iv = GenericSx127xInterfaceVariant<Output<'static>, Input<'static>>;
+type RadioSpiDevice = SpiDevice<'static, NoopRawMutex, SpiBus, Nss>;
+pub type RadioDriver = Sx127x<RadioSpiDevice, Iv, sx127x::Sx1276>;
+
+// ── Peripheral bundles ──────────────────────────────────────────────
+
+pub struct RadioParts {
+    pub driver: RadioDriver,
+    pub delay: Delay,
+}
+
+pub struct DisplayParts {
+    pub i2c: DisplayI2c,
+}
+
+// ── Display driver ──────────────────────────────────────────────────
+
+pub type DisplayDriver = ssd1306::Ssd1306Async<
+    ssd1306::prelude::I2CInterface<DisplayI2c>,
+    ssd1306::size::DisplaySize128x64,
+    ssd1306::mode::BufferedGraphicsModeAsync<ssd1306::size::DisplaySize128x64>,
+>;
+
+/// Construct and initialize an SSD1306 display from raw I²C.
+pub async fn create_display(i2c: DisplayI2c) -> Option<DisplayDriver> {
+    use ssd1306::mode::DisplayConfigAsync;
+    use ssd1306::prelude::{Brightness, DisplayRotation};
+    use ssd1306::size::DisplaySize128x64;
+    use ssd1306::{I2CDisplayInterface, Ssd1306Async};
+
+    let interface = I2CDisplayInterface::new(i2c);
+    let mut display = Ssd1306Async::new(interface, DisplaySize128x64, DisplayRotation::Rotate0)
+        .into_buffered_graphics_mode();
+
+    embassy_time::Timer::after_millis(100).await;
+    if display.init().await.is_err() {
+        defmt::error!("SSD1306 display init failed");
+        return None;
+    }
+    let _ = display.set_brightness(Brightness::BRIGHTEST).await;
+    Some(display)
+}
+
+// ── Shared peripheral init helpers ──────────────────────────────────
+
+/// Construct an SX1276 radio from an initialized SPI bus.
+///
+/// `dio0` is the primary IRQ (TX/RX done). The SX1276 module on the T-Beam
+/// runs from a crystal oscillator, not a TCXO, and power comes from the
+/// AXP192's PA_BOOST rail — `tx_boost = true` routes TX through the PA
+/// output for +20 dBm.
+pub fn init_radio(
+    spi_bus: &'static embassy_sync::mutex::Mutex<NoopRawMutex, SpiBus>,
+    nss_pin: impl OutputPin + 'static,
+    reset_pin: impl OutputPin + 'static,
+    dio0_pin: impl InputPin + 'static,
+) -> RadioParts {
+    let nss = Output::new(nss_pin, Level::High, OutputConfig::default());
+    let spi_device = SpiDevice::new(spi_bus, nss);
+
+    let reset = Output::new(reset_pin, Level::High, OutputConfig::default());
+    let dio0 = Input::new(dio0_pin, InputConfig::default().with_pull(Pull::Down));
+
+    let iv =
+        GenericSx127xInterfaceVariant::new(reset, dio0, None, None).expect("SX1276 interface init");
+
+    let sx_config = sx127x::Config {
+        chip: sx127x::Sx1276,
+        tcxo_used: false,
+        tx_boost: true,
+        rx_boost: false,
+    };
+
+    RadioParts {
+        driver: Sx127x::new(spi_device, iv, sx_config),
+        delay: Delay,
+    }
+}

src/board/esp32s3.rs

@@ -7,7 +7,7 @@
 use embassy_embedded_hal::shared_bus::asynch::spi::SpiDevice;
 use embassy_sync::blocking_mutex::raw::NoopRawMutex;
 use embassy_time::Delay;
-use esp_hal::gpio::{Input, InputConfig, Level, Output, OutputConfig, Pull};
+use esp_hal::gpio::{Input, InputConfig, InputPin, Level, Output, OutputConfig, OutputPin, Pull};
 
 use lora_phy::iv::GenericSx126xInterfaceVariant;
 use lora_phy::sx126x::{self, Sx1262, Sx126x};
@@ -32,12 +32,25 @@ pub struct RadioParts {
     pub delay: Delay,
 }
 
+// SSD1306 display support is Heltec-specific. ESP32-S3 boards that use a
+// different controller (e.g. ThinkNode-M2 uses SH1106) provide their own
+// DisplayParts / DisplayDriver / create_display directly.
+#[cfg(any(
+    feature = "heltec_v3",
+    feature = "heltec_v3_uart",
+    feature = "heltec_v4"
+))]
 pub struct DisplayParts {
     pub i2c: DisplayI2c,
 }
 
 // ── Display driver ──────────────────────────────────────────────────
 
+#[cfg(any(
+    feature = "heltec_v3",
+    feature = "heltec_v3_uart",
+    feature = "heltec_v4"
+))]
 pub type DisplayDriver = ssd1306::Ssd1306Async<
     ssd1306::prelude::I2CInterface<DisplayI2c>,
     ssd1306::size::DisplaySize128x64,
@@ -45,6 +58,11 @@ pub type DisplayDriver = ssd1306::Ssd1306Async<
 >;
 
 /// Construct and initialize an SSD1306 display from raw I2C.
+#[cfg(any(
+    feature = "heltec_v3",
+    feature = "heltec_v3_uart",
+    feature = "heltec_v4"
+))]
 pub async fn create_display(i2c: DisplayI2c) -> Option<DisplayDriver> {
     use ssd1306::mode::DisplayConfigAsync;
     use ssd1306::prelude::{Brightness, DisplayRotation};
@@ -67,12 +85,17 @@ pub async fn create_display(i2c: DisplayI2c) -> Option<DisplayDriver> {
 // ── Shared peripheral init helpers ──────────────────────────────────
 
 /// Construct SX1262 radio from an initialized SPI bus.
+///
+/// Generic over GPIO type so boards with different radio pin assignments can
+/// share this helper. `tcxo_voltage` selects the DIO3-driven TCXO supply:
+/// Heltec boards use `Ctrl1V8`, the ELECROW ThinkNode-M2 uses `Ctrl3V3`, etc.
 pub fn init_radio(
     spi_bus: &'static embassy_sync::mutex::Mutex<NoopRawMutex, SpiBus>,
-    nss_pin: esp_hal::peripherals::GPIO8<'static>,
-    reset_pin: esp_hal::peripherals::GPIO12<'static>,
-    dio1_pin: esp_hal::peripherals::GPIO14<'static>,
-    busy_pin: esp_hal::peripherals::GPIO13<'static>,
+    nss_pin: impl OutputPin + 'static,
+    reset_pin: impl OutputPin + 'static,
+    dio1_pin: impl InputPin + 'static,
+    busy_pin: impl InputPin + 'static,
+    tcxo_voltage: sx126x::TcxoCtrlVoltage,
 ) -> RadioParts {
     let nss = Output::new(nss_pin, Level::High, OutputConfig::default());
     let spi_device = SpiDevice::new(spi_bus, nss);
@@ -86,7 +109,7 @@ pub fn init_radio(
 
     let sx_config = sx126x::Config {
         chip: Sx1262,
-        tcxo_ctrl: Some(sx126x::TcxoCtrlVoltage::Ctrl1V8),
+        tcxo_ctrl: Some(tcxo_voltage),
         use_dcdc: true,
         rx_boost: false,
     };

src/board/heltec_v3.rs

@@ -14,9 +14,7 @@ use super::traits::{BoardParts, LoRaBoard};
 use crate::driver::simple_led::SimpleLed;
 use crate::hal::esp32s3 as mcu;
 
-pub use super::esp32s3::{
-    create_display, DisplayDriver, DisplayParts, RadioDriver, RadioParts,
-};
+pub use super::esp32s3::{create_display, DisplayDriver, DisplayParts, RadioDriver, RadioParts};
 
 pub type UsbDriver = esp_hal::otg_fs::asynch::Driver<'static>;
 pub type LedDriver = SimpleLed<Output<'static>>;
@@ -51,14 +49,21 @@ impl LoRaBoard for Board {
     fn into_parts(self) -> BoardParts<RadioParts, UsbParts, DisplayParts, LedDriver> {
         let p = self.p;
 
-        mcu::start_timer(p.TIMG0);
+        mcu::start_timer(p.TIMG0, p.SW_INTERRUPT);
 
-        // Vext power: GPIO36, active LOW to enable peripherals
-        let vext = Output::new(p.GPIO36, Level::Low, OutputConfig::default());
-        core::mem::forget(vext);
+        // Vext power: GPIO36, active LOW to enable peripherals.
+        // Output has no Drop impl, so the pin stays configured for program lifetime.
+        let _vext = Output::new(p.GPIO36, Level::Low, OutputConfig::default());
 
         let spi_bus = mcu::init_spi(p.SPI2, p.DMA_CH0, p.GPIO9, p.GPIO10, p.GPIO11);
-        let radio = esp32s3::init_radio(spi_bus, p.GPIO8, p.GPIO12, p.GPIO14, p.GPIO13);
+        let radio = esp32s3::init_radio(
+            spi_bus,
+            p.GPIO8,
+            p.GPIO12,
+            p.GPIO14,
+            p.GPIO13,
+            lora_phy::sx126x::TcxoCtrlVoltage::Ctrl1V8,
+        );
 
         // Note: switches internal USB PHY from Serial-JTAG to OTG.
         let usb_inst = esp_hal::otg_fs::Usb::new(p.USB0, p.GPIO20, p.GPIO19);
@@ -72,12 +77,12 @@ impl LoRaBoard for Board {
             ),
         };
 
-        // SSD1306 display reset: pulse GPIO21 low->high before I2C init
+        // SSD1306 display reset: pulse GPIO21 low->high before I2C init.
+        // Output has no Drop impl; pin stays HIGH after this block.
         let mut display_rst = Output::new(p.GPIO21, Level::Low, OutputConfig::default());
         esp_hal::delay::Delay::new().delay_millis(10);
         display_rst.set_high();
         esp_hal::delay::Delay::new().delay_millis(10);
-        core::mem::forget(display_rst);
 
         let i2c = mcu::init_i2c(p.I2C0, p.GPIO17, p.GPIO18);
         let display = Some(DisplayParts { i2c });

src/board/heltec_v3_uart.rs

@@ -13,9 +13,7 @@ use super::traits::{BoardParts, LoRaBoard};
 use crate::driver::simple_led::SimpleLed;
 use crate::hal::esp32s3 as mcu;
 
-pub use super::esp32s3::{
-    create_display, DisplayDriver, DisplayParts, RadioDriver, RadioParts,
-};
+pub use super::esp32s3::{create_display, DisplayDriver, DisplayParts, RadioDriver, RadioParts};
 
 pub type UartDriver = esp_hal::uart::Uart<'static, esp_hal::Async>;
 pub type LedDriver = SimpleLed<Output<'static>>;
@@ -50,14 +48,21 @@ impl LoRaBoard for Board {
     fn into_parts(self) -> BoardParts<RadioParts, UartParts, DisplayParts, LedDriver> {
         let p = self.p;
 
-        mcu::start_timer(p.TIMG0);
+        mcu::start_timer(p.TIMG0, p.SW_INTERRUPT);
 
-        // Vext power: GPIO36, active LOW to enable peripherals
-        let vext = Output::new(p.GPIO36, Level::Low, OutputConfig::default());
-        core::mem::forget(vext);
+        // Vext power: GPIO36, active LOW to enable peripherals.
+        // Output has no Drop impl, so the pin stays configured for program lifetime.
+        let _vext = Output::new(p.GPIO36, Level::Low, OutputConfig::default());
 
         let spi_bus = mcu::init_spi(p.SPI2, p.DMA_CH0, p.GPIO9, p.GPIO10, p.GPIO11);
-        let radio = esp32s3::init_radio(spi_bus, p.GPIO8, p.GPIO12, p.GPIO14, p.GPIO13);
+        let radio = esp32s3::init_radio(
+            spi_bus,
+            p.GPIO8,
+            p.GPIO12,
+            p.GPIO14,
+            p.GPIO13,
+            lora_phy::sx126x::TcxoCtrlVoltage::Ctrl1V8,
+        );
 
         use esp_hal::uart::{Config as UartConfig, Uart};
         let host = UartParts {
@@ -68,12 +73,12 @@ impl LoRaBoard for Board {
                 .into_async(),
         };
 
-        // SSD1306 display reset: pulse GPIO21 low->high before I2C init
+        // SSD1306 display reset: pulse GPIO21 low->high before I2C init.
+        // Output has no Drop impl; pin stays HIGH after this block.
         let mut display_rst = Output::new(p.GPIO21, Level::Low, OutputConfig::default());
         esp_hal::delay::Delay::new().delay_millis(10);
         display_rst.set_high();
         esp_hal::delay::Delay::new().delay_millis(10);
-        core::mem::forget(display_rst);
 
         let i2c = mcu::init_i2c(p.I2C0, p.GPIO17, p.GPIO18);
         let display = Some(DisplayParts { i2c });

src/board/heltec_v4.rs

@@ -6,9 +6,7 @@ use super::traits::{BoardParts, LoRaBoard};
 use crate::driver::simple_led::SimpleLed;
 use crate::hal::esp32s3 as mcu;
 
-pub use super::esp32s3::{
-    create_display, DisplayDriver, DisplayParts, RadioDriver, RadioParts,
-};
+pub use super::esp32s3::{create_display, DisplayDriver, DisplayParts, RadioDriver, RadioParts};
 
 pub type UsbDriver = esp_hal::otg_fs::asynch::Driver<'static>;
 
@@ -44,14 +42,21 @@ impl LoRaBoard for Board {
     fn into_parts(self) -> BoardParts<RadioParts, UsbParts, DisplayParts, LedDriver> {
         let p = self.p;
 
-        mcu::start_timer(p.TIMG0);
+        mcu::start_timer(p.TIMG0, p.SW_INTERRUPT);
 
-        // Vext power: GPIO36, active LOW to enable peripherals
-        let vext = Output::new(p.GPIO36, Level::Low, OutputConfig::default());
-        core::mem::forget(vext);
+        // Vext power: GPIO36, active LOW to enable peripherals.
+        // Output has no Drop impl, so the pin stays configured for program lifetime.
+        let _vext = Output::new(p.GPIO36, Level::Low, OutputConfig::default());
 
         let spi_bus = mcu::init_spi(p.SPI2, p.DMA_CH0, p.GPIO9, p.GPIO10, p.GPIO11);
-        let radio = esp32s3::init_radio(spi_bus, p.GPIO8, p.GPIO12, p.GPIO14, p.GPIO13);
+        let radio = esp32s3::init_radio(
+            spi_bus,
+            p.GPIO8,
+            p.GPIO12,
+            p.GPIO14,
+            p.GPIO13,
+            lora_phy::sx126x::TcxoCtrlVoltage::Ctrl1V8,
+        );
 
         // Note: switches internal USB PHY from Serial-JTAG to OTG.
         let usb_inst = esp_hal::otg_fs::Usb::new(p.USB0, p.GPIO20, p.GPIO19);
@@ -65,12 +70,12 @@ impl LoRaBoard for Board {
             ),
         };
 
-        // SSD1315 display reset: pulse GPIO21 low->high before I2C init
+        // SSD1315 display reset: pulse GPIO21 low->high before I2C init.
+        // Output has no Drop impl; pin stays HIGH after this block.
         let mut display_rst = Output::new(p.GPIO21, Level::Low, OutputConfig::default());
         esp_hal::delay::Delay::new().delay_millis(10);
         display_rst.set_high();
         esp_hal::delay::Delay::new().delay_millis(10);
-        core::mem::forget(display_rst);
 
         let i2c = mcu::init_i2c(p.I2C0, p.GPIO17, p.GPIO18);
         let display = Some(DisplayParts { i2c });

src/board/lilygo_tbeam.rs

@@ -0,0 +1,140 @@
+//! LilyGo T-Beam (classic) — ESP32 + SX1276 + SSD1306 OLED + AXP192 PMIC.
+//!
+//! First-generation T-Beam. ESP32 (dual-core Xtensa LX6, no native USB),
+//! SX1276 module with XTAL (no TCXO), 128×64 SSD1306 OLED, AXP192 PMIC
+//! gating the LoRa and OLED rails, CP2102 USB-UART bridge for host I/O.
+//!
+//! The AXP192 shares an I²C bus with the OLED (SDA=21, SCL=22). PMIC init
+//! runs blocking on that bus first, then the same pins are re-initialized
+//! in async mode for the display task.
+//!
+//! Pin map (verified from MeshCore variants/lilygo_tbeam_SX1276/):
+//!   LoRa SPI:  SCK=5, MOSI=27, MISO=19, CS=18
+//!   LoRa ctl:  RESET=23, DIO0=26 (primary IRQ — SX127x has no BUSY)
+//!   OLED I²C:  SDA=21, SCL=22, SSD1306 @ 0x3C (shared with AXP192 @ 0x34)
+//!   UART host: TX=1, RX=3 via CP2102 bridge (USB 10c4:ea60)
+//!   LED:       GPIO4 (active LOW — red LED under the OLED, wrapped in
+//!              InvertedPin so SimpleLed sees normal polarity)
+//!
+//! GPS / battery / IMU / PCF8563 RTC are populated on the board but unused
+//! by this firmware.
+
+use esp_hal::gpio::{Level, Output, OutputConfig};
+use esp_hal::i2c::master::{Config as I2cConfig, I2c};
+
+use super::esp32;
+use super::traits::{BoardParts, LoRaBoard};
+use crate::driver::axp;
+use crate::driver::inverted_pin::InvertedPin;
+use crate::driver::simple_led::SimpleLed;
+use crate::hal::esp32 as mcu;
+use crate::protocol::RadioChipId;
+
+pub use super::esp32::{create_display, DisplayDriver, DisplayParts, RadioDriver, RadioParts};
+
+// ── Concrete peripheral types ───────────────────────────────────────
+
+pub type UartDriver = esp_hal::uart::Uart<'static, esp_hal::Async>;
+pub type LedDriver = SimpleLed<InvertedPin<Output<'static>>>;
+
+// ── Peripheral bundles ──────────────────────────────────────────────
+
+pub struct UartParts {
+    pub driver: UartDriver,
+}
+
+// ── Board init ──────────────────────────────────────────────────────
+
+pub struct Board {
+    p: esp_hal::peripherals::Peripherals,
+}
+
+impl LoRaBoard for Board {
+    const NAME: &'static str = "LilyGo T-Beam";
+    // SX1276 PA_BOOST range per the datasheet: +2 dBm min, +20 dBm max.
+    const TX_POWER_RANGE: (i8, i8) = (2, 20);
+
+    type RadioParts = RadioParts;
+    type CommParts = UartParts;
+    type DisplayParts = DisplayParts;
+    type DisplayDriver = DisplayDriver;
+    type LedDriver = LedDriver;
+
+    fn init() -> Self {
+        let p = esp_hal::init(esp_hal::Config::default());
+        Self { p }
+    }
+
+    fn mac_address() -> [u8; 6] {
+        mcu::mac_address()
+    }
+
+    fn radio_chip_id() -> u16 {
+        RadioChipId::Sx1276.as_u16()
+    }
+
+    fn freq_range_hz() -> (u32, u32) {
+        // SX1276 tuning window per datasheet (LF + HF bands combined).
+        (137_000_000, 1_020_000_000)
+    }
+
+    fn supported_sf_bitmap() -> u16 {
+        // SX127x supports SF6–SF12 (no SF5 like the SX126x).
+        0x1FC0
+    }
+
+    fn into_parts(self) -> BoardParts<RadioParts, UartParts, DisplayParts, LedDriver> {
+        let p = self.p;
+
+        mcu::start_timer(p.TIMG0, p.SW_INTERRUPT);
+
+        // AXP192 and SSD1306 share I²C0 (SDA=21, SCL=22). Build the bus
+        // once as blocking, drive the PMIC init, then convert to async for
+        // the display task — avoids re-consuming the I²C0 peripheral.
+        // PMIC failure isn't fatal to boot: log and proceed so the rest of
+        // the firmware can still emit diagnostics.
+        let mut i2c_blocking = I2c::new(p.I2C0, I2cConfig::default())
+            .expect("I2C0 init")
+            .with_sda(p.GPIO21)
+            .with_scl(p.GPIO22);
+        if let Err(_e) = axp::axp192_init_lora_oled(&mut i2c_blocking) {
+            defmt::error!("AXP192 init failed — LoRa rail may be dead");
+        }
+        // Let DCDC1 / LDO2 settle before SPI or display traffic.
+        esp_hal::delay::Delay::new().delay_millis(20);
+
+        // SPI2 for SX1276: SCK=5, MOSI=27, MISO=19
+        let spi_bus = mcu::init_spi(p.SPI2, p.DMA_SPI2, p.GPIO5, p.GPIO27, p.GPIO19);
+
+        // SX1276: CS=18, RESET=23, DIO0=26 (primary IRQ)
+        let radio = esp32::init_radio(spi_bus, p.GPIO18, p.GPIO23, p.GPIO26);
+
+        // UART0 via CP2102 bridge: TX=1, RX=3 (ESP32 default console)
+        use esp_hal::uart::{Config as UartConfig, Uart};
+        let host = UartParts {
+            driver: Uart::new(p.UART0, UartConfig::default())
+                .expect("UART init")
+                .with_tx(p.GPIO1)
+                .with_rx(p.GPIO3)
+                .into_async(),
+        };
+
+        // Hand the (now async) I²C bus to the SSD1306 display task.
+        let display = Some(DisplayParts {
+            i2c: i2c_blocking.into_async(),
+        });
+
+        // TX activity LED on GPIO4 (active LOW — pin idles HIGH = LED off).
+        // InvertedPin flips set_high/set_low so SimpleLed stays polarity-agnostic.
+        let led_pin = Output::new(p.GPIO4, Level::High, OutputConfig::default());
+        let led = SimpleLed(InvertedPin(led_pin));
+
+        BoardParts {
+            radio,
+            host,
+            display,
+            led,
+            mac: Self::mac_address(),
+        }
+    }
+}

src/board/lilygo_tbeam_supreme.rs

@@ -0,0 +1,153 @@
+//! LilyGo T-Beam S3 Supreme — ESP32-S3 + SX1262 + SH1106 OLED + AXP2101 PMIC.
+//!
+//! Big-brother of the classic T-Beam: ESP32-S3-WROOM-1 module, SX1262 with a
+//! TCXO, 128×64 SH1106 OLED, AXP2101 PMIC on a dedicated I²C1 bus. Native USB
+//! (no UART bridge chip).
+//!
+//! The AXP2101 gates power to the SX1262 and OLED. Without its init sequence
+//! the LoRa chip never responds on SPI and `LoRa::new` fails.
+//!
+//! Pin map (verified from MeshCore variants/lilygo_tbeam_supreme_SX1262/):
+//!   LoRa SPI: SCK=12, MOSI=11, MISO=13, CS=10
+//!   LoRa ctl: RESET=5, DIO1=1, BUSY=4 (TCXO @ 1.6 V via DIO3)
+//!   OLED I²C: SDA=17, SCL=18, SH1106 @ 0x3C (I²C0)
+//!   PMIC I²C: SDA=42, SCL=41, AXP2101 @ 0x34 (I²C1, blocking, PMIC-only)
+//!   USB:      native USB-C on GPIO19/20 (fixed ESP32-S3 D+/D-)
+//!   LED:      GPIO6 (active HIGH indicator, reuses MeshCore's P_LORA_TX_LED)
+//!
+//! GPS / battery / IMU / SD / BME280 are unused — DongLoRa is a transparent
+//! LoRa-over-USB bridge. The PMIC init only enables ALDO1 (OLED) and ALDO3
+//! (LoRa); other rails are left at their AXP2101 power-on defaults.
+
+use esp_hal::gpio::{Level, Output, OutputConfig};
+use esp_hal::i2c::master::{Config as I2cConfig, I2c};
+use static_cell::StaticCell;
+
+use super::esp32s3;
+use super::traits::{BoardParts, LoRaBoard};
+use crate::driver::axp;
+use crate::driver::sh1106::Sh1106;
+use crate::driver::simple_led::SimpleLed;
+use crate::hal::esp32s3 as mcu;
+
+pub use super::esp32s3::{DisplayI2c, RadioDriver, RadioParts};
+
+// ── Concrete peripheral types ───────────────────────────────────────
+
+pub type DisplayDriver = Sh1106<DisplayI2c>;
+pub type UsbDriver = esp_hal::otg_fs::asynch::Driver<'static>;
+pub type LedDriver = SimpleLed<Output<'static>>;
+
+// ── Peripheral bundles ──────────────────────────────────────────────
+
+pub struct UsbParts {
+    pub driver: UsbDriver,
+}
+
+pub struct DisplayParts {
+    pub i2c: DisplayI2c,
+}
+
+// ── Display init ────────────────────────────────────────────────────
+
+pub async fn create_display(i2c: DisplayI2c) -> Option<DisplayDriver> {
+    let mut display = Sh1106::new(i2c, 0x3C);
+
+    embassy_time::Timer::after_millis(100).await;
+    if display.init().await.is_err() {
+        defmt::error!("SH1106 display init failed");
+        return None;
+    }
+    let _ = display.set_brightness(0xFF).await;
+    Some(display)
+}
+
+// ── Board init ──────────────────────────────────────────────────────
+
+pub struct Board {
+    p: esp_hal::peripherals::Peripherals,
+}
+
+impl LoRaBoard for Board {
+    const NAME: &'static str = "LilyGo T-Beam S3 Supreme";
+    const TX_POWER_RANGE: (i8, i8) = (-9, 22);
+
+    type RadioParts = RadioParts;
+    type CommParts = UsbParts;
+    type DisplayParts = DisplayParts;
+    type DisplayDriver = DisplayDriver;
+    type LedDriver = LedDriver;
+
+    fn init() -> Self {
+        let p = esp_hal::init(esp_hal::Config::default());
+        Self { p }
+    }
+
+    fn mac_address() -> [u8; 6] {
+        mcu::mac_address()
+    }
+
+    fn into_parts(self) -> BoardParts<RadioParts, UsbParts, DisplayParts, LedDriver> {
+        let p = self.p;
+
+        mcu::start_timer(p.TIMG0, p.SW_INTERRUPT);
+
+        // AXP2101 PMIC on I²C1 (SDA=42, SCL=41). Blocking, one-shot: we only
+        // need to flip the LoRa/OLED rails on, then the bus can be dropped.
+        // If this fails the LoRa chip stays unpowered — log and keep going so
+        // the rest of the boot path can still produce diagnostics.
+        {
+            let mut pmic = I2c::new(p.I2C1, I2cConfig::default())
+                .expect("I2C1 init")
+                .with_sda(p.GPIO42)
+                .with_scl(p.GPIO41);
+            if let Err(_e) = axp::axp2101_init_lora_oled(&mut pmic) {
+                defmt::error!("AXP2101 init failed — LoRa rail may be dead");
+            }
+        }
+        // Let ALDO1/ALDO3 settle before touching the LoRa SPI or OLED I²C.
+        esp_hal::delay::Delay::new().delay_millis(20);
+
+        // SPI2 for SX1262: SCK=12, MOSI=11, MISO=13
+        let spi_bus = mcu::init_spi(p.SPI2, p.DMA_CH0, p.GPIO12, p.GPIO11, p.GPIO13);
+
+        // SX1262: CS=10, RESET=5, DIO1=1, BUSY=4, TCXO @ 1.6 V via DIO3.
+        let radio = esp32s3::init_radio(
+            spi_bus,
+            p.GPIO10,
+            p.GPIO5,
+            p.GPIO1,
+            p.GPIO4,
+            lora_phy::sx126x::TcxoCtrlVoltage::Ctrl1V6,
+        );
+
+        // Native USB-C on GPIO19/20. Switches the internal USB PHY from
+        // Serial-JTAG to OTG.
+        let usb_inst = esp_hal::otg_fs::Usb::new(p.USB0, p.GPIO20, p.GPIO19);
+        static EP_OUT_BUF: StaticCell<[u8; 1024]> = StaticCell::new();
+        let ep_out_buf = EP_OUT_BUF.init([0u8; 1024]);
+        let host = UsbParts {
+            driver: esp_hal::otg_fs::asynch::Driver::new(
+                usb_inst,
+                ep_out_buf,
+                esp_hal::otg_fs::asynch::Config::default(),
+            ),
+        };
+
+        // I2C0 for SH1106 OLED: SDA=17, SCL=18 (async, handed to display task).
+        let i2c = mcu::init_i2c(p.I2C0, p.GPIO17, p.GPIO18);
+        let display = Some(DisplayParts { i2c });
+
+        // Activity LED on GPIO6 (active HIGH).
+        let led_pin = Output::new(p.GPIO6, Level::Low, OutputConfig::default());
+        let led = SimpleLed(led_pin);
+
+        BoardParts {
+            radio,
+            host,
+            display,
+            led,
+            mac: Self::mac_address(),
+        }
+    }
+}

src/board/mod.rs.j2

@@ -3,7 +3,11 @@ pub mod traits;
 pub use traits::*;
 
 {% for helper, helper_features in helpers|items -%}
+{% if helper_features|length == 1 -%}
+#[cfg(feature = "{{ helper_features[0] }}")]
+{% else -%}
 #[cfg(any({% for f in helper_features %}feature = "{{ f }}"{% if not loop.last %}, {% endif %}{% endfor %}))]
+{% endif -%}
 mod {{ helper }};
 {% endfor %}
 cfg_if::cfg_if! {

src/board/rak_wisblock_4631.rs

@@ -20,7 +20,7 @@ type RadioSpiDevice = SpiDevice<'static, NoopRawMutex, mcu::SpiBus, Nss>;
 pub type RadioDriver = Sx126x<RadioSpiDevice, Iv, Sx1262>;
 pub type UsbDriver = mcu::UsbNrfDriver;
 pub type DisplayI2c = mcu::I2cBus;
-pub type LedDriver = ();
+pub type LedDriver = crate::driver::simple_led::SimpleLed<Output<'static>>;
 
 pub type DisplayDriver = ssd1306::Ssd1306Async<
     ssd1306::prelude::I2CInterface<DisplayI2c>,
@@ -78,10 +78,14 @@ impl LoRaBoard for Board {
     type CommParts = UsbParts;
     type DisplayParts = DisplayParts;
     type DisplayDriver = DisplayDriver;
-    type LedDriver = ();
+    type LedDriver = LedDriver;
 
     fn init() -> Self {
-        let p = embassy_nrf::init(Default::default());
+        // USB requires the 32 MHz HFXO (±50 ppm); the RC oscillator is out of spec.
+        let mut config = embassy_nrf::config::Config::default();
+        config.hfclk_source = embassy_nrf::config::HfclkSource::ExternalXtal;
+        config.lfclk_source = embassy_nrf::config::LfclkSource::ExternalXtal;
+        let p = embassy_nrf::init(config);
         Self { p }
     }
 
@@ -89,12 +93,18 @@ impl LoRaBoard for Board {
         mcu::mac_address()
     }
 
-    fn into_parts(self) -> BoardParts<RadioParts, UsbParts, DisplayParts, ()> {
+    fn into_parts(self) -> BoardParts<RadioParts, UsbParts, DisplayParts, LedDriver> {
         let p = self.p;
 
+        // SX1262 is power-gated on P1.05 — must be HIGH before any SPI access.
+        let sx_power_en = Output::new(p.P1_05, Level::High, OutputDrive::Standard);
+        core::mem::forget(sx_power_en);
+
         // ── SPI bus for SX1262 ──────────────────────────────────
         let mut spi_cfg = spim::Config::default();
         spi_cfg.frequency = spim::Frequency::M1;
+        // embassy_nrf::spim::Spim::new args: (spim, irq, sck, miso, mosi, config).
+        // Per RAK4631 BSP: SCK=P1.11, MISO=P1.13, MOSI=P1.12.
         let spi = Spim::new(p.SPI3, mcu::Irqs, p.P1_11, p.P1_13, p.P1_12, spi_cfg);
         let spi_bus = mcu::share_spi_bus(spi);
 
@@ -103,7 +113,11 @@ impl LoRaBoard for Board {
 
         let reset = Output::new(p.P1_06, Level::High, OutputDrive::Standard);
         let dio1 = Input::new(p.P1_15, Pull::Down);
-        let busy = Input::new(p.P1_14, Pull::Down);
+        // BUSY has an internal 20 kΩ pull-up on the SX1262 die (datasheet
+        // p. 53); an MCU-side Pull::Down fights it and leaves the line at
+        // an indeterminate voltage, making wait_on_busy unreliable. See
+        // lora-rs/lora-rs#260.
+        let busy = Input::new(p.P1_14, Pull::None);
 
         let iv = GenericSx126xInterfaceVariant::new(reset, dio1, busy, None, None)
             .expect("SX1262 interface init");
@@ -121,7 +135,9 @@ impl LoRaBoard for Board {
         };
 
         // ── USB ─────────────────────────────────────────────────
-        let vbus = mcu::alloc_vbus_detect(true, false);
+        // SoftwareVbusDetect(vbus_detected, power_ready). Mark both true so the
+        // driver doesn't block waiting for a power-ready signal we never raise.
+        let vbus = mcu::alloc_vbus_detect(true, true);
         let host = UsbParts {
             driver: Driver::new(p.USBD, mcu::Irqs, vbus),
         };
@@ -129,15 +145,24 @@ impl LoRaBoard for Board {
         // ── Display (optional RAK1921 SSD1306 OLED on I2C) ─────
         let twim_buf = mcu::alloc_i2c_buffer();
         let i2c = embassy_nrf::twim::Twim::new(
-            p.TWISPI0, mcu::Irqs, p.P0_13, p.P0_14, twim::Config::default(), twim_buf,
+            p.TWISPI0,
+            mcu::Irqs,
+            p.P0_13,
+            p.P0_14,
+            twim::Config::default(),
+            twim_buf,
         );
         let display = Some(DisplayParts { i2c });
 
+        // Green LED on P1.03 (RAK19007 Base, active HIGH).
+        let led_pin = Output::new(p.P1_03, Level::Low, OutputDrive::Standard);
+        let led = crate::driver::simple_led::SimpleLed(led_pin);
+
         BoardParts {
             radio,
             host,
             display,
-            led: (),
+            led,
             mac: Self::mac_address(),
         }
     }

src/board/traits.rs

@@ -9,6 +9,8 @@
 use embedded_graphics::draw_target::DrawTarget;
 use embedded_graphics::pixelcolor::BinaryColor;
 
+use crate::driver::DisplayBrightness;
+
 /// Async RGB LED control. Boards without an LED use `()` which is a no-op.
 pub trait RgbLed {
     fn set_rgb(&mut self, r: u8, g: u8, b: u8) -> impl core::future::Future<Output = ()>;
@@ -35,8 +37,9 @@ pub trait LoRaBoard: Sized {
     /// Display peripheral bundle (I2C bus for display init).
     type DisplayParts;
 
-    /// Concrete display driver type (must implement DrawTarget for rendering).
-    type DisplayDriver: DrawTarget<Color = BinaryColor>;
+    /// Concrete display driver type (must implement DrawTarget for rendering
+    /// and DisplayBrightness for the two-level dim control).
+    type DisplayDriver: DrawTarget<Color = BinaryColor> + DisplayBrightness;
 
     /// RGB LED driver. Boards without an LED use `()`.
     type LedDriver: RgbLed;
@@ -47,8 +50,40 @@ pub trait LoRaBoard: Sized {
     /// Read the board's unique hardware address (MAC, device ID, etc.).
     fn mac_address() -> [u8; 6];
 
+    /// Radio chip identifier reported in `GET_INFO`. Defaults to SX1262
+    /// (`0x0002`), matching every currently-supported board. Override for
+    /// boards that carry a different chip (LLCC68, SX1261, LR11xx, …).
+    fn radio_chip_id() -> u16 {
+        // SX1262 — see PROTOCOL.md §8.
+        0x0002
+    }
+
+    /// (freq_min_hz, freq_max_hz) — the RF front-end's effective tuning
+    /// window on this specific board. Reported in `GET_INFO`. Defaults
+    /// to the SX1262's nominal 150–960 MHz range.
+    fn freq_range_hz() -> (u32, u32) {
+        (150_000_000, 960_000_000)
+    }
+
+    /// Bitmap of supported LoRa spreading factors — bit N = SF N. Defaults
+    /// to SX126x's SF5–SF12 (`0x1FE0`). SX127x boards must override to
+    /// `0x1FC0` (SF6–SF12); LLCC68 boards to `0x0FE0` (SF5–SF11).
+    fn supported_sf_bitmap() -> u16 {
+        0x1FE0
+    }
+
+    /// Bitmap of supported LoRa bandwidths. Bit positions match
+    /// `LoRaBandwidth::as_u8()` (sub-GHz BW enum values 0..9). Defaults
+    /// to all sub-GHz BWs (`0x03FF`). SX128x boards flip the 2.4 GHz
+    /// bits when we add them.
+    fn supported_bw_bitmap() -> u16 {
+        0x03FF
+    }
+
     /// Decompose initialized board into peripheral bundles for each task.
-    fn into_parts(self) -> BoardParts<Self::RadioParts, Self::CommParts, Self::DisplayParts, Self::LedDriver>;
+    fn into_parts(
+        self,
+    ) -> BoardParts<Self::RadioParts, Self::CommParts, Self::DisplayParts, Self::LedDriver>;
 }
 
 /// Peripheral bundles for each firmware task, produced by [`LoRaBoard::into_parts`].

src/board/waveshare_rp2040_lora.rs

@@ -0,0 +1,150 @@
+use embassy_embedded_hal::shared_bus::asynch::spi::SpiDevice;
+use embassy_rp::gpio::{Input, Level, Output, Pull};
+use embassy_rp::spi;
+use embassy_sync::blocking_mutex::raw::NoopRawMutex;
+use embassy_time::Delay;
+
+use lora_phy::iv::GenericSx126xInterfaceVariant;
+use lora_phy::sx126x::{self, Sx1262, Sx126x};
+
+use super::traits::{BoardParts, LoRaBoard};
+use crate::hal::rp2040 as mcu;
+
+// ── Concrete peripheral types ──────────────────────────────────────
+
+type Nss = Output<'static>;
+type Iv = GenericSx126xInterfaceVariant<Output<'static>, Input<'static>>;
+type RadioSpiDevice = SpiDevice<'static, NoopRawMutex, mcu::SpiBus, Nss>;
+pub type RadioDriver = Sx126x<RadioSpiDevice, Iv, Sx1262>;
+pub type UsbDriver = mcu::UsbRpDriver;
+pub type LedDriver = crate::driver::simple_led::SimpleLed<Output<'static>>;
+
+// Display types — never instantiated (no OLED on this board), but the
+// trait requires concrete associated types that satisfy the bounds.
+pub type DisplayI2c =
+    embassy_rp::i2c::I2c<'static, embassy_rp::peripherals::I2C0, embassy_rp::i2c::Async>;
+pub type DisplayDriver = ssd1306::Ssd1306Async<
+    ssd1306::prelude::I2CInterface<DisplayI2c>,
+    ssd1306::size::DisplaySize128x64,
+    ssd1306::mode::BufferedGraphicsModeAsync<ssd1306::size::DisplaySize128x64>,
+>;
+
+// ── Peripheral bundles ─────────────────────────────────────────────
+
+pub struct RadioParts {
+    pub driver: RadioDriver,
+    pub delay: Delay,
+}
+
+pub struct UsbParts {
+    pub driver: UsbDriver,
+}
+
+pub struct DisplayParts {
+    pub i2c: DisplayI2c,
+}
+
+// ── Display init ───────────────────────────────────────────────────
+
+pub async fn create_display(_i2c: DisplayI2c) -> Option<DisplayDriver> {
+    None
+}
+
+// ── Board init ─────────────────────────────────────────────────────
+
+pub struct Board {
+    p: embassy_rp::Peripherals,
+}
+
+impl LoRaBoard for Board {
+    const NAME: &'static str = "Waveshare RP2040-LoRa";
+    const TX_POWER_RANGE: (i8, i8) = (-9, 22);
+
+    type RadioParts = RadioParts;
+    type CommParts = UsbParts;
+    type DisplayParts = DisplayParts;
+    type DisplayDriver = DisplayDriver;
+    type LedDriver = LedDriver;
+
+    fn init() -> Self {
+        let p = embassy_rp::init(Default::default());
+        Self { p }
+    }
+
+    fn mac_address() -> [u8; 6] {
+        mcu::mac_address()
+    }
+
+    fn into_parts(self) -> BoardParts<RadioParts, UsbParts, DisplayParts, LedDriver> {
+        let p = self.p;
+
+        // ── MAC address from flash unique ID ───────────────────
+        let mut flash =
+            embassy_rp::flash::Flash::<_, _, { 2 * 1024 * 1024 }>::new_blocking(p.FLASH);
+        mcu::init_mac(&mut flash);
+
+        // ── SPI1 bus for SX1262 ────────────────────────────────
+        //
+        // Pin mapping from Meshtastic & MeshCore firmware (confirmed working):
+        //   SCK = GPIO14, MOSI = GPIO15, MISO = GPIO24, CS = GPIO13
+        //
+        // The Waveshare wiki (https://www.waveshare.com/wiki/RP2040-LoRa) lists
+        // different pins (MOSI=11, MISO=8, CS=9) but those don't work in practice.
+        // Both sets are valid SPI1 alternate functions on RP2040.
+        let mut spi_cfg = spi::Config::default();
+        spi_cfg.frequency = 1_000_000;
+        let spi = spi::Spi::new(
+            p.SPI1,
+            p.PIN_14,
+            p.PIN_15,
+            p.PIN_24,
+            p.DMA_CH0,
+            p.DMA_CH1,
+            mcu::Irqs,
+            spi_cfg,
+        );
+        let spi_bus = mcu::share_spi_bus(spi);
+
+        let nss = Output::new(p.PIN_13, Level::High);
+        let spi_device = SpiDevice::new(spi_bus, nss);
+
+        let reset = Output::new(p.PIN_23, Level::High);
+        let dio1 = Input::new(p.PIN_16, Pull::Down);
+        let busy = Input::new(p.PIN_18, Pull::Down);
+
+        // PE4259 antenna switch: GPIO17 = !CTRL (rx_enable).
+        // DIO2 is internally wired as CTRL (tx_enable), managed by the SX1262.
+        let rx_enable = Output::new(p.PIN_17, Level::Low);
+        let iv = GenericSx126xInterfaceVariant::new(reset, dio1, busy, Some(rx_enable), None)
+            .expect("SX1262 interface init");
+
+        let sx_config = sx126x::Config {
+            chip: Sx1262,
+            tcxo_ctrl: None, // No TCXO on this board
+            use_dcdc: true,
+            rx_boost: false,
+        };
+
+        let radio = RadioParts {
+            driver: Sx126x::new(spi_device, iv, sx_config),
+            delay: Delay,
+        };
+
+        // ── USB ────────────────────────────────────────────────
+        let host = UsbParts {
+            driver: embassy_rp::usb::Driver::new(p.USB, mcu::Irqs),
+        };
+
+        // ── LED on GPIO25 ──────────────────────────────────────
+        let led_pin = Output::new(p.PIN_25, Level::Low);
+        let led = crate::driver::simple_led::SimpleLed(led_pin);
+
+        BoardParts {
+            radio,
+            host,
+            display: None,
+            led,
+            mac: Self::mac_address(),
+        }
+    }
+}

src/board/wio_tracker_l1.rs

@@ -96,7 +96,11 @@ impl LoRaBoard for Board {
 
         let reset = Output::new(p.P1_07, Level::High, OutputDrive::Standard);
         let dio1 = Input::new(p.P0_07, Pull::Down);
-        let busy = Input::new(p.P1_10, Pull::Down);
+        // BUSY has an internal 20 kΩ pull-up on the SX1262 die (datasheet
+        // p. 53); an MCU-side Pull::Down fights it and leaves the line at
+        // an indeterminate voltage, making wait_on_busy unreliable. See
+        // lora-rs/lora-rs#260.
+        let busy = Input::new(p.P1_10, Pull::None);
 
         // RF switch: RXEN on P1.08 (GPIO, toggled by lora_phy), TX via DIO2 (SX1262 internal).
         let rx_enable = Output::new(p.P1_08, Level::Low, OutputDrive::Standard);
@@ -128,7 +132,12 @@ impl LoRaBoard for Board {
         // ── Display (SH1106 OLED on I2C) ────────────────────────
         let twim_buf = mcu::alloc_i2c_buffer();
         let i2c = embassy_nrf::twim::Twim::new(
-            p.TWISPI0, mcu::Irqs, p.P0_06, p.P0_05, twim::Config::default(), twim_buf,
+            p.TWISPI0,
+            mcu::Irqs,
+            p.P0_06,
+            p.P0_05,
+            twim::Config::default(),
+            twim_buf,
         );
         let display = Some(DisplayParts { i2c });
 

src/channel.rs

@@ -1,67 +1,84 @@
-//! Inter-task communication channels.
+//! Inter-task communication channels for DongLoRa Protocol v2.
 //!
-//! Each channel connects exactly two tasks:
-//! - [`CommandChannel`]: USB → Radio (host commands)
-//! - [`ResponseChannel`]: Radio → USB (firmware responses)
-//! - [`DisplayCommandChannel`]: USB → Display (on/off/reset)
-//! - [`StatusWatch`]: Radio → Display (observable radio state)
+//! - [`CommandChannel`]: host_task → radio_task (tag-correlated commands)
+//! - [`OutboundChannel`]: radio_task → host_task (tag-correlated OK/ERR/TX_DONE
+//!   and tag-0 async RX/ERR events in one queue)
+//! - [`DisplayCommandChannel`]: host_task → display_task (internal only —
+//!   `On` on connect, `Reset` on disconnect; no longer driven from the wire)
+//! - [`RadioEventChannel`]: radio_task → display_task (typed mode/packet events)
 
 use embassy_sync::blocking_mutex::raw::CriticalSectionRawMutex;
 use embassy_sync::channel::Channel;
-use embassy_sync::watch::Watch;
 
-use crate::protocol::{Command, RadioConfig, Response};
+use crate::protocol::{Command, DeviceMessage, LoRaConfig};
 
-/// Display commands routed from host_task to display_task.
-#[derive(Debug, Clone, Copy, defmt::Format)]
-pub enum DisplayCommand {
-    On,
-    Off,
+// ── Host → Radio: tag-correlated commands ───────────────────────────
+
+/// An event flowing from the host task into the radio task.
+///
+/// `Command` carries a non-zero correlation tag (the host framing layer
+/// rejects tag=0 before it reaches here). `Reset` is a lifecycle signal
+/// from the host transport layer (DTR drop, UART teardown, or spec §3.4
+/// inactivity timeout) telling the radio to park back to Unconfigured
+/// and drain queues silently.
+#[allow(clippy::large_enum_variant)]
+#[derive(Debug, Clone)]
+pub enum InboundEvent {
+    Command { tag: u16, cmd: Command },
     Reset,
 }
 
-/// USB-to-display command channel (depth 4: display commands are rare events).
+/// Host-to-radio event channel (depth 8).
+pub type CommandChannel = Channel<CriticalSectionRawMutex, InboundEvent, 8>;
+
+// ── Radio → Host: OK / ERR / TX_DONE / RX / async ERR ──────────────
+
+/// One outbound D→H frame carrying its tag. Tag-correlated messages
+/// (OK, ERR in response, TX_DONE) carry the originating command's tag;
+/// async events (RX, async ERR) carry `tag = 0x0000`.
+#[derive(Debug, Clone)]
+pub struct OutboundFrame {
+    pub tag: u16,
+    pub msg: DeviceMessage,
+}
+
+/// Radio-to-host outbound channel (depth 32: enough to hold a burst of
+/// RX events + queued command responses without stalling the radio ISR).
+pub type OutboundChannel = Channel<CriticalSectionRawMutex, OutboundFrame, 32>;
+
+// ── Internal: display commands (no longer wire-visible) ────────────
+
+/// Internal display command routed from host_task to display_task. The
+/// wire protocol no longer carries DisplayOn/Off (`PROTOCOL.md §15.2`);
+/// these values drive the display statechart from local events only.
+#[derive(Debug, Clone, Copy, defmt::Format)]
+#[allow(dead_code)] // `Off` is reserved for future diagnostic paths.
+pub enum DisplayCommand {
+    /// Host connected (DTR rose on USB, or UART came up). Wake display.
+    On,
+    /// Host disconnected. Park display.
+    Off,
+    /// Reset cumulative counters (e.g., on config change).
+    Reset,
+}
+
+/// Host-to-display command channel.
 pub type DisplayCommandChannel = Channel<CriticalSectionRawMutex, DisplayCommand, 4>;
 
-/// Host-to-radio command channel (depth 16: buffer bursty host command sequences).
-pub type CommandChannel = Channel<CriticalSectionRawMutex, Command, 16>;
+// ── Radio → Display: typed packet/mode events ──────────────────────
 
-/// Radio-to-host response channel (depth 32: buffer RX packets while USB writes).
-pub type ResponseChannel = Channel<CriticalSectionRawMutex, Response, 32>;
-
-/// Observable radio status for the display task (2 receivers max).
-/// Display always sees the latest state — intermediate updates may be
-/// skipped, which is fine for a status display.
-pub type StatusWatch = Watch<CriticalSectionRawMutex, RadioStatus, 2>;
-
-/// Current radio state exposed to observers (e.g. display).
+/// Radio → downstream typed events. These drive the display; they are
+/// NOT the same thing as `OutboundFrame` (which goes out the host
+/// transport). Mode events describe what the radio is doing now; packet
+/// events describe what just happened.
 #[derive(Debug, Clone, defmt::Format)]
-pub struct RadioStatus {
-    pub state: RadioState,
-    pub config: Option<RadioConfig>,
-    pub rx_count: u32,
-    pub tx_count: u32,
-    pub last_rssi: Option<i16>,
-    pub last_snr: Option<i16>,
-}
-
-/// Radio state machine states.
-#[derive(Debug, Clone, Copy, PartialEq, Eq, defmt::Format)]
-pub enum RadioState {
+pub enum RadioEvent {
+    EnteredRx,
+    EnteredTx,
     Idle,
-    Receiving,
-    Transmitting,
+    PacketRx { rssi: i16, snr: Option<i16> },
+    PacketTx,
+    ConfigChanged(LoRaConfig),
 }
 
-impl Default for RadioStatus {
-    fn default() -> Self {
-        Self {
-            state: RadioState::Idle,
-            config: None,
-            rx_count: 0,
-            tx_count: 0,
-            last_rssi: None,
-            last_snr: None,
-        }
-    }
-}
+pub type RadioEventChannel = Channel<CriticalSectionRawMutex, RadioEvent, 32>;

src/debug_blink.rs

@@ -0,0 +1,230 @@
+//! LED-based diagnostic blinker (opt-in via the `debug-checkpoint` cargo
+//! feature).
+//!
+//! On boards whose UART is also the host protocol (heltec_v3_uart, any
+//! UART-only variant), defmt output would corrupt the COBS-framed host
+//! protocol. We can't use `defmt::info!` for live debugging on those
+//! boards while the host is connected. Instead we expose a single global
+//! atomic checkpoint; code sets it at interesting points in the boot /
+//! dispatch flow, and a dedicated task continuously flashes the board
+//! LED N times, pauses, and repeats — so a human can count the flashes
+//! and report "it got to N."
+//!
+//! Blink pattern:
+//! * Each flash: 400 ms ON, 400 ms OFF.
+//! * After N flashes: 2000 ms pause (LED held OFF).
+//! * Repeat indefinitely with the current `CHECKPOINT` value.
+//!
+//! Usage:
+//! ```ignore
+//! #[cfg(feature = "debug-checkpoint")]
+//! crate::debug_blink::set(3);  // "we reached checkpoint 3"
+//! ```
+//!
+//! The task replaces `display_task` when the `debug-checkpoint` feature is
+//! enabled — it takes the board LED and drives it exclusively.
+//!
+//! # Current checkpoint map
+//!
+//! Defined by the `crate::radio` module. Updated here any time the
+//! numbering changes there.
+//!
+//! | Flashes | Meaning                                                |
+//! |--------:|--------------------------------------------------------|
+//! |   1     | `radio_task` entered (pre-`LoRa::new`)                  |
+//! |   2     | `LoRa::new` succeeded                                   |
+//! |   3     | Machine constructed; about to enter `run()`             |
+//! |   4     | In `Idle` state                                         |
+//! |   5     | In `Receiving` state                                    |
+//! |   6     | TX phase 1: entered `perform_tx` (engages latch)        |
+//! |   7     | TX phase 2: in CAD                                      |
+//! |   8     | TX phase 3: in `prepare_for_tx`                         |
+//! |   9     | TX phase 4: awaiting `tx()`                             |
+//! |  10     | TX phase 5: `do_tx` returned OK                         |
+//! |  11     | TX phase 6: `respond_tx_done` handler entered           |
+//! |  12     | TX phase 7: `responses.send(TxDone)` returned           |
+//! |  13     | TX phase 8: `host_task` received the response from chan |
+//! |  14     | TX phase 9: `host_task` wrote response bytes to UART — TERMINAL SUCCESS |
+//! |  15     | TX errored somewhere — TERMINAL ERROR                   |
+//! |  16     | Boot error: `LoRa::new` failed                          |
+//! |  17     | Boot error: `start_rx` failed inside `start_rx_hw`      |
+//!
+//! # Latching
+//!
+//! * Latch engages **only** on `set(6)` (entry to `perform_tx`).
+//! * While latched, only TX-phase values (6–15) can update `CHECKPOINT`,
+//!   and only if strictly deeper than the current value.
+//! * Terminals (14 success, 15 error) freeze the latch until reboot.
+//! * `set(13)` and `set(14)` called from `host_task` are **no-ops before
+//!   the latch engages** — this prevents unrelated SetConfig/Ok responses
+//!   from polluting the display before any TX has happened.
+//!
+//! # Diagnostic logic
+//!
+//! If ai-bot reports a timeout but the LED shows:
+//! * **10** → `do_tx` ok, but `TransmitDone` event never dispatched.
+//! * **11** → handler entered, but `responses.send(...)` hung.
+//! * **12** → send pushed to channel, but `host_task` never picked it up.
+//! * **13** → `host_task` picked it up, but `tx.write_all` to UART hung.
+//! * **14** → full end-to-end firmware success. Hang is on the host side
+//!   of the UART (mux or wire).
+//! * **15** → TX errored somewhere along the way.
+//!
+//! # Building with the feature
+//!
+//! The `just` build/flash recipes pass a fixed feature list and don't
+//! surface an `extra-features` argument. To build a debug image:
+//!
+//! ```sh
+//! cd firmware
+//! . ~/export-esp.sh   # if building for xtensa (esp32s3)
+//! cargo +esp build --release \
+//!     --target xtensa-esp32s3-none-elf \
+//!     --features heltec_v3_uart,debug-checkpoint \
+//!     -Zbuild-std=core,alloc
+//! cp target/xtensa-esp32s3-none-elf/release/donglora \
+//!    builds/donglora-heltec_v3_uart-v$(sed -n 's/^version = "\(.*\)"/\1/p' \
+//!    Cargo.toml).elf
+//! espflash flash -p /dev/ttyUSB0 builds/donglora-heltec_v3_uart-v0.4.0.elf
+//! ```
+//!
+//! The normal `just flash heltec_v3_uart` command builds without the
+//! feature, so the debug code has zero footprint on release firmware.
+
+use core::sync::atomic::{AtomicBool, AtomicU8, Ordering};
+
+use embassy_executor::task;
+use embassy_time::{Duration, Timer};
+
+use crate::board::{LedDriver, RgbLed};
+
+/// Current diagnostic checkpoint — read by the blinker task. Zero means
+/// "no checkpoint set yet."
+///
+/// Write policy (see [`set`]): once a TX-phase value (6, 11, 12, 13) is
+/// stored, the latch engages and:
+/// * subsequent TX-phase writes update the value only if strictly deeper,
+/// * non-TX-phase writes (including the 7/10 terminal markers and the
+///   steady-state 4/5 post-TX writes) are **ignored** so the deepest phase
+///   reached on the FIRST TX attempt persists.
+///
+/// Rationale: a stuck-then-recovered TX attempt would normally flicker
+/// through the display too quickly to count. Latching preserves the
+/// evidence until reboot.
+pub static CHECKPOINT: AtomicU8 = AtomicU8::new(0);
+
+/// Has the TX-phase latch engaged yet? Written by [`set`], checked by
+/// [`set`]. Not intended for external inspection.
+static HAS_LATCHED: AtomicBool = AtomicBool::new(false);
+
+#[inline]
+fn is_host_phase(n: u8) -> bool {
+    // Values set only from `host_task` — meaningless before a TX has
+    // started, so we refuse to overwrite with them when the latch is
+    // not yet engaged.
+    n == 13 || n == 14
+}
+
+/// Ordered depth of each TX-related checkpoint. Returns `0` for values
+/// that are NOT TX phases (e.g. boot / steady-state / error indicators).
+///
+/// Value 18 ("next_command received CmdTransmit") is intentionally the
+/// SHALLOWEST TX phase — it fires before `perform_tx` entry (value 6)
+/// but is numerically higher because it was added last. The latch uses
+/// `phase_depth` rather than raw numeric comparison so 18 can engage
+/// the latch at depth 1 and later TX phases (6..=15) deepen over it.
+#[inline]
+fn phase_depth(n: u8) -> u8 {
+    match n {
+        18 => 1,  // pre-TX: CmdTransmit just read from commands channel
+        6 => 2,   // perform_tx entered
+        7 => 3,   // in CAD (before prepare_for_cad)
+        19 => 4,  // after prepare_for_cad (awaiting lora.cad IRQ)
+        8 => 5,   // in prepare_for_tx
+        9 => 6,   // in tx().await
+        10 => 7,  // do_tx returned Ok
+        11 => 8,  // respond_tx_done entered
+        12 => 9,  // respond_tx_done: responses.send returned
+        13 => 10, // host_task received response from channel
+        14 => 11, // host_task wrote response to UART (terminal success)
+        15 => 12, // TX errored (terminal error)
+        _ => 0,   // not a TX phase
+    }
+}
+
+#[inline]
+fn is_tx_phase(n: u8) -> bool {
+    phase_depth(n) > 0
+}
+
+#[inline]
+fn is_tx_terminal(n: u8) -> bool {
+    n == 14 || n == 15
+}
+
+/// Record that we reached checkpoint `n`. A no-op in terms of visible
+/// behavior unless the blinker task is spawned; the store itself is very
+/// cheap so leaving these calls in non-debug builds is harmless.
+///
+/// Latch semantics:
+/// * `set(18)` (CmdTransmit received by `next_command`) or `set(6)`
+///   (entry to `perform_tx`) engage the latch.
+/// * While latched, only strictly-deeper TX phases (by `phase_depth`)
+///   update the checkpoint.
+/// * Terminal values (14 success, 15 error) freeze the latch until
+///   reboot.
+/// * Host-phase values (13, 14) called from `host_task` are ignored
+///   before the latch engages, so unrelated `Response::Ok` writes from
+///   SetConfig don't pollute the LED reading before any TX.
+#[inline]
+pub fn set(n: u8) {
+    if HAS_LATCHED.load(Ordering::Relaxed) {
+        let cur = CHECKPOINT.load(Ordering::Relaxed);
+        if is_tx_terminal(cur) {
+            return;
+        }
+        if phase_depth(n) > phase_depth(cur) {
+            CHECKPOINT.store(n, Ordering::Relaxed);
+        }
+        return;
+    }
+
+    // Latch not yet engaged.
+    if is_host_phase(n) {
+        // `host_task` is draining the response channel before any TX —
+        // these values would be misleading. Skip them.
+        return;
+    }
+
+    CHECKPOINT.store(n, Ordering::Relaxed);
+    if is_tx_phase(n) {
+        HAS_LATCHED.store(true, Ordering::Relaxed);
+    }
+}
+
+/// Dedicated task that continuously flashes the LED to show the current
+/// checkpoint. Owns the board's LED driver exclusively — on boards where
+/// the display task would normally own the LED for RX/TX blips, spawn
+/// *either* this task *or* `display_task`, not both.
+#[task]
+pub async fn debug_blink_task(mut led: LedDriver) {
+    // Start with the LED off so the first flash is unambiguous.
+    led.set_rgb(0, 0, 0).await;
+
+    loop {
+        let n = CHECKPOINT.load(Ordering::Relaxed);
+        if n == 0 {
+            // No checkpoint yet — wait and re-check.
+            Timer::after(Duration::from_millis(200)).await;
+            continue;
+        }
+        for _ in 0..n {
+            led.set_rgb(255, 255, 255).await;
+            Timer::after(Duration::from_millis(400)).await;
+            led.set_rgb(0, 0, 0).await;
+            Timer::after(Duration::from_millis(400)).await;
+        }
+        // Long pause to separate cycles so the human can count.
+        Timer::after(Duration::from_millis(2000)).await;
+    }
+}

src/driver/axp.rs

@@ -0,0 +1,121 @@
+//! AXP PMIC init — turn on the rails that feed LoRa and the OLED.
+//!
+//! T-Beam–class boards gate LoRa, OLED (and GPS/sensors, which this firmware
+//! does not use) through an X-Powers PMIC on I²C. Until the PMIC is told to
+//! enable the right LDOs/DCDCs, the SX126x/SX127x chip sits unpowered and
+//! `LoRa::new` fails. This module's only job is to flip those switches.
+//!
+//! Two PMICs are covered:
+//!
+//! * [`axp2101_init_lora_oled`] — LilyGo T-Beam S3 Supreme. ALDO3 = 3.3 V
+//!   feeds the SX1262; ALDO1 = 3.3 V feeds the SH1106 OLED. Both live on a
+//!   dedicated I²C1 bus (separate from the display).
+//! * [`axp192_init_lora_oled`] — LilyGo T-Beam (classic). LDO2 = 3.3 V feeds
+//!   the SX1276; DCDC1 = 3.3 V feeds the SSD1306 OLED. PMIC shares the
+//!   display I²C bus.
+//!
+//! Everything unrelated to LoRa + OLED (GPS, sensors, SD, batt ADC) is left
+//! alone. Out-of-scope for a transparent LoRa-over-USB bridge.
+//!
+//! Init is blocking on purpose. It runs once during `into_parts`, which is a
+//! synchronous function called before task spawning. Using the blocking
+//! `embedded_hal` trait keeps the PMIC wiring out of the async machinery and
+//! lets the caller drop the I²C bus immediately after init (no bus handoff).
+
+use embedded_hal::i2c::I2c;
+
+/// Both chips respond at this 7-bit I²C address.
+const PMIC_ADDR: u8 = 0x34;
+
+// ── AXP2101 (T-Beam S3 Supreme) ──────────────────────────────────────
+
+#[cfg(feature = "lilygo_tbeam_supreme")]
+mod axp2101 {
+    use super::{I2c, PMIC_ADDR};
+
+    /// LDO on/off control register. Bits:
+    ///   0 = ALDO1, 1 = ALDO2, 2 = ALDO3, 3 = ALDO4, 4 = BLDO1, 5 = BLDO2.
+    const REG_LDO_ONOFF: u8 = 0x90;
+    /// ALDO1 voltage register (OLED rail on T-Beam Supreme).
+    const REG_ALDO1_V: u8 = 0x92;
+    /// ALDO3 voltage register (LoRa rail on T-Beam Supreme).
+    const REG_ALDO3_V: u8 = 0x94;
+
+    /// Voltage code for 3.3 V on ALDOx: 0.5 V + 28 × 100 mV.
+    const V_3V3: u8 = 28;
+
+    /// Mask enabling ALDO1 + ALDO3 in [`REG_LDO_ONOFF`].
+    const ALDO1_ALDO3: u8 = 0b0000_0101;
+
+    /// Bring up LoRa (ALDO3) and OLED (ALDO1) rails at 3.3 V.
+    ///
+    /// Voltage registers are set before the enable bits to avoid glitching
+    /// the rails through the reset-default voltage. Other rails are left
+    /// untouched (read-modify-write on the enable register) so any
+    /// board-specific OTP defaults stay intact.
+    pub fn init_lora_oled<I: I2c>(i2c: &mut I) -> Result<(), I::Error> {
+        i2c.write(PMIC_ADDR, &[REG_ALDO3_V, V_3V3])?;
+        i2c.write(PMIC_ADDR, &[REG_ALDO1_V, V_3V3])?;
+
+        let mut onoff = [0u8; 1];
+        i2c.write_read(PMIC_ADDR, &[REG_LDO_ONOFF], &mut onoff)?;
+        i2c.write(PMIC_ADDR, &[REG_LDO_ONOFF, onoff[0] | ALDO1_ALDO3])?;
+
+        Ok(())
+    }
+}
+
+#[cfg(feature = "lilygo_tbeam_supreme")]
+pub use axp2101::init_lora_oled as axp2101_init_lora_oled;
+
+// ── AXP192 (T-Beam classic) ──────────────────────────────────────────
+
+#[cfg(feature = "lilygo_tbeam")]
+mod axp192 {
+    use super::{I2c, PMIC_ADDR};
+
+    /// DCDC/LDO enable register. Bit layout:
+    ///   0 = DCDC1, 1 = DCDC3, 2 = LDO2, 3 = LDO3, 4 = DCDC2, 6 = EXTEN.
+    const REG_ONOFF: u8 = 0x12;
+    /// DCDC1 output voltage register (OLED rail on T-Beam classic).
+    /// 7-bit code, 25 mV step, 0.7 V offset → 3.3 V = 104 = `0x68`.
+    const REG_DCDC1_V: u8 = 0x26;
+    /// LDO2/LDO3 voltage register. Upper nibble = LDO2 (LoRa), lower nibble
+    /// = LDO3 (GPS). 100 mV step, 1.8 V offset → 3.3 V = 15 = `0xF`.
+    const REG_LDO23_V: u8 = 0x28;
+
+    /// DCDC1 code for 3.3 V.
+    const DCDC1_3V3: u8 = 0x68;
+    /// LDO2 nibble for 3.3 V in the upper half of [`REG_LDO23_V`].
+    const LDO2_3V3_UPPER: u8 = 0xF0;
+
+    /// Mask enabling DCDC1 + LDO2 in [`REG_ONOFF`].
+    const DCDC1_LDO2: u8 = 0b0000_0101;
+
+    /// Bring up LoRa (LDO2) and OLED (DCDC1) rails at 3.3 V on the
+    /// classic T-Beam's AXP192.
+    ///
+    /// GPS (LDO3) and EXTEN are not touched — this firmware has no GPS,
+    /// and any board-default for LDO3 voltage is preserved by
+    /// read-modify-write. Voltage is programmed before the enable bit
+    /// flips so the rail doesn't glitch through its reset default.
+    pub fn init_lora_oled<I: I2c>(i2c: &mut I) -> Result<(), I::Error> {
+        let mut ldo23 = [0u8; 1];
+        i2c.write_read(PMIC_ADDR, &[REG_LDO23_V], &mut ldo23)?;
+        i2c.write(
+            PMIC_ADDR,
+            &[REG_LDO23_V, (ldo23[0] & 0x0F) | LDO2_3V3_UPPER],
+        )?;
+
+        i2c.write(PMIC_ADDR, &[REG_DCDC1_V, DCDC1_3V3])?;
+
+        let mut onoff = [0u8; 1];
+        i2c.write_read(PMIC_ADDR, &[REG_ONOFF], &mut onoff)?;
+        i2c.write(PMIC_ADDR, &[REG_ONOFF, onoff[0] | DCDC1_LDO2])?;
+
+        Ok(())
+    }
+}
+
+#[cfg(feature = "lilygo_tbeam")]
+pub use axp192::init_lora_oled as axp192_init_lora_oled;

src/driver/inverted_pin.rs

@@ -0,0 +1,30 @@
+//! Generic `OutputPin` wrapper that inverts logic levels.
+//!
+//! When a peripheral is wired active-low (LED anode to V+, cathode to GPIO;
+//! reset line idle-high, etc.) the physical polarity is a property of the
+//! board, not of the driver. Wrapping the pin in `InvertedPin` lets drivers
+//! keep "set_high = assert" semantics while the board file expresses the
+//! wiring reality at construction time.
+//!
+//! ```ignore
+//! let pin = Output::new(p.GPIO4, Level::High, OutputConfig::default()); // off
+//! let led = SimpleLed(InvertedPin(pin)); // driver sees normal polarity
+//! ```
+
+use embedded_hal::digital::{ErrorType, OutputPin};
+
+pub struct InvertedPin<P>(pub P);
+
+impl<P: ErrorType> ErrorType for InvertedPin<P> {
+    type Error = P::Error;
+}
+
+impl<P: OutputPin> OutputPin for InvertedPin<P> {
+    fn set_low(&mut self) -> Result<(), Self::Error> {
+        self.0.set_high()
+    }
+
+    fn set_high(&mut self) -> Result<(), Self::Error> {
+        self.0.set_low()
+    }
+}

src/driver/mod.rs

@@ -1,5 +1,82 @@
-#[cfg(feature = "wio_tracker_l1")]
+#[cfg(any(
+    feature = "wio_tracker_l1",
+    feature = "elecrow_thinknode_m2",
+    feature = "lilygo_tbeam_supreme"
+))]
 pub mod sh1106;
 
-#[cfg(any(feature = "heltec_v3", feature = "heltec_v3_uart", feature = "heltec_v4", feature = "wio_tracker_l1"))]
+#[cfg(any(feature = "lilygo_tbeam_supreme", feature = "lilygo_tbeam"))]
+pub mod axp;
+
+#[cfg(feature = "lilygo_tbeam")]
+pub mod inverted_pin;
+
+#[cfg(any(
+    feature = "heltec_v3",
+    feature = "heltec_v3_uart",
+    feature = "heltec_v4",
+    feature = "elecrow_thinknode_m2",
+    feature = "lilygo_tbeam_supreme",
+    feature = "lilygo_tbeam",
+    feature = "rak_wisblock_4631",
+    feature = "wio_tracker_l1",
+    feature = "waveshare_rp2040_lora"
+))]
 pub mod simple_led;
+
+// ── Display brightness ────────────────────────────────────────────────
+//
+// The display statechart dims the OLED a few seconds after the last
+// activity. Our two driver families (`ssd1306` crate and our in-tree
+// `sh1106`) expose incompatible brightness APIs, so we wrap them in a
+// single async trait that the state-machine actions can call uniformly.
+
+/// Two-level backlight control used by the display dashboard.
+pub trait DisplayBrightness {
+    fn set_bright(&mut self) -> impl core::future::Future<Output = ()>;
+    fn set_dim(&mut self) -> impl core::future::Future<Output = ()>;
+}
+
+// Contrast values for the two brightness levels, picked to be common across
+// both driver families. `0xFF` is the SSD1306/SH1106 maximum; `0x08` is ~3%
+// of max — visible in a dim room, barely noticeable in daylight. Tune here.
+const CONTRAST_BRIGHT: u8 = 0xFF;
+const CONTRAST_DIM: u8 = 0x08;
+
+impl<DI, SIZE, MODE> DisplayBrightness for ssd1306::Ssd1306Async<DI, SIZE, MODE>
+where
+    DI: display_interface::AsyncWriteOnlyDataCommand,
+    SIZE: ssd1306::size::DisplaySizeAsync,
+{
+    async fn set_bright(&mut self) {
+        // `Brightness::custom(precharge, contrast)`. Matches the shape of
+        // the crate's BRIGHTEST preset (precharge 0x2) at max contrast.
+        let _ = self
+            .set_brightness(ssd1306::prelude::Brightness::custom(0x2, CONTRAST_BRIGHT))
+            .await;
+    }
+    async fn set_dim(&mut self) {
+        // Low precharge pairs with low contrast — same combination the
+        // crate's DIMMEST preset uses.
+        let _ = self
+            .set_brightness(ssd1306::prelude::Brightness::custom(0x1, CONTRAST_DIM))
+            .await;
+    }
+}
+
+#[cfg(any(
+    feature = "wio_tracker_l1",
+    feature = "elecrow_thinknode_m2",
+    feature = "lilygo_tbeam_supreme"
+))]
+impl<I> DisplayBrightness for sh1106::Sh1106<I>
+where
+    I: embedded_hal_async::i2c::I2c,
+{
+    async fn set_bright(&mut self) {
+        let _ = self.set_brightness(CONTRAST_BRIGHT).await;
+    }
+    async fn set_dim(&mut self) {
+        let _ = self.set_brightness(CONTRAST_DIM).await;
+    }
+}

src/driver/sh1106.rs

@@ -73,9 +73,9 @@ impl<I: I2c> Sh1106<I> {
         for page in 0..PAGES {
             // Set page address and column start (with SH1106 2-column offset).
             self.cmd(&[
-                0xB0 | page as u8,          // page address
-                COL_OFFSET & 0x0F, // column low nibble
-                0x10 | (COL_OFFSET >> 4),   // column high nibble
+                0xB0 | page as u8,        // page address
+                COL_OFFSET & 0x0F,        // column low nibble
+                0x10 | (COL_OFFSET >> 4), // column high nibble
             ])
             .await?;
 
@@ -90,7 +90,6 @@ impl<I: I2c> Sh1106<I> {
     pub async fn set_brightness(&mut self, value: u8) -> Result<(), I::Error> {
         self.cmd(&[0x81, value]).await
     }
-
 }
 
 impl<I: I2c> DrawTarget for Sh1106<I> {

src/hal/esp32.rs

@@ -0,0 +1,80 @@
+//! ESP32 (classic / non-S3) MCU initialization primitives.
+//!
+//! Mirror of `hal::esp32s3` with a single delta: the classic ESP32 uses a
+//! peripheral-bound DMA (`DMA_SPI2`) rather than the S3's channel-addressed
+//! GDMA (`DMA_CH0`). Timer, I²C, and eFuse access are otherwise identical
+//! between the two Xtensa parts in this esp-hal vintage.
+
+use embassy_sync::blocking_mutex::raw::NoopRawMutex;
+use esp_hal::dma::{DmaRxBuf, DmaTxBuf};
+use esp_hal::gpio::interconnect::{PeripheralInput, PeripheralOutput};
+use esp_hal::i2c::master::I2c;
+use esp_hal::spi::master::{Config as SpiConfig, Spi, SpiDmaBus};
+use esp_hal::spi::Mode as SpiMode;
+use esp_hal::time::Rate;
+use esp_hal::timer::timg::TimerGroup;
+use static_cell::StaticCell;
+
+// ── MCU-level types ─────────────────────────────────────────────────
+
+pub type SpiBus = SpiDmaBus<'static, esp_hal::Async>;
+pub type I2cBus = I2c<'static, esp_hal::Async>;
+
+// ── Timer ───────────────────────────────────────────────────────────
+
+/// Start the ESP-RTOS scheduler and Embassy time driver.
+pub fn start_timer(
+    timg0: esp_hal::peripherals::TIMG0<'static>,
+    sw_int: esp_hal::peripherals::SW_INTERRUPT<'static>,
+) {
+    let timg0 = TimerGroup::new(timg0);
+    let sw_ints = esp_hal::interrupt::software::SoftwareInterruptControl::new(sw_int);
+    esp_rtos::start(timg0.timer0, sw_ints.software_interrupt0);
+}
+
+// ── SPI bus ─────────────────────────────────────────────────────────
+
+/// Initialize SPI2 with peripheral-bound DMA and wrap in a shared bus
+/// (`StaticCell` + `Mutex`).
+///
+/// Generic over pin type. The classic ESP32's matrix of GPIO → peripheral
+/// routes lets any GPIO serve as any SPI signal — same as the S3.
+pub fn init_spi(
+    spi2: esp_hal::peripherals::SPI2<'static>,
+    dma_spi2: esp_hal::peripherals::DMA_SPI2<'static>,
+    sck: impl PeripheralOutput<'static>,
+    mosi: impl PeripheralOutput<'static>,
+    miso: impl PeripheralInput<'static>,
+) -> &'static embassy_sync::mutex::Mutex<NoopRawMutex, SpiBus> {
+    let spi = Spi::new(
+        spi2,
+        SpiConfig::default()
+            .with_frequency(Rate::from_mhz(1))
+            .with_mode(SpiMode::_0),
+    )
+    .expect("SPI init")
+    .with_sck(sck)
+    .with_mosi(mosi)
+    .with_miso(miso)
+    .with_dma(dma_spi2);
+
+    let (rx_buf, rx_desc, tx_buf, tx_desc) = esp_hal::dma_buffers!(256);
+    let dma_rx = DmaRxBuf::new(rx_desc, rx_buf).expect("DMA RX buf");
+    let dma_tx = DmaTxBuf::new(tx_desc, tx_buf).expect("DMA TX buf");
+
+    let spi = spi.with_buffers(dma_rx, dma_tx).into_async();
+
+    static SPI_BUS: StaticCell<embassy_sync::mutex::Mutex<NoopRawMutex, SpiBus>> =
+        StaticCell::new();
+    SPI_BUS.init(embassy_sync::mutex::Mutex::new(spi))
+}
+
+// ── MAC address ─────────────────────────────────────────────────────
+
+/// Read the factory-programmed MAC address from eFuse.
+pub fn mac_address() -> [u8; 6] {
+    esp_hal::efuse::base_mac_address()
+        .as_bytes()
+        .try_into()
+        .expect("MAC is 6 bytes")
+}

src/hal/esp32s3.rs

@@ -6,6 +6,7 @@
 
 use embassy_sync::blocking_mutex::raw::NoopRawMutex;
 use esp_hal::dma::{DmaRxBuf, DmaTxBuf};
+use esp_hal::gpio::interconnect::{PeripheralInput, PeripheralOutput};
 use esp_hal::i2c::master::{Config as I2cConfig, I2c};
 use esp_hal::spi::master::{Config as SpiConfig, Spi, SpiDmaBus};
 use esp_hal::spi::Mode as SpiMode;
@@ -21,20 +22,28 @@ pub type I2cBus = I2c<'static, esp_hal::Async>;
 // ── Timer ───────────────────────────────────────────────────────────
 
 /// Start the ESP-RTOS scheduler and Embassy time driver.
-pub fn start_timer(timg0: esp_hal::peripherals::TIMG0<'static>) {
+pub fn start_timer(
+    timg0: esp_hal::peripherals::TIMG0<'static>,
+    sw_int: esp_hal::peripherals::SW_INTERRUPT<'static>,
+) {
     let timg0 = TimerGroup::new(timg0);
-    esp_rtos::start(timg0.timer0);
+    let sw_ints = esp_hal::interrupt::software::SoftwareInterruptControl::new(sw_int);
+    esp_rtos::start(timg0.timer0, sw_ints.software_interrupt0);
 }
 
 // ── SPI bus ─────────────────────────────────────────────────────────
 
 /// Initialize SPI2 with DMA and wrap in a shared bus (StaticCell + Mutex).
+///
+/// Generic over pin type so boards with different SPI pin assignments can
+/// share this helper. Any GPIO that implements the esp-hal interconnect
+/// traits (which is every GPIO on the ESP32-S3) can be passed directly.
 pub fn init_spi(
     spi2: esp_hal::peripherals::SPI2<'static>,
     dma_ch0: esp_hal::peripherals::DMA_CH0<'static>,
-    sck: esp_hal::peripherals::GPIO9<'static>,
-    mosi: esp_hal::peripherals::GPIO10<'static>,
-    miso: esp_hal::peripherals::GPIO11<'static>,
+    sck: impl PeripheralOutput<'static>,
+    mosi: impl PeripheralOutput<'static>,
+    miso: impl PeripheralInput<'static>,
 ) -> &'static embassy_sync::mutex::Mutex<NoopRawMutex, SpiBus> {
     let spi = Spi::new(
         spi2,
@@ -62,10 +71,13 @@ pub fn init_spi(
 // ── I2C bus ─────────────────────────────────────────────────────────
 
 /// Initialize I2C0 for peripherals (display, sensors, etc.).
+///
+/// Generic over pin type. I2C lines are bidirectional (open-drain), so both
+/// `PeripheralInput` and `PeripheralOutput` bounds are required.
 pub fn init_i2c(
     i2c0: esp_hal::peripherals::I2C0<'static>,
-    sda: esp_hal::peripherals::GPIO17<'static>,
-    scl: esp_hal::peripherals::GPIO18<'static>,
+    sda: impl PeripheralInput<'static> + PeripheralOutput<'static>,
+    scl: impl PeripheralInput<'static> + PeripheralOutput<'static>,
 ) -> I2cBus {
     I2c::new(i2c0, I2cConfig::default())
         .expect("I2C init")
@@ -78,5 +90,8 @@ pub fn init_i2c(
 
 /// Read the factory-programmed MAC address from eFuse.
 pub fn mac_address() -> [u8; 6] {
-    esp_hal::efuse::Efuse::mac_address()
+    esp_hal::efuse::base_mac_address()
+        .as_bytes()
+        .try_into()
+        .expect("MAC is 6 bytes")
 }

src/hal/mod.rs

@@ -3,8 +3,20 @@
 //! Each submodule provides low-level bus and peripheral init for one MCU family.
 //! Board files call these with specific pins and construct higher-level drivers.
 
-#[cfg(any(feature = "heltec_v3", feature = "heltec_v3_uart", feature = "heltec_v4"))]
+#[cfg(any(
+    feature = "heltec_v3",
+    feature = "heltec_v3_uart",
+    feature = "heltec_v4",
+    feature = "elecrow_thinknode_m2",
+    feature = "lilygo_tbeam_supreme"
+))]
 pub mod esp32s3;
 
+#[cfg(feature = "lilygo_tbeam")]
+pub mod esp32;
+
 #[cfg(any(feature = "rak_wisblock_4631", feature = "wio_tracker_l1"))]
 pub mod nrf52840;
+
+#[cfg(feature = "waveshare_rp2040_lora")]
+pub mod rp2040;

src/hal/nrf52840.rs

@@ -25,9 +25,7 @@ pub type UsbNrfDriver =
 // ── SPI bus sharing ─────────────────────────────────────────────────
 
 /// Wrap an initialized SPI peripheral in a shared bus (StaticCell + Mutex).
-pub fn share_spi_bus(
-    spi: SpiBus,
-) -> &'static embassy_sync::mutex::Mutex<NoopRawMutex, SpiBus> {
+pub fn share_spi_bus(spi: SpiBus) -> &'static embassy_sync::mutex::Mutex<NoopRawMutex, SpiBus> {
     static SPI_BUS: StaticCell<embassy_sync::mutex::Mutex<NoopRawMutex, SpiBus>> =
         StaticCell::new();
     SPI_BUS.init(embassy_sync::mutex::Mutex::new(spi))

src/hal/rp2040.rs

@@ -0,0 +1,80 @@
+//! RP2040 MCU initialization primitives.
+//!
+//! Provides shared boilerplate for RP2040 boards: interrupt bindings,
+//! type aliases, StaticCell bus wrapping, USB init, and MAC address reading.
+
+use embassy_rp::bind_interrupts;
+use embassy_sync::blocking_mutex::raw::NoopRawMutex;
+use static_cell::StaticCell;
+
+// ── Interrupts (shared by all RP2040 boards) ──────────────────────
+
+bind_interrupts!(pub struct Irqs {
+    USBCTRL_IRQ => embassy_rp::usb::InterruptHandler<embassy_rp::peripherals::USB>;
+    DMA_IRQ_0 => embassy_rp::dma::InterruptHandler<embassy_rp::peripherals::DMA_CH0>,
+        embassy_rp::dma::InterruptHandler<embassy_rp::peripherals::DMA_CH1>;
+});
+
+// ── MCU-level types ────────────────────────────────────────────────
+
+pub type SpiBus =
+    embassy_rp::spi::Spi<'static, embassy_rp::peripherals::SPI1, embassy_rp::spi::Async>;
+pub type UsbRpDriver = embassy_rp::usb::Driver<'static, embassy_rp::peripherals::USB>;
+
+// ── SPI bus sharing ────────────────────────────────────────────────
+
+/// Wrap an initialized SPI peripheral in a shared bus (StaticCell + Mutex).
+pub fn share_spi_bus(spi: SpiBus) -> &'static embassy_sync::mutex::Mutex<NoopRawMutex, SpiBus> {
+    static SPI_BUS: StaticCell<embassy_sync::mutex::Mutex<NoopRawMutex, SpiBus>> =
+        StaticCell::new();
+    SPI_BUS.init(embassy_sync::mutex::Mutex::new(spi))
+}
+
+// ── MAC address ────────────────────────────────────────────────────
+
+/// Store for the MAC address derived from flash unique ID.
+/// Populated once during `init_mac()`, read by `mac_address()`.
+static MAC: StaticCell<[u8; 6]> = StaticCell::new();
+static mut MAC_REF: Option<&'static [u8; 6]> = None;
+
+/// Read the flash chip's unique ID and derive a 6-byte MAC address.
+///
+/// Must be called once during board init before `mac_address()`.
+pub fn init_mac<const FLASH_SIZE: usize>(
+    flash: &mut embassy_rp::flash::Flash<
+        '_,
+        embassy_rp::peripherals::FLASH,
+        embassy_rp::flash::Blocking,
+        FLASH_SIZE,
+    >,
+) {
+    let mut uid = [0u8; 8];
+    flash.blocking_unique_id(&mut uid).expect("flash unique ID");
+
+    // XOR the first 2 bytes into bytes 2..8 to fold 8 bytes into 6,
+    // then set the locally-administered bit (byte 0, bit 1).
+    let mac = [
+        uid[2] ^ uid[0] | 0x02,
+        uid[3] ^ uid[1],
+        uid[4],
+        uid[5],
+        uid[6],
+        uid[7],
+    ];
+
+    let stored = MAC.init(mac);
+    // SAFETY: Written once during single-threaded init, before the executor
+    // starts. All subsequent reads are from &'static reference.
+    unsafe {
+        MAC_REF = Some(stored);
+    }
+}
+
+/// Return the MAC address derived from the flash unique ID.
+///
+/// Panics if `init_mac()` has not been called.
+pub fn mac_address() -> [u8; 6] {
+    // SAFETY: MAC_REF is set once during init before the executor starts,
+    // and only read (never written) after that.
+    unsafe { *MAC_REF.expect("init_mac() must be called before mac_address()") }
+}

src/host/framing.rs

@@ -1,124 +1,121 @@
-//! Shared COBS protocol helpers for USB and UART transports.
+//! Shared framing helpers for USB and UART host transports.
 //!
-//! Both `usb_task` and `uart_task` use these helpers for frame
-//! accumulation, response encoding, and command routing.
+//! Ingress path: raw bytes → `FrameDecoder` → `(type_id, tag, payload)`
+//! → `Command::parse` → forwarded to radio task along with the tag. On
+//! parse failure we echo `ERR(ELENGTH/EPARAM/EMODULATION/EUNKNOWN_CMD)`
+//! with the received tag. On CRC/COBS failure we emit async
+//! `ERR(EFRAME)` with tag `0x0000` (`PROTOCOL.md §2.5`).
+//!
+//! Egress path: `OutboundFrame` (tag + DeviceMessage) → `encode_frame`
+//! → bytes ready for transport-level write.
 
 use defmt::warn;
 
-use crate::channel::{CommandChannel, DisplayCommand, DisplayCommandChannel, ResponseChannel};
-use crate::protocol::{Command, ErrorCode, Response};
+use crate::channel::{CommandChannel, InboundEvent, OutboundChannel, OutboundFrame};
+use crate::protocol::{
+    encode_frame, Command, CommandParseError, DeviceMessage, ErrorCode, FrameEncodeError,
+    MAX_PAYLOAD_FIELD, MAX_WIRE_FRAME,
+};
 
-/// Maximum COBS frame size (bytes).
-pub const MAX_FRAME: usize = 512;
-
-// Worst case: tag(1) + rssi(2) + snr(2) + len(2) + payload(256) = 263 bytes.
-// COBS adds ceil(263/254)+1 = 3 bytes. 266 < 512. Plenty of room.
-const _: () = assert!(
-    MAX_FRAME >= crate::protocol::MAX_PAYLOAD + 64,
-    "MAX_FRAME too small for max payload + COBS overhead"
-);
-
-/// Decodes COBS-framed commands from a byte stream.
-pub struct CobsDecoder {
-    buf: [u8; MAX_FRAME],
-    len: usize,
-}
-
-impl CobsDecoder {
-    pub const fn new() -> Self {
-        Self {
-            buf: [0u8; MAX_FRAME],
-            len: 0,
-        }
-    }
-
-    /// Reset the accumulator (discard partial frame).
-    pub fn reset(&mut self) {
-        self.len = 0;
-    }
-
-    /// Feed a chunk of bytes, calling `on_command` for each decoded command.
-    pub fn feed(&mut self, data: &[u8], mut on_command: impl FnMut(Command)) {
-        for &byte in data {
-            if byte == 0x00 {
-                // End of COBS frame — decode and dispatch
-                if self.len > 0 {
-                    let mut decode_buf = [0u8; MAX_FRAME];
-                    if let Some(decoded_len) =
-                        ucobs::decode(&self.buf[..self.len], &mut decode_buf)
-                    {
-                        if let Some(cmd) = Command::from_bytes(&decode_buf[..decoded_len]) {
-                            on_command(cmd);
-                        }
-                    }
-                }
-                self.len = 0;
-            } else if self.len < MAX_FRAME {
-                self.buf[self.len] = byte;
-                self.len += 1;
-            } else {
-                // Frame too large — discard
-                self.len = 0;
-            }
-        }
-    }
-}
-
-/// COBS-encode a response into `encode_buf` with trailing 0x00 sentinel.
+/// Dispatch a frame-level decode into the appropriate downstream queue.
 ///
-/// Returns the slice to send (encoded frame + sentinel), or `None` on overflow.
-pub fn cobs_encode_response<'a>(
-    response: Response,
-    write_buf: &mut [u8; MAX_FRAME],
-    encode_buf: &'a mut [u8; MAX_FRAME],
-) -> Option<&'a [u8]> {
-    let raw_len = response.write_to(write_buf);
-    let encoded_len = ucobs::encode(&write_buf[..raw_len], encode_buf).unwrap_or(0);
-    if encoded_len < encode_buf.len() {
-        encode_buf[encoded_len] = 0x00;
-        Some(&encode_buf[..encoded_len + 1])
-    } else {
-        warn!("COBS encode buffer overflow");
-        None
-    }
-}
-
-/// Route a parsed command to the appropriate handler.
-///
-/// Display and MAC commands are handled locally (response sent immediately).
-/// All other commands are forwarded to the radio task (response sent later).
-/// Both paths feed the same `ResponseChannel`, so the one-outstanding-command
-/// rule in PROTOCOL.md is required to keep solicited responses ordered.
-pub async fn route_command(
-    cmd: Command,
+/// - `type_id`, `tag`, and `payload` come from `FrameDecoder`.
+/// - Known commands are forwarded to the radio task via `commands`.
+/// - Parse failures produce a synchronous `ERR` with the echoed tag on
+///   `outbound`, so the host sees a concrete answer instead of timing out.
+/// - The caller is responsible for rejecting `tag == 0` before calling
+///   this; the spec says hosts MUST NOT send tag 0, and we classify such
+///   frames as framing errors upstream.
+pub async fn dispatch_frame(
+    type_id: u8,
+    tag: u16,
+    payload: &[u8],
     commands: &CommandChannel,
-    responses: &ResponseChannel,
-    display_commands: &DisplayCommandChannel,
-    has_display: bool,
-    mac: [u8; 6],
+    outbound: &OutboundChannel,
 ) {
-    match cmd {
-        Command::DisplayOn => {
-            if has_display {
-                display_commands.send(DisplayCommand::On).await;
-                responses.send(Response::Ok).await;
-            } else {
-                responses.send(Response::Error(ErrorCode::NoDisplay)).await;
+    if tag == 0 {
+        // Hosts MUST NOT use tag 0 on outbound commands. Treat as
+        // framing error; do not route to radio. (Spec §2.2)
+        emit_async_err(outbound, ErrorCode::EFrame).await;
+        return;
+    }
+    match Command::parse(type_id, payload) {
+        Ok(cmd) => {
+            let envelope = InboundEvent::Command { tag, cmd };
+            if commands.try_send(envelope).is_err() {
+                emit_sync_err(outbound, tag, ErrorCode::EBusy).await;
             }
         }
-        Command::DisplayOff => {
-            if has_display {
-                display_commands.send(DisplayCommand::Off).await;
-                responses.send(Response::Ok).await;
-            } else {
-                responses.send(Response::Error(ErrorCode::NoDisplay)).await;
-            }
-        }
-        Command::GetMac => {
-            responses.send(Response::MacAddress(mac)).await;
-        }
-        other => {
-            commands.send(other).await;
+        Err(e) => {
+            let code = parse_err_to_wire_code(e);
+            emit_sync_err(outbound, tag, code).await;
+        }
+    }
+}
+
+/// Emit an async framing error (tag = 0x0000) per spec §2.5.
+pub async fn emit_async_err(outbound: &OutboundChannel, code: ErrorCode) {
+    let frame = OutboundFrame {
+        tag: 0,
+        msg: DeviceMessage::Err(code),
+    };
+    if outbound.try_send(frame).is_err() {
+        warn!("async ERR dropped: outbound queue full");
+    }
+}
+
+/// Emit a synchronous error response echoing the originating tag.
+async fn emit_sync_err(outbound: &OutboundChannel, tag: u16, code: ErrorCode) {
+    let frame = OutboundFrame {
+        tag,
+        msg: DeviceMessage::Err(code),
+    };
+    if outbound.try_send(frame).is_err() {
+        warn!("sync ERR dropped: outbound queue full");
+    }
+}
+
+fn parse_err_to_wire_code(e: CommandParseError) -> ErrorCode {
+    match e {
+        CommandParseError::UnknownType => ErrorCode::EUnknownCmd,
+        CommandParseError::WrongLength => ErrorCode::ELength,
+        CommandParseError::InvalidField => ErrorCode::EParam,
+        CommandParseError::ReservedBitSet => ErrorCode::EParam,
+        CommandParseError::UnknownModulation => ErrorCode::EModulation,
+    }
+}
+
+/// Encode an outbound frame into a single wire-ready byte buffer.
+///
+/// Returns the number of bytes written to `out`, or `None` on buffer
+/// overflow / encode failure (caller may log and drop).
+pub fn encode_outbound(frame: &OutboundFrame, out: &mut [u8; MAX_WIRE_FRAME]) -> Option<usize> {
+    let mut payload_buf = [0u8; MAX_PAYLOAD_FIELD];
+    let payload_len = match frame.msg.encode_payload(&mut payload_buf) {
+        Ok(n) => n,
+        Err(e) => {
+            warn!("encode_payload failed: {:?}", defmt::Debug2Format(&e));
+            return None;
+        }
+    };
+    match encode_frame(
+        frame.msg.type_id(),
+        frame.tag,
+        &payload_buf[..payload_len],
+        out.as_mut_slice(),
+    ) {
+        Ok(n) => Some(n),
+        Err(FrameEncodeError::BufferTooSmall) => {
+            warn!("encode_frame: output buffer too small");
+            None
+        }
+        Err(FrameEncodeError::PayloadTooLarge) => {
+            warn!("encode_frame: payload exceeds MAX_PAYLOAD_FIELD");
+            None
+        }
+        Err(FrameEncodeError::CobsEncode) => {
+            warn!("encode_frame: COBS encode refused");
+            None
         }
     }
 }

src/host/mod.rs

@@ -6,7 +6,11 @@
 pub mod framing;
 
 cfg_if::cfg_if! {
-    if #[cfg(feature = "heltec_v3_uart")] {
+    if #[cfg(any(
+        feature = "heltec_v3_uart",
+        feature = "elecrow_thinknode_m2",
+        feature = "lilygo_tbeam"
+    ))] {
         mod uart;
         pub use uart::host_task;
     } else {

src/host/uart.rs

@@ -1,75 +1,141 @@
-//! UART host task: COBS-framed fixed-size LE command/response protocol.
+//! UART host task for DongLoRa Protocol v2.
 //!
-//! Used for boards with USB-UART bridge chips (e.g. CP2102 on Heltec V3).
+//! UART has no DTR line, so we assume a host is always present and
+//! rely entirely on the spec §3.4 inactivity watchdog (1 s of silence
+//! → Disconnected → drop radio to Unconfigured).
 
 use defmt::warn;
 use embassy_executor::task;
+use embassy_time::{Duration, Instant};
 use embedded_io_async::Write;
 
-use crate::channel::{CommandChannel, DisplayCommand, DisplayCommandChannel, ResponseChannel};
-use super::framing::{self, CobsDecoder, MAX_FRAME};
+use super::framing::{dispatch_frame, emit_async_err, encode_outbound};
+use crate::channel::{
+    CommandChannel, DisplayCommand, DisplayCommandChannel, InboundEvent, OutboundChannel,
+};
+use crate::protocol::{ErrorCode, FrameDecoder, FrameResult, MAX_PAYLOAD_FIELD, MAX_WIRE_FRAME};
+
+const READ_BUF: usize = 64;
+const INACTIVITY_MS: u64 = 1000;
 
 #[task]
 pub async fn host_task(
     parts: crate::board::UartParts,
     commands: &'static CommandChannel,
-    responses: &'static ResponseChannel,
+    outbound: &'static OutboundChannel,
     display_commands: &'static DisplayCommandChannel,
     has_display: bool,
-    mac: [u8; 6],
+    _mac: [u8; 6],
 ) {
     let (mut rx, mut tx) = parts.driver.split();
 
-    // UART has no DTR — signal the display that a host is present at boot.
+    // UART has no DTR — wake display immediately and assume a host.
     if has_display {
-        display_commands.send(DisplayCommand::Reset).await;
+        display_commands.send(DisplayCommand::On).await;
     }
 
-    let mut read_buf = [0u8; 64];
-    let mut write_buf = [0u8; MAX_FRAME];
-    let mut cobs_encode_buf = [0u8; MAX_FRAME];
-    let mut decoder = CobsDecoder::new();
+    let mut read_buf = [0u8; READ_BUF];
+    let mut write_buf: [u8; MAX_WIRE_FRAME] = [0u8; MAX_WIRE_FRAME];
+    let mut decoder = FrameDecoder::new();
+    let mut last_frame_at = Instant::now();
+    let mut connected = true;
 
     loop {
-        use embassy_futures::select::{select, Either};
+        use embassy_futures::select::{select3, Either3};
 
-        match select(
+        match select3(
             embedded_io_async::Read::read(&mut rx, &mut read_buf),
-            responses.receive(),
+            outbound.receive(),
+            embassy_time::Timer::after(Duration::from_millis(100)),
         )
         .await
         {
-            Either::First(result) => {
-                let n = match result {
-                    Ok(0) => continue,
-                    Ok(n) => n,
-                    Err(_) => {
-                        decoder.reset();
-                        embassy_time::Timer::after_millis(100).await;
-                        continue;
+            Either3::First(result) => match result {
+                Ok(0) => continue,
+                Ok(n) => {
+                    last_frame_at = Instant::now();
+                    if !connected {
+                        if has_display {
+                            let _ = display_commands.try_send(DisplayCommand::On);
+                        }
+                        connected = true;
+                    }
+                    dispatch_bytes(&mut decoder, &read_buf[..n], commands, outbound).await;
+                }
+                Err(_) => {
+                    decoder.reset();
+                    embassy_time::Timer::after_millis(100).await;
+                }
+            },
+            Either3::Second(frame) => {
+                if let Some(n) = encode_outbound(&frame, &mut write_buf) {
+                    if tx.write_all(&write_buf[..n]).await.is_err() {
+                        warn!("UART write failed, frame dropped");
                     }
-                };
-
-                let mut cmds = heapless::Vec::<_, 4>::new();
-                decoder.feed(&read_buf[..n], |cmd| {
-                    let _ = cmds.push(cmd);
-                });
-                for cmd in cmds {
-                    framing::route_command(
-                        cmd, commands, responses, display_commands, has_display, mac,
-                    )
-                    .await;
                 }
             }
-            Either::Second(response) => {
-                if let Some(frame) =
-                    framing::cobs_encode_response(response, &mut write_buf, &mut cobs_encode_buf)
-                {
-                    if tx.write_all(frame).await.is_err() {
-                        warn!("UART write failed, response dropped");
-                    }
-                }
+            Either3::Third(()) => {}
+        }
+
+        // Inactivity watchdog.
+        if connected && last_frame_at.elapsed() >= Duration::from_millis(INACTIVITY_MS) {
+            warn!("UART host inactivity timeout fired");
+            let _ = commands.try_send(InboundEvent::Reset);
+            if has_display {
+                let _ = display_commands.try_send(DisplayCommand::Reset);
+            }
+            connected = false;
+        }
+    }
+}
+
+async fn dispatch_bytes(
+    decoder: &mut FrameDecoder,
+    bytes: &[u8],
+    commands: &'static CommandChannel,
+    outbound: &'static OutboundChannel,
+) {
+    let mut work: heapless::Vec<FrameWork, 4> = heapless::Vec::new();
+    decoder.feed(bytes, |res| match res {
+        FrameResult::Ok {
+            type_id,
+            tag,
+            payload,
+        } => {
+            let mut p: heapless::Vec<u8, MAX_PAYLOAD_FIELD> = heapless::Vec::new();
+            let _ = p.extend_from_slice(payload);
+            let _ = work.push(FrameWork::Ok {
+                type_id,
+                tag,
+                payload: p,
+            });
+        }
+        FrameResult::Err(_) => {
+            let _ = work.push(FrameWork::Frame);
+        }
+    });
+    for w in work {
+        match w {
+            FrameWork::Ok {
+                type_id,
+                tag,
+                payload,
+            } => {
+                dispatch_frame(type_id, tag, &payload, commands, outbound).await;
+            }
+            FrameWork::Frame => {
+                emit_async_err(outbound, ErrorCode::EFrame).await;
             }
         }
     }
 }
+
+#[allow(clippy::large_enum_variant)]
+enum FrameWork {
+    Ok {
+        type_id: u8,
+        tag: u16,
+        payload: heapless::Vec<u8, MAX_PAYLOAD_FIELD>,
+    },
+    Frame,
+}

src/host/usb.rs

@@ -1,22 +1,117 @@
-//! USB CDC-ACM host task: COBS-framed fixed-size LE command/response protocol.
+//! USB CDC-ACM host task for DongLoRa Protocol v2.
+//!
+//! ```text
+//! Host
+//! ├── Disconnected   (default)   no DTR, or inactivity timer fired
+//! └── Connected                  host attached, liveness OK
+//!     entry: wake_display, start_liveness_timer
+//!     exit:  reset_radio, reset_display, stop_liveness_timer
+//! ```
+//!
+//! The statechart tracks one state bit: "is a host present?". DTR drives
+//! connect edges; the 1-second inactivity watchdog (spec §3.4) drives
+//! the disconnect edge when DTR is held high but no bytes arrive.
+//!
+//! The data plane (frame decode, command dispatch, frame encode) stays
+//! imperative in `protocol_loop` for the same reason the radio's
+//! `rx_once` stayed out of its chart: `read_packet` blocks.
 
 use defmt::warn;
 use embassy_executor::task;
 use embassy_futures::join::join;
+use embassy_time::{Duration, Instant};
 use embassy_usb::class::cdc_acm::{CdcAcmClass, Receiver, Sender, State};
 use embassy_usb::Builder;
+use hsmc::{statechart, Duration as HsmcDuration};
 use static_cell::StaticCell;
 
-use crate::channel::{CommandChannel, DisplayCommand, DisplayCommandChannel, ResponseChannel};
-use super::framing::{self, CobsDecoder, MAX_FRAME};
+use super::framing::{dispatch_frame, emit_async_err, encode_outbound};
+use crate::channel::{
+    CommandChannel, DisplayCommand, DisplayCommandChannel, InboundEvent, OutboundChannel,
+};
+use crate::protocol::{ErrorCode, FrameDecoder, FrameResult, MAX_WIRE_FRAME};
 
-const MAX_PACKET: usize = 64;
+const MAX_USB_PACKET: usize = 64;
+
+/// Spec §3.4: inactivity timer period. The device must see at least one
+/// frame (good or bad) every 1000 ms or the session is considered lost.
+const INACTIVITY_MS: u64 = 1000;
+
+/// Poll interval for the DTR edge detector / inactivity check.
+const POLL_INTERVAL_MS: u64 = 100;
+
+#[derive(Debug, Clone)]
+pub enum HostInput {
+    DtrRaised,
+    DtrDropped,
+    /// Host went silent for >1 s; kick the radio back to Unconfigured.
+    InactivityTimeout,
+}
+
+pub struct HostContext {
+    commands: &'static CommandChannel,
+    display_commands: &'static DisplayCommandChannel,
+    has_display: bool,
+}
+
+impl HostContext {
+    async fn wake_display_if_present(&self) {
+        if self.has_display {
+            self.display_commands.send(DisplayCommand::On).await;
+        }
+    }
+
+    async fn reset_display_if_present(&self) {
+        if self.has_display {
+            self.display_commands.send(DisplayCommand::Reset).await;
+        }
+    }
+
+    fn send_radio_reset(&self) {
+        if self.commands.try_send(InboundEvent::Reset).is_err() {
+            warn!("radio Reset inject: command queue full");
+        }
+    }
+}
+
+statechart! {
+    Host {
+        context: HostContext;
+        events: HostInput;
+        default(Disconnected);
+
+        state Disconnected {
+            on(DtrRaised) => Connected;
+        }
+
+        state Connected {
+            entry: wake_display;
+            exit: reset_radio, reset_display;
+            on(DtrDropped) => Disconnected;
+            on(InactivityTimeout) => Disconnected;
+        }
+    }
+}
+
+impl HostActions for HostActionContext<'_> {
+    async fn wake_display(&mut self) {
+        self.wake_display_if_present().await;
+    }
+
+    async fn reset_radio(&mut self) {
+        self.send_radio_reset();
+    }
+
+    async fn reset_display(&mut self) {
+        self.reset_display_if_present().await;
+    }
+}
 
 #[task]
 pub async fn host_task(
     parts: crate::board::UsbParts,
     commands: &'static CommandChannel,
-    responses: &'static ResponseChannel,
+    outbound: &'static OutboundChannel,
     display_commands: &'static DisplayCommandChannel,
     has_display: bool,
     mac: [u8; 6],
@@ -52,13 +147,20 @@ pub async fn host_task(
 
     let mut builder = Builder::new(parts.driver, config, desc_buf, conf_buf, bos_buf, ctrl_buf);
 
-    let class = CdcAcmClass::new(&mut builder, cdc_state, MAX_PACKET as u16);
+    let class = CdcAcmClass::new(&mut builder, cdc_state, MAX_USB_PACKET as u16);
     let mut usb_dev = builder.build();
     let (sender, receiver) = class.split();
 
     join(
         usb_dev.run(),
-        protocol_loop(sender, receiver, commands, responses, display_commands, has_display, mac),
+        protocol_loop(
+            sender,
+            receiver,
+            commands,
+            outbound,
+            display_commands,
+            has_display,
+        ),
     )
     .await;
 }
@@ -67,56 +169,47 @@ async fn protocol_loop<'d, D: embassy_usb_driver::Driver<'d>>(
     mut sender: Sender<'d, D>,
     mut receiver: Receiver<'d, D>,
     commands: &'static CommandChannel,
-    responses: &'static ResponseChannel,
+    outbound: &'static OutboundChannel,
     display_commands: &'static DisplayCommandChannel,
     has_display: bool,
-    mac: [u8; 6],
 ) {
     use embassy_futures::select::{select3, Either3};
 
-    let mut read_buf = [0u8; MAX_PACKET];
-    let mut write_buf = [0u8; MAX_FRAME];
-    let mut cobs_encode_buf = [0u8; MAX_FRAME];
-    let mut decoder = CobsDecoder::new();
-    let mut was_connected = false;
+    let mut machine = Host::new_local(HostContext {
+        commands,
+        display_commands,
+        has_display,
+    });
+    machine.step(HsmcDuration::ZERO).await;
+
+    let mut read_buf = [0u8; MAX_USB_PACKET];
+    let mut write_buf: [u8; MAX_WIRE_FRAME] = [0u8; MAX_WIRE_FRAME];
+    let mut decoder = FrameDecoder::new();
+
+    let mut last_frame_at = Instant::now();
 
     loop {
         match select3(
             receiver.read_packet(&mut read_buf),
-            responses.receive(),
-            embassy_time::Timer::after_millis(250),
+            outbound.receive(),
+            embassy_time::Timer::after(Duration::from_millis(POLL_INTERVAL_MS)),
         )
         .await
         {
-            Either3::First(result) => {
-                let n = match result {
-                    Ok(0) => continue,
-                    Ok(n) => n,
-                    Err(_) => {
-                        decoder.reset();
-                        embassy_time::Timer::after_millis(100).await;
-                        continue;
-                    }
-                };
-
-                let mut cmds = heapless::Vec::<_, 4>::new();
-                decoder.feed(&read_buf[..n], |cmd| {
-                    let _ = cmds.push(cmd);
-                });
-                for cmd in cmds {
-                    framing::route_command(
-                        cmd, commands, responses, display_commands, has_display, mac,
-                    )
-                    .await;
-                }
+            Either3::First(Ok(0)) => {}
+            Either3::First(Ok(n)) => {
+                last_frame_at = Instant::now();
+                dispatch_bytes(&mut decoder, &read_buf[..n], commands, outbound).await;
             }
-            Either3::Second(response) => {
-                if let Some(frame) =
-                    framing::cobs_encode_response(response, &mut write_buf, &mut cobs_encode_buf)
-                {
-                    for chunk in frame.chunks(MAX_PACKET) {
+            Either3::First(Err(_)) => {
+                decoder.reset();
+                embassy_time::Timer::after_millis(100).await;
+            }
+            Either3::Second(frame) => {
+                if let Some(n) = encode_outbound(&frame, &mut write_buf) {
+                    for chunk in write_buf[..n].chunks(MAX_USB_PACKET) {
                         if sender.write_packet(chunk).await.is_err() {
-                            warn!("USB write failed, response dropped");
+                            warn!("USB write failed, frame dropped");
                             break;
                         }
                     }
@@ -125,13 +218,90 @@ async fn protocol_loop<'d, D: embassy_usb_driver::Driver<'d>>(
             Either3::Third(()) => {}
         }
 
+        // DTR edge detection — drives Connected / Disconnected transitions.
         let connected = receiver.dtr();
-        if was_connected && !connected && has_display {
-            display_commands.send(DisplayCommand::Reset).await;
+        let was_connected = matches!(machine.current_state(), HostState::Connected);
+        match (was_connected, connected) {
+            (false, true) => {
+                let _ = machine.dispatch(HostInput::DtrRaised).await;
+                last_frame_at = Instant::now();
+            }
+            (true, false) => {
+                decoder.reset();
+                let _ = machine.dispatch(HostInput::DtrDropped).await;
+            }
+            _ => {}
         }
-        if !was_connected && connected && has_display {
-            display_commands.send(DisplayCommand::On).await;
+
+        // Inactivity watchdog (spec §3.4): while Connected, if no frame
+        // arrived in the last INACTIVITY_MS, drive the session back to
+        // Disconnected.
+        if matches!(machine.current_state(), HostState::Connected)
+            && last_frame_at.elapsed() >= Duration::from_millis(INACTIVITY_MS)
+        {
+            warn!("host inactivity timeout fired");
+            let _ = machine.dispatch(HostInput::InactivityTimeout).await;
         }
-        was_connected = connected;
     }
 }
+
+/// Feed raw bytes into the frame decoder. For each complete frame:
+/// - Ok → route into the command channel (or emit sync ERR on parse fail)
+/// - Err(Crc | Cobs | TooShort) → emit async ERR(EFRAME)
+///
+/// Borrow-scoped per the `FrameDecoder::feed` callback contract: the
+/// payload slice is valid only for the duration of the callback.
+async fn dispatch_bytes(
+    decoder: &mut FrameDecoder,
+    bytes: &[u8],
+    commands: &'static CommandChannel,
+    outbound: &'static OutboundChannel,
+) {
+    // `FrameDecoder::feed` hands payloads by reference; we must synchronously
+    // copy any data we need before the callback returns. To avoid fighting
+    // lifetimes we accumulate per-frame work as an enum.
+    let mut work: heapless::Vec<FrameWork, 4> = heapless::Vec::new();
+    decoder.feed(bytes, |res| match res {
+        FrameResult::Ok {
+            type_id,
+            tag,
+            payload,
+        } => {
+            let mut p: heapless::Vec<u8, { crate::protocol::MAX_PAYLOAD_FIELD }> =
+                heapless::Vec::new();
+            let _ = p.extend_from_slice(payload);
+            let _ = work.push(FrameWork::Ok {
+                type_id,
+                tag,
+                payload: p,
+            });
+        }
+        FrameResult::Err(_e) => {
+            let _ = work.push(FrameWork::Frame);
+        }
+    });
+    for w in work {
+        match w {
+            FrameWork::Ok {
+                type_id,
+                tag,
+                payload,
+            } => {
+                dispatch_frame(type_id, tag, &payload, commands, outbound).await;
+            }
+            FrameWork::Frame => {
+                emit_async_err(outbound, ErrorCode::EFrame).await;
+            }
+        }
+    }
+}
+
+#[allow(clippy::large_enum_variant)]
+enum FrameWork {
+    Ok {
+        type_id: u8,
+        tag: u16,
+        payload: heapless::Vec<u8, { crate::protocol::MAX_PAYLOAD_FIELD }>,
+    },
+    Frame,
+}

src/lbt.rs

@@ -0,0 +1,285 @@
+//! Pure-math helpers for Listen-Before-Talk (CAD) retry timing.
+//!
+//! The CAD retry loop in `radio::do_tx` scales its backoff to the active
+//! LoRa configuration: per-retry sleep is one time-on-air of an assumed
+//! peer packet, total retry budget is capped at `CAD_BUDGET_US`. This
+//! module owns the ToA math (Semtech AN1200.13) and the retry-count
+//! derivation, split out so it can be unit-tested host-side without the
+//! radio module's hardware dependencies.
+
+use crate::protocol::{LoRaCodingRate, LoRaConfig, LoRaHeaderMode};
+
+/// Total LBT budget: the maximum time the CAD retry loop is allowed to
+/// tie up the radio before returning `ChannelBusy`.
+pub const CAD_BUDGET_US: u32 = 2_500_000;
+/// Upper bound on retries, independent of budget — caps the work on
+/// very fast configs (SF7/BW500 would otherwise get 60+ retries).
+pub const CAD_HARD_CAP: u8 = 10;
+/// Assumed peer-packet payload (bytes) used to size the per-retry sleep.
+/// 80 is a representative median for typical mesh traffic. Peers sending
+/// larger packets may be partially under-waited (accepted trade-off —
+/// host-level retry handles collisions).
+#[allow(dead_code)] // consumed by `radio.rs`, which is gated out of test builds
+pub const CAD_ASSUMED_PEER_PAYLOAD_B: u16 = 80;
+/// Jitter applied to each sleep, in tenths of a percent (±20 % = 200).
+pub const CAD_JITTER_TENTHS_PCT: u32 = 200;
+
+/// ToA formula expects CR ∈ {1..4} for 4/5..4/8 (each coded symbol carries
+/// `CR+4` bits). The protocol enum starts at 0, so map explicitly — using
+/// `as u32` alone would underestimate airtime by one code bit everywhere.
+pub fn cr_numeric(cr: LoRaCodingRate) -> u32 {
+    match cr {
+        LoRaCodingRate::Cr4_5 => 1,
+        LoRaCodingRate::Cr4_6 => 2,
+        LoRaCodingRate::Cr4_7 => 3,
+        LoRaCodingRate::Cr4_8 => 4,
+    }
+}
+
+/// Worst-case LoRa time-on-air in microseconds (Semtech AN1200.13).
+///
+/// Uses `N_preamble + 4.25` quarter-symbols for preamble duration; SX126x
+/// uses 6.25 at SF5/SF6, so the result is low by 2·T_sym at those SFs
+/// (sub-millisecond — negligible at the LBT-budget scale).
+pub fn toa_us(cfg: &LoRaConfig, payload_len: u16) -> u32 {
+    let sf = cfg.sf as u64;
+    let bw_hz = cfg.bw.as_hz() as u64;
+    // Symbol time in µs: (2^SF / BW_Hz) * 1e6. u64 avoids overflow at
+    // SF12/BW7 where T_sym ≈ 524 ms.
+    let t_sym_us = (1u64 << sf) * 1_000_000 / bw_hz.max(1);
+    let de: i64 = if t_sym_us > 16_000 { 1 } else { 0 };
+    let crc: i64 = if cfg.payload_crc { 1 } else { 0 };
+    let h: i64 = if matches!(cfg.header_mode, LoRaHeaderMode::Implicit) {
+        1
+    } else {
+        0
+    };
+    let pl = payload_len as i64;
+    let sf_i = sf as i64;
+
+    // Payload symbol count (signed intermediates — `num` goes negative
+    // for small PL at SF12 with H=1, CRC=0).
+    let num = 8 * pl - 4 * sf_i + 28 + 16 * crc - 20 * h;
+    let den = 4 * (sf_i - 2 * de);
+    let payload_sym_ceil = if num <= 0 || den <= 0 {
+        0i64
+    } else {
+        (num + den - 1) / den
+    };
+    let cr_num = cr_numeric(cfg.cr) as i64;
+    let n_payload = 8 + (payload_sym_ceil * (cr_num + 4)).max(0);
+    let t_payload_us = n_payload as u64 * t_sym_us;
+
+    // Preamble duration: (N + 4.25) * T_sym = (4·N + 17) * T_sym / 4.
+    let t_preamble_us = (cfg.preamble_len as u64 * 4 + 17) * t_sym_us / 4;
+
+    (t_preamble_us + t_payload_us).min(u32::MAX as u64) as u32
+}
+
+/// Derive the CAD retry count and per-retry sleep from the cached
+/// `cad_retry_delay_us`. Retries form: N CADs separated by N-1 sleeps.
+/// When one assumed-packet wait exceeds the total budget, `retries = 1`
+/// — a single CAD, bail on busy, no sleep.
+pub fn cad_retries(cad_retry_delay_us: u32) -> (u8, u32) {
+    if cad_retry_delay_us == 0 {
+        // Unconfigured should never reach this path; fall back to a
+        // single CAD with no sleep rather than divide-by-zero.
+        return (1, 0);
+    }
+    let n_sleeps = CAD_BUDGET_US / cad_retry_delay_us;
+    let retries = (n_sleeps + 1).clamp(1, CAD_HARD_CAP as u32) as u8;
+    (retries, cad_retry_delay_us)
+}
+
+/// Apply ±`CAD_JITTER_TENTHS_PCT`/10 % jitter around `base_us`.
+/// `entropy` is a raw 32-bit source; caller provides it so this stays
+/// pure (radio task passes `Instant::now().as_ticks() as u32`).
+pub fn jittered_sleep_us(base_us: u32, entropy: u32) -> u32 {
+    let mixed = entropy.wrapping_mul(0x9E37_79B9);
+    let span = 2 * CAD_JITTER_TENTHS_PCT + 1; // e.g. 401 for ±20 %
+    let r = mixed % span; // 0..=2·CAD_JITTER_TENTHS_PCT
+    // factor_thousandths ∈ [1000 − CAD_JITTER_TENTHS_PCT, 1000 + CAD_JITTER_TENTHS_PCT]
+    let factor_thousandths = 1000 - CAD_JITTER_TENTHS_PCT + r;
+    ((base_us as u64 * factor_thousandths as u64) / 1000) as u32
+}
+
+#[cfg(test)]
+mod tests {
+    use super::*;
+    use crate::protocol::{LoRaBandwidth, LoRaCodingRate, LoRaConfig, LoRaHeaderMode};
+
+    fn cfg(sf: u8, bw: LoRaBandwidth, cr: LoRaCodingRate, preamble: u16, implicit: bool, crc: bool) -> LoRaConfig {
+        LoRaConfig {
+            freq_hz: 915_000_000,
+            sf,
+            bw,
+            cr,
+            preamble_len: preamble,
+            sync_word: 0x1424,
+            tx_power_dbm: 0,
+            header_mode: if implicit {
+                LoRaHeaderMode::Implicit
+            } else {
+                LoRaHeaderMode::Explicit
+            },
+            payload_crc: crc,
+            iq_invert: false,
+        }
+    }
+
+    /// Helper: assert `actual` is within `tolerance_pct`% of `expected_us`.
+    fn approx(actual_us: u32, expected_us: u32, tolerance_pct: u32) {
+        let diff = actual_us.abs_diff(expected_us);
+        let tol = expected_us * tolerance_pct / 100;
+        assert!(
+            diff <= tol,
+            "actual {} us not within {}% of expected {} us (diff {}, tol {})",
+            actual_us,
+            tolerance_pct,
+            expected_us,
+            diff,
+            tol
+        );
+    }
+
+    // Reference values sanity-checked against Semtech's LoRa calculator
+    // and AN1200.13.
+
+    #[test]
+    fn toa_sf7_bw125_cr45_pl10_explicit_crc() {
+        let c = cfg(7, LoRaBandwidth::Khz125, LoRaCodingRate::Cr4_5, 8, false, true);
+        // Hand-computed reference from AN1200.13:
+        //   T_sym = 128/125 kHz = 1.024 ms
+        //   T_preamble = (8 + 4.25) · 1.024 = 12.544 ms
+        //   n_payload = 8 + ceil((80 − 28 + 28 + 16) / 28) · 5 = 8 + 4·5 = 28
+        //   T_payload = 28 · 1.024 = 28.672 ms
+        //   Total ≈ 41.22 ms
+        approx(toa_us(&c, 10), 41_216, 2);
+    }
+
+    #[test]
+    fn toa_sf12_bw125_cr45_pl10_explicit_crc() {
+        let c = cfg(12, LoRaBandwidth::Khz125, LoRaCodingRate::Cr4_5, 8, false, true);
+        // Reference: ~991 ms for PL=10 at SF12/BW125/CR4/5 (LDRO on).
+        approx(toa_us(&c, 10), 991_000, 2);
+    }
+
+    #[test]
+    fn toa_sf10_bw125_cr45_pl255_max() {
+        let c = cfg(10, LoRaBandwidth::Khz125, LoRaCodingRate::Cr4_5, 8, false, true);
+        // Reference: ~2.34 s for PL=255 at SF10/BW125/CR4/5.
+        approx(toa_us(&c, 255), 2_335_000, 2);
+    }
+
+    #[test]
+    fn toa_ldro_activates_at_sf11_and_sf12_bw125() {
+        // T_sym > 16 ms → DE=1. SF11/BW125: T_sym = 16.384 ms. SF10/BW125: 8.192 ms.
+        let sf10 = cfg(10, LoRaBandwidth::Khz125, LoRaCodingRate::Cr4_5, 8, false, true);
+        let sf11 = cfg(11, LoRaBandwidth::Khz125, LoRaCodingRate::Cr4_5, 8, false, true);
+        let sf12 = cfg(12, LoRaBandwidth::Khz125, LoRaCodingRate::Cr4_5, 8, false, true);
+        // Crude check: each step roughly doubles airtime (LDRO doesn't
+        // break the doubling trend — it just shifts constants).
+        let t10 = toa_us(&sf10, 80);
+        let t11 = toa_us(&sf11, 80);
+        let t12 = toa_us(&sf12, 80);
+        assert!(t11 > t10 * 15 / 10, "SF11 should be > 1.5x SF10, got {} vs {}", t11, t10);
+        assert!(t12 > t11 * 15 / 10, "SF12 should be > 1.5x SF11, got {} vs {}", t12, t11);
+    }
+
+    #[test]
+    fn toa_assumed_peer_80b_matches_plan_table() {
+        let mk = |sf, bw| cfg(sf, bw, LoRaCodingRate::Cr4_5, 8, false, true);
+        // Plan table values (approximate, within 5%).
+        approx(toa_us(&mk(7, LoRaBandwidth::Khz500), 80), 36_000, 5);
+        approx(toa_us(&mk(7, LoRaBandwidth::Khz250), 80), 72_000, 5);
+        approx(toa_us(&mk(7, LoRaBandwidth::Khz125), 80), 144_000, 5);
+        approx(toa_us(&mk(8, LoRaBandwidth::Khz125), 80), 257_000, 5);
+        approx(toa_us(&mk(9, LoRaBandwidth::Khz125), 80), 452_000, 5);
+        approx(toa_us(&mk(10, LoRaBandwidth::Khz125), 80), 862_000, 5);
+        approx(toa_us(&mk(11, LoRaBandwidth::Khz125), 80), 1_806_000, 5);
+        approx(toa_us(&mk(12, LoRaBandwidth::Khz125), 80), 3_285_000, 5);
+    }
+
+    #[test]
+    fn toa_no_underflow_at_small_pl_sf12_implicit_no_crc() {
+        // num = 8·PL − 4·SF + 28 + 16·CRC − 20·H goes negative here; the
+        // i64 + max(0) guard must kick in without panicking or wrapping.
+        let c = cfg(12, LoRaBandwidth::Khz125, LoRaCodingRate::Cr4_5, 8, true, false);
+        let t = toa_us(&c, 1);
+        // Only 8 payload symbols survive (the formula floors to 0 extra);
+        // should be preamble + 8·T_sym ≈ 401 + 262 = 663 ms roughly.
+        approx(t, 663_000, 5);
+    }
+
+    // Retry-count derivation table from the plan.
+
+    #[test]
+    fn retries_sf7_bw500_hits_hard_cap() {
+        let (n, s) = cad_retries(36_000);
+        assert_eq!(n, 10);
+        assert_eq!(s, 36_000);
+    }
+
+    #[test]
+    fn retries_sf10_bw125() {
+        // T_assumed ≈ 862 ms; budget 2.5 s ⇒ 2 sleeps ⇒ 3 retries.
+        let (n, _) = cad_retries(862_000);
+        assert_eq!(n, 3);
+    }
+
+    #[test]
+    fn retries_sf11_bw125() {
+        // T_assumed ≈ 1.81 s; budget 2.5 s ⇒ 1 sleep ⇒ 2 retries.
+        let (n, _) = cad_retries(1_806_000);
+        assert_eq!(n, 2);
+    }
+
+    #[test]
+    fn retries_sf12_bw125_degraded() {
+        // T_assumed ≈ 3.29 s > 2.5 s budget ⇒ 0 sleeps ⇒ 1 retry (bail on busy).
+        let (n, _) = cad_retries(3_285_000);
+        assert_eq!(n, 1);
+    }
+
+    #[test]
+    fn retries_zero_delay_falls_back_to_single_cad() {
+        // Unconfigured safety: avoid divide-by-zero.
+        let (n, s) = cad_retries(0);
+        assert_eq!(n, 1);
+        assert_eq!(s, 0);
+    }
+
+    // Jitter sanity.
+
+    #[test]
+    fn jitter_stays_within_pm_20_pct() {
+        let base = 1_000_000u32;
+        // Exhaustive over the low byte — enough to cover the `% span` range.
+        let mut saw_low = false;
+        let mut saw_high = false;
+        for e in 0u32..=u16::MAX as u32 {
+            let j = jittered_sleep_us(base, e);
+            // ±20% ⇒ [800_000, 1_200_000].
+            assert!(
+                (800_000..=1_200_000).contains(&j),
+                "jitter {} us out of ±20% bounds for entropy {}",
+                j,
+                e
+            );
+            if j <= 850_000 {
+                saw_low = true;
+            }
+            if j >= 1_150_000 {
+                saw_high = true;
+            }
+        }
+        assert!(saw_low && saw_high, "jitter didn't span the expected range");
+    }
+
+    #[test]
+    fn jitter_zero_base_is_zero() {
+        for e in [0u32, 1, 42, 0xDEAD_BEEF] {
+            assert_eq!(jittered_sleep_us(0, e), 0);
+        }
+    }
+}

src/main.rs

@@ -19,6 +19,8 @@
 mod board;
 #[cfg(not(test))]
 mod channel;
+#[cfg(all(not(test), feature = "debug-checkpoint"))]
+mod debug_blink;
 #[cfg(not(test))]
 mod display;
 #[cfg(not(test))]
@@ -27,6 +29,7 @@ mod driver;
 mod hal;
 #[cfg(not(test))]
 mod host;
+mod lbt;
 mod protocol;
 #[cfg(not(test))]
 mod radio;
@@ -37,14 +40,16 @@ use embassy_executor::Spawner;
 #[cfg(not(test))]
 use crate::board::LoRaBoard;
 #[cfg(not(test))]
-use crate::channel::{CommandChannel, DisplayCommandChannel, ResponseChannel, StatusWatch};
+use crate::channel::{CommandChannel, DisplayCommandChannel, OutboundChannel, RadioEventChannel};
+#[cfg(not(test))]
+use crate::protocol::{cap, Info, MAX_MCU_UID_LEN, MAX_RADIO_UID_LEN};
 
 #[cfg(not(test))]
 cfg_if::cfg_if! {
-    if #[cfg(any(feature = "rak_wisblock_4631", feature = "wio_tracker_l1"))] {
+    if #[cfg(any(feature = "rak_wisblock_4631", feature = "wio_tracker_l1", feature = "waveshare_rp2040_lora"))] {
         use defmt_rtt as _;
         use panic_probe as _;
-    } else if #[cfg(any(feature = "heltec_v3", feature = "heltec_v3_uart", feature = "heltec_v4"))] {
+    } else if #[cfg(any(feature = "heltec_v3", feature = "heltec_v3_uart", feature = "heltec_v4", feature = "elecrow_thinknode_m2", feature = "lilygo_tbeam_supreme", feature = "lilygo_tbeam"))] {
         use esp_backtrace as _;
         use esp_println as _;
     }
@@ -53,20 +58,22 @@ cfg_if::cfg_if! {
 #[cfg(not(test))]
 static COMMANDS: CommandChannel = CommandChannel::new();
 #[cfg(not(test))]
-static RESPONSES: ResponseChannel = ResponseChannel::new();
+static OUTBOUND: OutboundChannel = OutboundChannel::new();
 #[cfg(not(test))]
-static STATUS: StatusWatch = StatusWatch::new();
+static RADIO_EVENTS: RadioEventChannel = RadioEventChannel::new();
 #[cfg(not(test))]
 static DISPLAY_COMMANDS: DisplayCommandChannel = DisplayCommandChannel::new();
+#[cfg(not(test))]
+static mut INFO: Option<Info> = None;
 
 #[cfg(not(test))]
 cfg_if::cfg_if! {
-    if #[cfg(any(feature = "rak_wisblock_4631", feature = "wio_tracker_l1"))] {
+    if #[cfg(any(feature = "rak_wisblock_4631", feature = "wio_tracker_l1", feature = "waveshare_rp2040_lora"))] {
         #[embassy_executor::main]
         async fn main(spawner: Spawner) {
             run(spawner).await;
         }
-    } else if #[cfg(any(feature = "heltec_v3", feature = "heltec_v3_uart", feature = "heltec_v4"))] {
+    } else if #[cfg(any(feature = "heltec_v3", feature = "heltec_v3_uart", feature = "heltec_v4", feature = "elecrow_thinknode_m2", feature = "lilygo_tbeam_supreme", feature = "lilygo_tbeam"))] {
         #[esp_rtos::main]
         async fn main(spawner: Spawner) {
             run(spawner).await;
@@ -79,24 +86,110 @@ async fn run(spawner: Spawner) {
     let board = <board::Board as LoRaBoard>::init();
     let parts = board.into_parts();
 
-    spawner
-        .spawn(radio::radio_task(parts.radio, &COMMANDS, &RESPONSES, &STATUS))
-        .expect("spawn radio_task");
+    // Build the GET_INFO struct once at boot. This is the authoritative
+    // snapshot of device capabilities reported over the wire.
+    let info = build_info(parts.mac);
+    // SAFETY: touched only here at boot, before any task is spawned.
+    let info_ref: &'static Info = unsafe {
+        INFO = Some(info);
+        #[allow(static_mut_refs)]
+        INFO.as_ref().expect("INFO just initialized")
+    };
 
-    spawner
-        .spawn(host::host_task(
+    spawner.spawn(
+        radio::radio_task(parts.radio, &COMMANDS, &OUTBOUND, &RADIO_EVENTS, info_ref)
+            .expect("spawn radio_task"),
+    );
+
+    spawner.spawn(
+        host::host_task(
             parts.host,
             &COMMANDS,
-            &RESPONSES,
+            &OUTBOUND,
             &DISPLAY_COMMANDS,
             parts.display.is_some(),
             parts.mac,
-        ))
-        .expect("spawn host_task");
+        )
+        .expect("spawn host_task"),
+    );
+
+    // Suppress "assigned but never read" warning on non-USB/UART path.
+    let _ = info_ref;
 
     if let Some(dp) = parts.display {
-        spawner
-            .spawn(display::display_task(dp, parts.led, &STATUS, &DISPLAY_COMMANDS))
-            .expect("spawn display_task");
+        #[cfg(feature = "debug-checkpoint")]
+        {
+            // LED is taken over by the checkpoint blinker; the display
+            // init struct is dropped unused for this debug build.
+            let _ = dp;
+            spawner
+                .spawn(debug_blink::debug_blink_task(parts.led).expect("spawn debug_blink_task"));
+        }
+        #[cfg(not(feature = "debug-checkpoint"))]
+        {
+            #[allow(clippy::unit_arg)] // LedDriver is () for boards without LEDs
+            spawner.spawn(
+                display::display_task(dp, parts.led, &RADIO_EVENTS, &DISPLAY_COMMANDS)
+                    .expect("spawn display_task"),
+            );
+        }
     }
 }
+
+#[cfg(not(test))]
+fn build_info(mac: [u8; 6]) -> Info {
+    let (fmin, fmax) = <board::Board as LoRaBoard>::freq_range_hz();
+    let chip_id = <board::Board as LoRaBoard>::radio_chip_id();
+    let (tx_min, tx_max) = board::Board::TX_POWER_RANGE;
+    let supported_sf = <board::Board as LoRaBoard>::supported_sf_bitmap();
+    let supported_bw = <board::Board as LoRaBoard>::supported_bw_bitmap();
+
+    let mut mcu_uid = [0u8; MAX_MCU_UID_LEN];
+    mcu_uid[..6].copy_from_slice(&mac);
+
+    Info {
+        proto_major: 1,
+        proto_minor: 0,
+        fw_major: parse_u8_or(env!("CARGO_PKG_VERSION_MAJOR"), 0),
+        fw_minor: parse_u8_or(env!("CARGO_PKG_VERSION_MINOR"), 0),
+        fw_patch: parse_u8_or(env!("CARGO_PKG_VERSION_PATCH"), 0),
+        radio_chip_id: chip_id,
+        capability_bitmap: cap::LORA | cap::CAD_BEFORE_TX,
+        supported_sf_bitmap: supported_sf,
+        supported_bw_bitmap: supported_bw,
+        max_payload_bytes: crate::protocol::MAX_OTA_PAYLOAD as u16,
+        // Real channel depths from channel.rs.
+        rx_queue_capacity: 32,
+        tx_queue_capacity: 1,
+        freq_min_hz: fmin,
+        freq_max_hz: fmax,
+        tx_power_min_dbm: tx_min,
+        tx_power_max_dbm: tx_max,
+        mcu_uid_len: 6,
+        mcu_uid,
+        radio_uid_len: 0,
+        radio_uid: [0u8; MAX_RADIO_UID_LEN],
+    }
+}
+
+#[cfg(not(test))]
+const fn parse_u8_or(s: &str, default: u8) -> u8 {
+    // CARGO_PKG_VERSION_* strings are short decimal ascii. Parse them at
+    // compile time via a tiny constant function instead of pulling in a
+    // dependency.
+    let bytes = s.as_bytes();
+    let mut i = 0;
+    let mut out: u32 = 0;
+    while i < bytes.len() {
+        let b = bytes[i];
+        if b < b'0' || b > b'9' {
+            return default;
+        }
+        out = out * 10 + (b - b'0') as u32;
+        if out > u8::MAX as u32 {
+            return default;
+        }
+        i += 1;
+    }
+    out as u8
+}

src/protocol.rs

@@ -1,707 +1,16 @@
-//! Wire protocol types and fixed-size little-endian serialization.
+//! Wire protocol types for DongLoRa Protocol v2.
 //!
-//! Every integer is fixed-width LE. No varints, no zigzag.
-//! See `docs/PROTOCOL.md` for the complete specification.
-
-use heapless::Vec;
-
-/// Maximum LoRa payload size in bytes.
-pub const MAX_PAYLOAD: usize = 256;
-
-/// RadioConfig wire size (fixed).
-pub const RADIO_CONFIG_SIZE: usize = 13;
-
-/// Sentinel value for `tx_power_dbm`: use the board's maximum TX power.
-pub const TX_POWER_MAX: i8 = i8::MIN; // -128 on the wire
-
-/// Sentinel value for `preamble_len`: use the firmware default (16 symbols).
-pub const PREAMBLE_DEFAULT: u16 = 0;
-
-/// LoRa signal bandwidth.
-#[derive(Debug, Clone, Copy, PartialEq, Eq)]
-#[cfg_attr(not(test), derive(defmt::Format))]
-#[repr(u8)]
-pub enum Bandwidth {
-    Khz7 = 0,
-    Khz10 = 1,
-    Khz15 = 2,
-    Khz20 = 3,
-    Khz31 = 4,
-    Khz41 = 5,
-    Khz62 = 6,
-    Khz125 = 7,
-    Khz250 = 8,
-    Khz500 = 9,
-}
-
-impl Bandwidth {
-    fn from_u8(v: u8) -> Option<Self> {
-        match v {
-            0 => Some(Self::Khz7),
-            1 => Some(Self::Khz10),
-            2 => Some(Self::Khz15),
-            3 => Some(Self::Khz20),
-            4 => Some(Self::Khz31),
-            5 => Some(Self::Khz41),
-            6 => Some(Self::Khz62),
-            7 => Some(Self::Khz125),
-            8 => Some(Self::Khz250),
-            9 => Some(Self::Khz500),
-            _ => None,
-        }
-    }
-}
-
-/// Complete LoRa radio configuration.
-///
-/// Wire layout (13 bytes, all little-endian):
-/// ```text
-/// [freq_hz:4] [bw:1] [sf:1] [cr:1] [sync_word:2] [tx_power_dbm:1] [preamble_len:2] [cad:1]
-/// ```
-#[derive(Debug, Clone, Copy, PartialEq, Eq)]
-#[cfg_attr(not(test), derive(defmt::Format))]
-pub struct RadioConfig {
-    /// Frequency in Hz (150_000_000 - 960_000_000 for SX1262).
-    pub freq_hz: u32,
-    pub bw: Bandwidth,
-    /// Spreading factor (5-12).
-    pub sf: u8,
-    /// Coding rate denominator (5-8). E.g. 5 = CR 4/5, 8 = CR 4/8.
-    pub cr: u8,
-    pub sync_word: u16,
-    /// Transmit power in dBm. Set to [`TX_POWER_MAX`] (-128) for the
-    /// board's maximum.
-    pub tx_power_dbm: i8,
-    /// Preamble length in symbols. Set to [`PREAMBLE_DEFAULT`] (0) for
-    /// the firmware default (16 symbols). Valid range: 6–65535.
-    pub preamble_len: u16,
-    /// Channel Activity Detection (listen-before-talk) before TX.
-    /// 0 = disabled, non-zero = enabled. Default: 1 (enabled).
-    pub cad: u8,
-}
-
-impl RadioConfig {
-    /// Validate fields against hardware limits.
-    pub fn validate(&self, power_range: (i8, i8)) -> Result<(), &'static str> {
-        if !(150_000_000..=960_000_000).contains(&self.freq_hz) {
-            return Err("frequency out of range (150-960 MHz)");
-        }
-        if !(5..=12).contains(&self.sf) {
-            return Err("spreading factor out of range (5-12)");
-        }
-        if !(5..=8).contains(&self.cr) {
-            return Err("coding rate out of range (5-8)");
-        }
-        if self.tx_power_dbm != TX_POWER_MAX
-            && !(power_range.0..=power_range.1).contains(&self.tx_power_dbm)
-        {
-            return Err("TX power out of range for this board");
-        }
-        if self.preamble_len != PREAMBLE_DEFAULT && self.preamble_len < 6 {
-            return Err("preamble length too short (min 6)");
-        }
-        Ok(())
-    }
-
-    /// Resolve sentinel values to concrete defaults.
-    pub fn resolve(mut self, power_range: (i8, i8)) -> Self {
-        if self.tx_power_dbm == TX_POWER_MAX {
-            self.tx_power_dbm = power_range.1;
-        }
-        if self.preamble_len == PREAMBLE_DEFAULT {
-            self.preamble_len = 16;
-        }
-        self
-    }
-
-    /// Whether CAD (listen-before-talk) is enabled.
-    pub fn cad_enabled(&self) -> bool {
-        self.cad != 0
-    }
-
-    /// Serialize to fixed-size LE bytes. Returns number of bytes written (always 13).
-    pub fn write_to(self, buf: &mut [u8]) -> usize {
-        buf[0..4].copy_from_slice(&self.freq_hz.to_le_bytes());
-        buf[4] = self.bw as u8;
-        buf[5] = self.sf;
-        buf[6] = self.cr;
-        buf[7..9].copy_from_slice(&self.sync_word.to_le_bytes());
-        buf[9] = self.tx_power_dbm as u8;
-        buf[10..12].copy_from_slice(&self.preamble_len.to_le_bytes());
-        buf[12] = self.cad;
-        RADIO_CONFIG_SIZE
-    }
-
-    /// Deserialize from fixed-size LE bytes.
-    pub fn from_bytes(buf: &[u8]) -> Option<Self> {
-        if buf.len() < RADIO_CONFIG_SIZE {
-            return None;
-        }
-        Some(Self {
-            freq_hz: u32::from_le_bytes(buf[0..4].try_into().ok()?),
-            bw: Bandwidth::from_u8(buf[4])?,
-            sf: buf[5],
-            cr: buf[6],
-            sync_word: u16::from_le_bytes(buf[7..9].try_into().ok()?),
-            tx_power_dbm: buf[9] as i8,
-            preamble_len: u16::from_le_bytes(buf[10..12].try_into().ok()?),
-            cad: buf[12],
-        })
-    }
-}
-
-/// Host → firmware commands.
-#[allow(clippy::large_enum_variant)]
-#[derive(Debug, PartialEq)]
-pub enum Command {
-    Ping,
-    GetConfig,
-    SetConfig(RadioConfig),
-    StartRx,
-    StopRx,
-    Transmit {
-        config: Option<RadioConfig>,
-        payload: Vec<u8, MAX_PAYLOAD>,
-    },
-    DisplayOn,
-    DisplayOff,
-    GetMac,
-}
-
-impl Command {
-    /// Deserialize from a COBS-decoded frame.
-    pub fn from_bytes(buf: &[u8]) -> Option<Self> {
-        let tag = *buf.first()?;
-        let rest = &buf[1..];
-        match tag {
-            0 => Some(Self::Ping),
-            1 => Some(Self::GetConfig),
-            2 => Some(Self::SetConfig(RadioConfig::from_bytes(rest)?)),
-            3 => Some(Self::StartRx),
-            4 => Some(Self::StopRx),
-            5 => {
-                // Transmit: has_config:u8 + [RadioConfig if 1] + len:u16 LE + payload
-                if rest.is_empty() {
-                    return None;
-                }
-                let (config, pos) = if rest[0] == 0 {
-                    (None, 1)
-                } else if rest[0] == 1 && rest.len() > RADIO_CONFIG_SIZE {
-                    (
-                        Some(RadioConfig::from_bytes(&rest[1..])?),
-                        1 + RADIO_CONFIG_SIZE,
-                    )
-                } else {
-                    return None;
-                };
-                if rest.len() < pos + 2 {
-                    return None;
-                }
-                let len = u16::from_le_bytes(rest[pos..pos + 2].try_into().ok()?) as usize;
-                let data_start = pos + 2;
-                if rest.len() < data_start + len {
-                    return None;
-                }
-                let mut payload = Vec::new();
-                let _ = payload.extend_from_slice(&rest[data_start..data_start + len]);
-                Some(Self::Transmit { config, payload })
-            }
-            6 => Some(Self::DisplayOn),
-            7 => Some(Self::DisplayOff),
-            8 => Some(Self::GetMac),
-            _ => None,
-        }
-    }
-}
-
-/// Firmware → host responses.
-#[allow(clippy::large_enum_variant)]
-#[derive(Debug, PartialEq)]
-pub enum Response {
-    Pong,
-    Config(RadioConfig),
-    RxPacket {
-        rssi: i16,
-        snr: i16,
-        payload: Vec<u8, MAX_PAYLOAD>,
-    },
-    TxDone,
-    Ok,
-    Error(ErrorCode),
-    MacAddress([u8; 6]),
-}
-
-impl Response {
-    /// Serialize to fixed-size LE bytes. Returns number of bytes written.
-    pub fn write_to(self, buf: &mut [u8]) -> usize {
-        match self {
-            Self::Pong => {
-                buf[0] = 0;
-                1
-            }
-            Self::Config(cfg) => {
-                buf[0] = 1;
-                1 + cfg.write_to(&mut buf[1..])
-            }
-            Self::RxPacket { rssi, snr, payload } => {
-                buf[0] = 2;
-                buf[1..3].copy_from_slice(&rssi.to_le_bytes());
-                buf[3..5].copy_from_slice(&snr.to_le_bytes());
-                buf[5..7].copy_from_slice(&(payload.len() as u16).to_le_bytes());
-                buf[7..7 + payload.len()].copy_from_slice(&payload);
-                7 + payload.len()
-            }
-            Self::TxDone => {
-                buf[0] = 3;
-                1
-            }
-            Self::Ok => {
-                buf[0] = 4;
-                1
-            }
-            Self::Error(code) => {
-                buf[0] = 5;
-                buf[1] = code as u8;
-                2
-            }
-            Self::MacAddress(mac) => {
-                buf[0] = 6;
-                buf[1..7].copy_from_slice(&mac);
-                7
-            }
-        }
-    }
-}
-
-/// Error codes reported to the host.
-#[derive(Debug, Clone, Copy, PartialEq, Eq)]
-#[cfg_attr(not(test), derive(defmt::Format))]
-#[repr(u8)]
-pub enum ErrorCode {
-    InvalidConfig = 0,
-    RadioBusy = 1,
-    TxTimeout = 2,
-    // 3 reserved (was CrcError — SX1262 silently drops bad-CRC packets)
-    NotConfigured = 4,
-    NoDisplay = 5,
-}
-
-// ── Tests ───────────────────────────────────────────────────────────
-
-#[cfg(test)]
-mod tests {
-    use super::*;
-
-    fn make_config() -> RadioConfig {
-        RadioConfig {
-            freq_hz: 915_000_000,
-            bw: Bandwidth::Khz125,
-            sf: 7,
-            cr: 5,
-            sync_word: 0x3444,
-            tx_power_dbm: 22,
-            preamble_len: 16,
-            cad: 1,
-        }
-    }
-
-    // ── RadioConfig roundtrip ───────────────────────────────────────
-
-    #[test]
-    fn radio_config_roundtrip() {
-        let cfg = make_config();
-        let mut buf = [0u8; RADIO_CONFIG_SIZE];
-        let n = cfg.write_to(&mut buf);
-        assert_eq!(n, RADIO_CONFIG_SIZE);
-        assert_eq!(RadioConfig::from_bytes(&buf), Some(cfg));
-    }
-
-    #[test]
-    fn radio_config_roundtrip_all_bandwidths() {
-        for bw_val in 0u8..=9 {
-            let bw = Bandwidth::from_u8(bw_val).unwrap();
-            let cfg = RadioConfig {
-                freq_hz: 433_000_000,
-                bw,
-                sf: 12,
-                cr: 8,
-                sync_word: 0x1234,
-                tx_power_dbm: -9,
-                preamble_len: 16,
-                cad: 1,
-            };
-            let mut buf = [0u8; RADIO_CONFIG_SIZE];
-            cfg.write_to(&mut buf);
-            assert_eq!(RadioConfig::from_bytes(&buf), Some(cfg));
-        }
-    }
-
-    #[test]
-    fn radio_config_roundtrip_negative_power() {
-        let cfg = RadioConfig {
-            tx_power_dbm: TX_POWER_MAX,
-            ..make_config()
-        };
-        let mut buf = [0u8; RADIO_CONFIG_SIZE];
-        cfg.write_to(&mut buf);
-        assert_eq!(RadioConfig::from_bytes(&buf), Some(cfg));
-    }
-
-    #[test]
-    fn radio_config_from_short_buffer() {
-        let buf = [0u8; RADIO_CONFIG_SIZE - 1];
-        assert!(RadioConfig::from_bytes(&buf).is_none());
-    }
-
-    #[test]
-    fn radio_config_from_empty_buffer() {
-        assert!(RadioConfig::from_bytes(&[]).is_none());
-    }
-
-    #[test]
-    fn radio_config_invalid_bandwidth() {
-        let mut buf = [0u8; RADIO_CONFIG_SIZE];
-        make_config().write_to(&mut buf);
-        buf[4] = 255; // invalid bandwidth
-        assert!(RadioConfig::from_bytes(&buf).is_none());
-    }
-
-    // ── RadioConfig::validate ───────────────────────────────────────
-
-    #[test]
-    fn validate_freq_boundaries() {
-        let power_range = (-9, 22);
-        let base = make_config();
-
-        let mut cfg = RadioConfig {
-            freq_hz: 150_000_000,
-            ..base
-        };
-        assert!(cfg.validate(power_range).is_ok());
-
-        cfg.freq_hz = 960_000_000;
-        assert!(cfg.validate(power_range).is_ok());
-
-        cfg.freq_hz = 149_999_999;
-        assert!(cfg.validate(power_range).is_err());
-
-        cfg.freq_hz = 960_000_001;
-        assert!(cfg.validate(power_range).is_err());
-    }
-
-    #[test]
-    fn validate_sf_boundaries() {
-        let power_range = (-9, 22);
-        let base = make_config();
-
-        for sf in 5..=12 {
-            assert!(RadioConfig { sf, ..base }.validate(power_range).is_ok());
-        }
-        assert!(RadioConfig { sf: 4, ..base }.validate(power_range).is_err());
-        assert!(RadioConfig { sf: 13, ..base }
-            .validate(power_range)
-            .is_err());
-    }
-
-    #[test]
-    fn validate_cr_boundaries() {
-        let power_range = (-9, 22);
-        let base = make_config();
-
-        for cr in 5..=8 {
-            assert!(RadioConfig { cr, ..base }.validate(power_range).is_ok());
-        }
-        assert!(RadioConfig { cr: 4, ..base }.validate(power_range).is_err());
-        assert!(RadioConfig { cr: 9, ..base }.validate(power_range).is_err());
-    }
-
-    #[test]
-    fn validate_tx_power_max_sentinel() {
-        let cfg = RadioConfig {
-            tx_power_dbm: TX_POWER_MAX,
-            ..make_config()
-        };
-        assert!(cfg.validate((-9, 22)).is_ok());
-    }
-
-    #[test]
-    fn validate_tx_power_out_of_range() {
-        let cfg = RadioConfig {
-            tx_power_dbm: 23,
-            ..make_config()
-        };
-        assert!(cfg.validate((-9, 22)).is_err());
-
-        let cfg = RadioConfig {
-            tx_power_dbm: -10,
-            ..make_config()
-        };
-        assert!(cfg.validate((-9, 22)).is_err());
-    }
-
-    #[test]
-    fn validate_preamble_default_sentinel() {
-        let cfg = RadioConfig {
-            preamble_len: PREAMBLE_DEFAULT,
-            ..make_config()
-        };
-        assert!(cfg.validate((-9, 22)).is_ok());
-    }
-
-    #[test]
-    fn validate_preamble_boundaries() {
-        let power_range = (-9, 22);
-        let base = make_config();
-
-        assert!(RadioConfig {
-            preamble_len: 6,
-            ..base
-        }
-        .validate(power_range)
-        .is_ok());
-        assert!(RadioConfig {
-            preamble_len: 5,
-            ..base
-        }
-        .validate(power_range)
-        .is_err());
-    }
-
-    // ── RadioConfig::resolve ──────────────────────────────────────
-
-    #[test]
-    fn resolve_power_max_sentinel() {
-        let cfg = RadioConfig {
-            tx_power_dbm: TX_POWER_MAX,
-            ..make_config()
-        };
-        assert_eq!(cfg.resolve((-9, 22)).tx_power_dbm, 22);
-    }
-
-    #[test]
-    fn resolve_power_explicit_unchanged() {
-        let cfg = RadioConfig {
-            tx_power_dbm: 10,
-            ..make_config()
-        };
-        assert_eq!(cfg.resolve((-9, 22)).tx_power_dbm, 10);
-    }
-
-    #[test]
-    fn resolve_preamble_default() {
-        let cfg = RadioConfig {
-            preamble_len: PREAMBLE_DEFAULT,
-            ..make_config()
-        };
-        assert_eq!(cfg.resolve((-9, 22)).preamble_len, 16);
-    }
-
-    #[test]
-    fn resolve_preamble_explicit_unchanged() {
-        let cfg = RadioConfig {
-            preamble_len: 32,
-            ..make_config()
-        };
-        assert_eq!(cfg.resolve((-9, 22)).preamble_len, 32);
-    }
-
-    // ── Command::from_bytes ─────────────────────────────────────────
-
-    #[test]
-    fn command_ping() {
-        assert_eq!(Command::from_bytes(&[0]), Some(Command::Ping));
-    }
-
-    #[test]
-    fn command_get_config() {
-        assert_eq!(Command::from_bytes(&[1]), Some(Command::GetConfig));
-    }
-
-    #[test]
-    fn command_set_config() {
-        let cfg = make_config();
-        let mut buf = [0u8; 1 + RADIO_CONFIG_SIZE];
-        buf[0] = 2;
-        cfg.write_to(&mut buf[1..]);
-        assert_eq!(Command::from_bytes(&buf), Some(Command::SetConfig(cfg)));
-    }
-
-    #[test]
-    fn command_start_stop_rx() {
-        assert_eq!(Command::from_bytes(&[3]), Some(Command::StartRx));
-        assert_eq!(Command::from_bytes(&[4]), Some(Command::StopRx));
-    }
-
-    #[test]
-    fn command_transmit_no_config() {
-        let payload = b"hello";
-        let mut buf = [0u8; 64];
-        buf[0] = 5; // tag
-        buf[1] = 0; // has_config = false
-        buf[2..4].copy_from_slice(&(payload.len() as u16).to_le_bytes());
-        buf[4..9].copy_from_slice(payload);
-
-        match Command::from_bytes(&buf[..9]).unwrap() {
-            Command::Transmit { config, payload: p } => {
-                assert!(config.is_none());
-                assert_eq!(p.as_slice(), b"hello");
-            }
-            _ => panic!("expected Transmit"),
-        }
-    }
-
-    #[test]
-    fn command_transmit_with_config() {
-        let cfg = make_config();
-        let mut buf = [0u8; 64];
-        buf[0] = 5; // tag
-        buf[1] = 1; // has_config = true
-        cfg.write_to(&mut buf[2..]);
-        let payload = b"test";
-        let pos = 2 + RADIO_CONFIG_SIZE;
-        buf[pos..pos + 2].copy_from_slice(&(payload.len() as u16).to_le_bytes());
-        buf[pos + 2..pos + 6].copy_from_slice(payload);
-
-        match Command::from_bytes(&buf[..pos + 6]).unwrap() {
-            Command::Transmit { config, payload: p } => {
-                assert_eq!(config, Some(cfg));
-                assert_eq!(p.as_slice(), b"test");
-            }
-            _ => panic!("expected Transmit"),
-        }
-    }
-
-    #[test]
-    fn command_transmit_empty_payload() {
-        let mut buf = [0u8; 4];
-        buf[0] = 5; // tag
-        buf[1] = 0; // has_config = false
-        buf[2..4].copy_from_slice(&0u16.to_le_bytes());
-
-        match Command::from_bytes(&buf).unwrap() {
-            Command::Transmit { config, payload } => {
-                assert!(config.is_none());
-                assert!(payload.is_empty());
-            }
-            _ => panic!("expected Transmit"),
-        }
-    }
-
-    #[test]
-    fn command_transmit_truncated() {
-        // Tag only — missing has_config byte
-        assert!(Command::from_bytes(&[5]).is_none());
-
-        // has_config=1 but no config bytes
-        assert!(Command::from_bytes(&[5, 1]).is_none());
-
-        // has_config=0 but no length bytes
-        assert!(Command::from_bytes(&[5, 0]).is_none());
-
-        // has_config=0, length says 5 but only 2 bytes of payload
-        let mut buf = [0u8; 6];
-        buf[0] = 5;
-        buf[1] = 0;
-        buf[2..4].copy_from_slice(&5u16.to_le_bytes());
-        buf[4] = 0xAA;
-        buf[5] = 0xBB;
-        assert!(Command::from_bytes(&buf).is_none());
-    }
-
-    #[test]
-    fn command_display_and_mac() {
-        assert_eq!(Command::from_bytes(&[6]), Some(Command::DisplayOn));
-        assert_eq!(Command::from_bytes(&[7]), Some(Command::DisplayOff));
-        assert_eq!(Command::from_bytes(&[8]), Some(Command::GetMac));
-    }
-
-    #[test]
-    fn command_invalid_tag() {
-        assert!(Command::from_bytes(&[9]).is_none());
-        assert!(Command::from_bytes(&[255]).is_none());
-    }
-
-    #[test]
-    fn command_empty_buffer() {
-        assert!(Command::from_bytes(&[]).is_none());
-    }
-
-    // ── Response::write_to ──────────────────────────────────────────
-
-    #[test]
-    fn response_pong() {
-        let mut buf = [0u8; 1];
-        assert_eq!(Response::Pong.write_to(&mut buf), 1);
-        assert_eq!(buf[0], 0);
-    }
-
-    #[test]
-    fn response_config() {
-        let cfg = make_config();
-        let mut buf = [0u8; 1 + RADIO_CONFIG_SIZE];
-        let n = Response::Config(cfg).write_to(&mut buf);
-        assert_eq!(n, 1 + RADIO_CONFIG_SIZE);
-        assert_eq!(buf[0], 1);
-        assert_eq!(RadioConfig::from_bytes(&buf[1..]), Some(cfg));
-    }
-
-    #[test]
-    fn response_rx_packet() {
-        let mut payload = Vec::new();
-        let _ = payload.extend_from_slice(b"data");
-        let mut buf = [0u8; 64];
-        let n = Response::RxPacket {
-            rssi: -80,
-            snr: 10,
-            payload,
-        }
-        .write_to(&mut buf);
-        assert_eq!(n, 7 + 4); // tag(1) + rssi(2) + snr(2) + len(2) + "data"(4)
-        assert_eq!(buf[0], 2);
-        assert_eq!(i16::from_le_bytes([buf[1], buf[2]]), -80);
-        assert_eq!(i16::from_le_bytes([buf[3], buf[4]]), 10);
-        assert_eq!(u16::from_le_bytes([buf[5], buf[6]]), 4);
-        assert_eq!(&buf[7..11], b"data");
-    }
-
-    #[test]
-    fn response_tx_done() {
-        let mut buf = [0u8; 1];
-        assert_eq!(Response::TxDone.write_to(&mut buf), 1);
-        assert_eq!(buf[0], 3);
-    }
-
-    #[test]
-    fn response_ok() {
-        let mut buf = [0u8; 1];
-        assert_eq!(Response::Ok.write_to(&mut buf), 1);
-        assert_eq!(buf[0], 4);
-    }
-
-    #[test]
-    fn response_error_codes() {
-        let mut buf = [0u8; 2];
-        for (code, val) in [
-            (ErrorCode::InvalidConfig, 0),
-            (ErrorCode::RadioBusy, 1),
-            (ErrorCode::TxTimeout, 2),
-            (ErrorCode::NotConfigured, 4),
-            (ErrorCode::NoDisplay, 5),
-        ] {
-            let n = Response::Error(code).write_to(&mut buf);
-            assert_eq!(n, 2);
-            assert_eq!(buf[0], 5);
-            assert_eq!(buf[1], val);
-        }
-    }
-
-    #[test]
-    fn response_mac_address() {
-        let mac = [0xAA, 0xBB, 0xCC, 0xDD, 0xEE, 0xFF];
-        let mut buf = [0u8; 7];
-        let n = Response::MacAddress(mac).write_to(&mut buf);
-        assert_eq!(n, 7);
-        assert_eq!(buf[0], 6);
-        assert_eq!(&buf[1..7], &mac);
-    }
-}
+//! Wire definitions live in the `donglora-protocol` crate so host-side
+//! Rust projects can share them with the firmware without duplicating
+//! wire layouts. This module re-exports them unchanged so firmware
+//! modules can `use crate::protocol::*;`.
+
+#[allow(unused_imports)]
+pub use donglora_protocol::{
+    cap, commands, encode_frame, events, Command, CommandParseError, DeviceMessage,
+    DeviceMessageParseError, ErrorCode, FlrcConfig, FrameDecoder, FrameEncodeError, FrameResult,
+    FskConfig, Info, InfoParseError, LoRaBandwidth, LoRaCodingRate, LoRaConfig, LoRaHeaderMode,
+    LrFhssConfig, Modulation, ModulationId, OkPayload, Owner, RadioChipId, RxOrigin, RxPayload,
+    SetConfigResult, SetConfigResultCode, TxDonePayload, TxFlags, TxResult, MAX_MCU_UID_LEN,
+    MAX_OK_PAYLOAD, MAX_OTA_PAYLOAD, MAX_PAYLOAD_FIELD, MAX_RADIO_UID_LEN, MAX_WIRE_FRAME,
+};